KX-TDA600BX CONTENTS Page Page 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) 12.2. ASIC (IC102) 1.1. SUGGESTED PbF SOLDER 13 TERMINAL GUIDE OF ICS, TRANSISTORS AND DIODES 1.2. HOW TO RECOGNIZE THAT Pb FREE SOLDER IS 14 HOW TO REPLACE A FLAT PACKAGE IC USED 14.1.
KX-TDA600BX 1 ABOUT LEAD FREE SOLDER (PbF: Pb free) Note: In the information below, Pb, the symbol for lead in the periodic table of elements, will refer to standard solder or solder that contains lead. We will use PbF when discussing the lead free solder used in our manufacturing process which is made from Tin, (Sn), Silver, (Ag), and Copper, (Cu).
KX-TDA600BX 2 FOR SERVICE TECHNICIANS ICs and LSIs are vulnerable to static electricity. When repairing, the following precautions will help prevent recurring malfunctions. 1. Cover the plastic parts boxes with aluminum foil. 2. Ground the soldering irons. 3. Use a conductive mat on the worktable.
KX-TDA600BX 4 SPECIFICATIONS 4.1. GENERAL DESCRIPTION Control Bus Original bus (16 bit, 8 MHz,10 megabytes per second) Communication Bus H.100 bus conformity (1024 time slot) Switching Distributed Switching Power Input PSU-M 100 V AC to 130 V AC, 2.5 A/200 V AC to 240 V AC, 1.4 A, 50 Hz/60 Hz PSU-L 100 V AC to 130 V AC, 5.1 A/200 V AC to 240 V AC, 2.55 A, 50 Hz/60 Hz...
KX-TDA600BX 4.3. SYSTEM CONSTRUCTION 4.3.1. Basic System Basic Shelf The Basic Shelf contains an EMPR card for controlling the Hybrid IP-PBX. To use the basic system, install a power supply unit (PSU) in the PSU Slot and optional service cards in Free Slots. To expand to a multiple-shelf system, you also need to install a BUS-M card in the BUS-M Card Slot.
Page 8
KX-TDA600BX 2-shelf System Expanded system (Basic Shelf + 1 Expansion Shelf). Expansion Shelf 1 is mounted on the Basic Shelf. Note If you are installing a 2-shelf system in an area prone to earthquakes, make sure to fix the system to the wall using the wall brackets (supplied with an optional Mounting Kit).
Page 9
KX-TDA600BX 4-shelf System (Tower Type) Fully expanded system (Basic Shelf + 3 Expansion Shelves). Expansion Shelves 1 to 3 are mounted on the Basic Shelf. A Mounting Kit is required for the 4-shelf system.
Page 10
KX-TDA600BX 4-shelf System (Side-by-side Type) When vertical space is limited, it is possible to install a fully expanded system (Basic Shelf + Expansion Shelf 1, and Expansion Shelf 2 + Expansion Shelf 3) in a side-by-side configuration. Expansion Shelf 1 is mounted on the Basic Shelf, and Expansion Shelf 3 is mounted on Expansion Shelf 2.
KX-TDA600BX 4.4. SYSTEM CAPACITY 4.4.1. Maximum Trunk Port and Extension Port The Hybrid IP-PBX supports the following number of trunk ports and extension ports. Port Type Basic System 2-shelf System 3-shelf System 4-shelf System Trunk Extension DPT Port SLT Port...
Page 12
KX-TDA600BX 4.4.2. Maximum Terminal Equipment The following number of items of terminal equipment can be supported by the Hybrid IP-PBX. Terminal Equipment Type Basic System 2-shelf System 3-shelf System 4-shelf System Telephone (using Digital XDP) (240)*1 (480)*1 (720)*1 (960)*1 KX-T7600 series DPT...
Page 13
KX-TDA600BX Calculation Example Equipment Type Load Figure KX-T7600 series DPT 48 units Other DPT 4 units ESLC16 1 card EMSLC16 3 cards 8 ports Total The total load figure is 136. As this is between 128 and 512, you must install the PSU-L.
Page 16
Portable station: PS Single line telephone: SLT Note: Some optional service cards and features are not available for certain countries/areas. Consult your certified Panasonic dealer for detailed instructions. Important Notice Prior to connection of this product, please verify that the intended operating environment is supported.Satisfactory performance cannot be guaranteed for the following: - interoperability and compatibility with all devices and systems connected to this product.
KX-TDA600BX 6 DISASSEMBLY INSTRUCTIONS 6.1. DISASSEMBLY INSTRUCTION (EMPR CARD) 1. Remove the Lid by sliding it in the direction of the arrow 1. 2. This will be removed if the user attaches the Pad Lock as shown in a Fig.1.
KX-TDA600BX 6.2. DISASSEMBLY INSTRUCTION (BACK BOARD) 1. Remove four Screws (A). 2. Remove the Left Side Cover and the Right Side Cover. 3. Release the Hook and remove the Top Cover. 4. Remove nine Screws (B). 5. Remove the Back Cover.
