JVC GR-D20 Instructions Manual page 31

Make sure to set "S/AV INPUT" to "OFF" in the Menu
Screen (GR-D50/D30 only,
Set the video out select switch of the cable adapter as
required:
Y/C : When connecting to a TV or VCR which accepts
Y/C signals and uses an S-Video cable.
CVBS : When connecting to a TV or VCR which does not
accept Y/C signals and uses an audio/video
cable.
When editing on a VCR equipped with a DV input
connector, an optional DV cable can be connected
instead of an S-Video cable and audio/video cable.
(
To EDIT
S-Video cable
(optional)
Editing cable***
"Y/C"/"CVBS"
video out
select switch
To Remote PAUSE
or R.A.EDIT
$
To PAUSE IN
9
!
@
* Connect when an S-Video cable is not used.
** When connecting cables, open this cover.
*** Provided with the optional Remote Control kit
RM-V717KITU.
pg. 24).
*
To AV
Connector
cover**
To
)
S-VIDEO
Audio/Video cable
(provided)
To AUDIO, VIDEO*
and -IN
connectors
If your VCR has the
SCART connector,
use the provided
cable adapter.
VCR
4
TV
)
r
#
SELECT SCENES
4
Point the remote control at the camcorder's remote
sensor. Press PLAY (4)
r
ON/OFF on the remote control.
The Random Assemble Editing Menu appears.
N I
1 – – – – : – – ~
2
3
4
Programme
5
6
7
8
T I ME CODE
TOTAL
5
If using a Fade/Wipe at the beginning of the scene,
9
press FADE/WIPE on the remote control.
• Cycle through the effects by pressing repeatedly, and
stop when the one you want is displayed.
6
At the beginning of the scene, press EDIT IN/OUT
@
on the remote control. The Edit-In position appears
in the Random Assemble Editing Menu.
7
At the end of the scene, press EDIT IN/OUT
Edit-Out position appears in the Random Assemble
Editing Menu.
8
If using a Fade/Wipe at the end of the scene, press
9
FADE/WIPE .
• Cycle through the effects by pressing repeatedly, and
stop when the one you want is displayed.
• If you select a Fade/Wipe effect for an Edit-Out point,
the effect is automatically applied to the following
Edit-In point.
• When you use Fade/Wipe effects, that time is
included in the total time.
9
If using Playback Special Effects, press EFFECT
( pg. 28).
10
Repeat steps 6 through 9 to register additional
scenes.
• To change previously registered points, press
#
CANCEL on the remote control. The registered
points disappear, one at a time, from the most
recently registered point.
• If you are not using Fade/Wipe or Programme AE with
special effects, repeat steps 6 and 7 only.
NOTES:
When choosing a scene, set Edit-In and Edit-Out points
so that there is a relatively large difference between
them.
If the search time for an in-point exceeds 5 minutes, the
recording deck's Record-Standby mode will be cancelled
and editing will not take place.
If there are blank portions before or after the Edit-In and
Edit-Out points, a blue screen may be included in the
edited version.
Since time codes register time only as accurately as
seconds, the time code total time may not match the total
programme time exactly.
Turning off the camcorder's power erases all registered
Edit-In and Edit-Out points.
USING THE REMOTE CONTROL UNIT
)
and then press R.A.EDIT
OUT MODE
Random
~ Assemble
~
Editing Menu
~
~
~
~
~
– – : – –
0 0 : 00
@
Continued on next page.
. The
!
EN
31