Embers And Logs - Lennox MLDVT-30NM Care And Operation Instructions Manual

instaLL VoLcanic stone, GLoWinG

eMBers and LoGs

NOTE: Turn off all electricity to the appliance
before you install volcanic stone, embers
and logs.
1. Remove the front glass enclosure panel
(see Removing Glass Enclosure Panels on
page 7).
2. always handle logs carefully to prevent
breakage.
3. install decorative volcanic stone - Sprinkle
the decorative volcanic stone in a pleasing pat-
tern (see Figure 6). The volcanic stone should
be placed directly on top of the firebox bottom,
along the slope and to the back at the right and
left sides of the burner. Position any ceramic
fiber liners before placing the stone. Logs can
be positioned after the volcanic stone.
Volcanic Stone
Place Volcanaic
Stone As Shown
Figure 6
4. Placement of Glowing Embers -
Separate the Embers (rockwool) into pieces
about the size of a quarter (see Figure 7 ).
Keep the pieces fluffed up, not matted. Dis-
tribute these pieces over the surface of the
burner, as shown in Figures 8 and 9. Do not
use more than is necessary. ensure that the
main burner slots remain uncovered by the
ember material. Position the embers on the
small holes of the ember bed area.
Note: This appliance is provided with enough
Glowing Embers for several applications, do
not use all that is in a new bag at one time.
For best glowing effect, replace the ember
material annually.
8
Figure 7
Glowing Embers
Separate into Quarter
Size (separate) Pieces
Bag of Glowing
Embers (rockwool)
5. placement of Logs -
All logs that have locating notches or slots to
help ensure that they are properly positioned.
All top logs that rest on lower logs, do so over
notches, indents or nubs. Proper log placement
is critical to prevent sooting. Logs should be
placed in the gaps between the flame peaks and
should be positioned so they do not impinge
the flames.
MLDVT-30 & MLDVT-35 - Install the five logs
as Follows:
Carefully position the ceramic fiber logs over
the burner as shown in Figure 8. Logs should
be placed in the order shown and per the fol-
lowing instructions.
1. Place the rear log (1) as shown. Position
it on the left rear log bracket.
2. Place the left front log (2) as shown. Posi-
tion it against the left front of the log rack.
3. Place the right front log (3) as shown. Posi-
tion it against the right front of the log rack.
4. Place the left cross log (4) as shown. Posi-
tion it over the rear log (1), with the front of
the log resting on the log rack.
5. Place the right cross log (5) as shown.
Position it over the right log (3), and rest the
rear of the log over the right rear bracket.
MLDVT-40 & MLDVT-45 - Install the five logs
as Follows:
Carefully position the ceramic fiber logs over
the burner as shown in Figure 9. Logs should
be placed in the order shown and per the fol-
lowing instructions.
1. Place the rear log (1) as shown. Position
it on the left rear log bracket.
2. Place the left front log (2) as shown. Posi-
tion it against the left front of the log rack.
NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
3. Place the right front log (3) as shown. Posi-
tion it against the right front of the log rack.
4. Place the left cross log (4) as shown. Posi-
tion it over the rear log (1), with the front of
the log resting over log (2).
5. Place the right cross log (5) as shown.
Position it over the right log (3), and rest the
rear of the log over the right rear bracket.
WarninG: do not attempt to
install the logs until the appliance
installation has been completed,
the gas line connected and tested
for leaks and the initial burner
operation has been checked out.
WarninG: the size and position
of the log set was engineered to
give the appliance a safe, reliable
and attractive flame pattern. any
attempt to use a different log set
in the fireplace will void the war-
ranty and will result in incomplete
combustion, sooting, and poor
flame quality.
WarninG: this appliance is
not designed to burn wood. any
attempt to do so could cause irrep-
arable damage to appliance and
prove hazardous to your safety.
WarninG: if logs are not installed
according to the log installation
instructions, flame impingement
and improper combustion could
occur and result in soot and/or
excessive production of carbon
monoxide (co), a colorless, odor-
less, toxic gas.
reFerence
Firebox accessories / parts
cat. no. Model no. description
88L53 FGe Bag of Glowing embers
(1 oz. rockwool)
Bag of decorative
80L42 FdVs
Volcanic stone