Page 21
KX-TDA600BX 6. Remove the FAN Connector and LED Connector from the Back Board 1. 7. Remove eight Screws (C). 8. Remove the Back Board 1. 9. Remove the Back Board 2. 10. Remove the RS-232C Connector. 11. Remove the LED Connector from the LED Board.
KX-TDA600BX 7 OUTLINE 7.1. GENERAL DESCRIPTION The control system of this unit is composed of the main control section (EMPR) controlling the entire system, exchanging voice data, the circuit control section (LPR) controlling various telephone lines, connecting bus lines between basic shelf and expansion shelf (BUS-M) and the power supply section (POWER).
KX-TDA600BX 7.2. SYSTEM CONTROL 7.2.1. System Control Block Diagram...
Page 24
KX-TDA600BX 7.2.2. Voice (TDM Highway) Bus Block Diagram...
Page 25
KX-TDA600BX 7.2.3. Voice Bus Logical Assignment In the line card, the CT_D line number, which is output in accordance with the inserted slot, and the time slot are assigned on a software base. For the detail of output slot for each card, refer to the service manual of card.
KX-TDA600BX 8 EMPR CARD CIRCUIT OPERATION 8.1. EMPR CARD 8.1.1. Outline 1) Function • • • • System Control • • • • Circuit Switching (includes gain adjustment function) • • • • Conference Call (3 people x 8 ~ 8 people x 3) •...
Page 30
KX-TDA600BX 8.1.2. Description of Each Part LED light (BATT ALARM): Turns on to indicate the dropping of the lithium battery voltage (less than 2.8V). LED light (SD ACCESS): Turns on when the SD card is accessing. SD card slot: Mounts the system program SD card.
KX-TDA600BX 8.1.4. Circuit Description 8.1.4.1. Outline of Block Description • • • • CPU block This block operates the main unit control. Besides this operates various controls, select signal generation, DMA control and serial port control. This contains the built-in clock function.
Page 33
KX-TDA600BX Signal Name Function CH_SEL[0] Synchronous Signal for CODEC (For MOH#1/Page#1) CH_SEL[1] Synchronous Signal for CODEC (For MOH#2/Page#2) CH_SEL[2] Synchronous Signal for CODEC (For RMT) Clock Enable: CKE signal for SDRAM CKIO Clock I/O For bus clock of SDRAM (IC505, IC506) and ASIC (IC102). CPU (IC200) outputs the clock of four times frequency as many as Source clock (16.384MHz).
Page 34
KX-TDA600BX Signal Name Function M/nS Master/slave identification signal when SIC card (Future Option) as intersystem connection card is mounted. EMPR inputs this signal and detects which the EMPR will be. H: Master L: Slave MD0-2 Mode Control Terminal: Clock operation mode of CPU is set.MD2: L, MD1: L, MD0: H Fixed...
Page 35
KX-TDA600BX • • • • ASIC block Configuration: IC102 (ASIC), IC111, X103 and so on. Function: (IC102) This functions as the bus master of EC bus (synchronous bus with 16 bit width, transmission rate max.10Mbps). Communicates with ASIC mounted to each option card via EC bus and controls the option card.
Page 36
KX-TDA600BX voltage is supplied. +3.3V is generated by the DC/DC converter is converted to +1.5V and supplied to IC200 core power. BAT600, which is a lithium battery for memory backup, is connected to the power supply of IC621, IC622 (SRAM), IC411 (RTC)via D608, D609.
KX-TDA600BX 9 BACK BOARD CIRCUIT OPERATION The back board (BB) connects signals between all cards in KX-TDA600. It also supplies power from the power supply unit to the cards. CONNECTORS EXPLANATION (1) Power Supply Unit Connector: CN100 (2) Free Slot Connectors: CN101-CN110...
KX-TDA600BX 11 DIAGNOSIS 11.1. DIAGNOSIS FEATURES Card Test and Pair Port Test is in Diagnosis Features. 11.1.1. Card Test Card Test -SUMMARY Description Diagnose all kind of Cards.
Page 63
KX-TDA600BX 11.1.1.1. Local Loop Back Diagnosis Daignose faults by transmission of the data from the EMPR to the Option Card and back using the Loop back test. Since loopback points differ from each card, they consist of loopback tests of the following items:...
Page 64
KX-TDA600BX 11.1.1.4. DSP DTMF Generator / Receiver Diagnosis Diagnostic test for DTMF generator/receiver of DSP in the Card diagnosis point Time slot Time slot test Primary circuit Primary circuit loop back test DSP ST loop back DSP ST point loop back test...
Page 65
KX-TDA600BX 11.1.1.7. Framer IC Error Detection Diagnosis Diagnostic the feature to detect the alarm signal of Framer IC is operating correctly. Diagnosis point Bipolar violation error Bipolar violation error detection test CRC error CRC error detection test Framing error Framing error detection test...
