Table of Contents
Advertisement
2. CONTROLS, INDICATORS AND CONNECTORS
2-9 Indications in Viewfinder (Cont'd)
● Status 1
In addition to the information on the Status 0 screen, this screen displays audio indicators and information on remaining tape,
voltage and lens F-number.
Display position
Display
8
Shows the input level of the audio input channel.
(Example)
Display ON/OFF can be selected using the VF DISPLAY menu screen.
CH1- - - - + - -
See "AUDIO DISPLAY" on page 72.
CH2- - - - + - -
9
STBY
VCR in standby mode
SAVE
VCR in save mode
STOP
VCR in stop mode
REC
VCR in record mode
FF
VCR in fast-forward mode
REW
VCR in rewind mode
EJECT
VCR in reverse search mode
0
(Example)
Remaining tape indication (displayed in 1-minute steps)
< 60
When the tape is used for a long time, the remaining tape may not be
(Example)
indicated accurately. At the beginning of the tape, in particular, the indication
12: 34: 56: 20
may show smaller value than the actual one.
Time code display
Time code display is available when the "REC TIME" item on the VF DISPLAY
menu screen is set to TIME CODE.
See "REC TIME" on page 72.
A
Voltage indication (displayed in 0.1 V steps)
(Example)
12.4V
Shows the F-number of the connected lens.
B
OPEN, F2, F2.8, F4,
It is not displayed when the lens is removed. For some lenses, no display
F5.6, F8, F11, F16,
appears.
CLOSE
Display ON/OFF can be selected on the VF DISPLAY menu screen.
See "F NO.DISPLAY" on page 72.
C
In the Super Scene Finder (S.S.F.) mode, the number of memorized scenes
(Example)
is shown.
M:99
M : In MARK mode
C : In CUE mode
Number: Number of memorized scenes
● Status 2
This screen displays the camera setup statuses.
Event display is not available while this screen is displayed.
Indication
SCENE FILE
A, B, OFF
WHITE BAL
A, B, PRESET, FAW
FILTER
3.2K, 5.6K, 5.6K+ND
SHUTTER
OFF, 1/100, 1/250, 1/500, 1/1000, 1/2000, 1/60.1 to 1/2084.6 (in VARIABLE mode),
EEI (in ALC mode)
GAIN
-3dB, 0dB, 6dB, 9dB, 12dB, 18dB, LOLUX, ALC
IRIS LEVEL
NORMAL, BACK L, SPOT L
FULL AUTO
ON, OFF
REC TIME
Remaining tape time or time code.
28
Function
Note:
When the RS-232C cable
i s c o n n e c t e d , t h e V C R
operation mode may not
be displayed correctly.
Indication Contents
27
2. CONTROLS, INDICATORS AND CONNECTORS
2. CONTROLS, INDICATORS AND CONNECTORS
2-9 Indications in Viewfinder (Cont'd)
Alarm Message Display
ACCU - FOCUS
G
Alarm message display
F
I
B
CH1 - - - - + - -
CH2 - - - - + - -
F 5 . 6
STBY
< 6 0
1 .
2
4V
Indication
LOW BATTERY
The battery capacity is nearly exhausted.
CLOSE CASSETTE COVER
The cassette cover is not closed.
VTR WARNING [HEAD]
Head clogging
VTR WARNING [SERVO]
Servo error
VTR WARNING [DEW]
Condensation
VTR WARNING [HARD]
Hardware error
VTR WARNING [STOP]
Operation stopped
VTR WARNING [REW]
Rewinding abnormality
TAPE NEAR END
Remaining tape time is less than about 2 minutes in the record mode
TAPE END
Tape end reached
REC INHIBIT
An unrecordable videocassette (the switch on the back of the cassette is set to SAVE) is
inserted.
NO TAPE
VTR trigger is pressed with no tape loaded.
28
The following alarm messages are displayed on the status 0 and status 1
screens.
Contents
29
Advertisement
Table of Contents