Page 66
KX-TDA600BX 11.1.1.10. Caller ID Card Loop Back Diagnosis Diagnostic by Loop back test to the Caller ID card (Optional Card of ELCOT) Diagnosis result Caller ID card loop back diagnosis OK Caller ID card loop back diagnosis NG 11.1.1.11. Extension Mode Setting Test...
KX-TDA600BX 11.1.2. Pair Port Test Pair Port Test -SUMMARY Description Diagnostic Test to enable the connection of Ports for Internal and External Lines. DHLC SLC8 ESLC/EMSLC16 CS-INF ELCOT OPB3 E&M CTI- LINK Object of Card Diagnosis result Pair Port Test OK...
Page 68
KX-TDA600BX 2. Pair Port Test operation Select card for Test. 3. Click [Pair Port Test].
Page 69
KX-TDA600BX 4. Test [OK]. 5. Click [Cancel].
Page 70
KX-TDA600BX 6. Card Test operation Select card for Test. 7. Click [Card Test].
KX-TDA600BX 12 IC DATA 12.1. CPU (IC200) Pin No. Pin Name Description nRDY CPU bus ready signal nRESET CPU power on reset input port nCS0 Chip select 0 for Flash memory nCS1 Chip select 1 for BUS-M Card nCS4 Chip select 4 for SRAM...
Page 73
KX-TDA600BX Pin No. Pin Name Description D35/P3 nDSR2 for RS232C port VDDQ2 Power supply for IO(3.3V) VSSQ2 Power supply for IO(GND) D43/P11 nDC_ALM( DC alarm signal input port) D36/P4 DCD2 for RS232C port D42/P10 nAC_ALM(AC alarm signal input port) D37/P5...
Page 74
KX-TDA600BX Pin No. Pin Name Description VDDQ8 Power supply for IO(3.3V) VSSQ8 Power supply for IO(GND) nCS3 Chip select signal 3 for SDRAM on EMEC Card (reserved) nCS2 Chip select signal 2 for SDRAM on board VDD4 Power supply for CORE(1.5V)
Page 75
KX-TDA600BX Pin No. Pin Name Description MD2/RXD2 CPU Mode Serial interface for RS232C Port nIRL0 nIRQ_ASIC (Interrupt signal from ASIC) nIRL1 nIRQ_USB (Interrupt signal from USB controller) nIRL2 nIRQ_BUSM (Interrupt signal from BUS-M Card) nIRL3 nDC_ALM (DC Alarm Interrupt signal)
KX-TDA600BX 12.2. ASIC (IC102) Pin No. Pin Name Description Power Supply(GND) P3[7]/TXB[7] Pull up P3[6]/TXB[6] Pull up P3[5]/TXB[5] Pull up P3[4]/TXB[4] Pull up P3[3]/TXB[3] MASTER/nS P3[2]/TXB[2] M/nS P3[1]/TXB[1] POWTYPE[0] P3[0]/TXB[0] POWTYPE[1] Power Supply(GND) Power Supply(3.3V) P4[7] DIPSW7 fix"1" P4[6] DIPSW6 fix"1"...
Page 77
KX-TDA600BX Pin No. Pin Name Description RX[6] Connect to GND RX[5] Connect to GND RX[4] Connect to GND RX[3] Connect to GND RX[2] Connect to GND RX[1] Connect to GND RX[0] Connect to GND VREF_PLUS Connect to GND VREF_MINUS Connect to GND Power Supply(3.3V)
Page 78
KX-TDA600BX Pin No. Pin Name Description EC_nRST EC Bus Reset EC_BE[1] EC Bus Command[1] EC_BE[0] EC Bus Command[2] EC_PAR EC Bus parity Power Supply(GND) Power Supply(3.3V) EC_FRAME EC_Bus Frame signal EC_PERR EC Bus parity error detect EC_TRDY EC Bus Target ready...
Page 79
KX-TDA600BX Pin No. Pin Name Description nBREQ Bus request(NBREQ) nBACK Bus acknowledge(nBACK_NEXUS) nCS_SRAM SRAM chip select(nCS4_NEXDMA) nCS_MES ASIC chip select(nCS5) Power Supply(GND) Power Supply(3.3V) Read signal(nRD/nCAS) nWR[1] Write signal upper byte(nWE1/DQM1) nWR[0] Write signal lower byte(nWE0/DQM0) nBUSY ASIC Access Busy(nWAIT_ASIC1)
Page 80
KX-TDA600BX Pin No. Pin Name Description P2[5]234 Pull up P2[4]235 Pull up P2[3]236 Pull up P2[2]237 nINVALID_RS P2[1]238 nFORCEOFF_RS P2[0]239 FORCEON_RS Power Supply(GND)
KX-TDA600BX 14 HOW TO REPLACE A FLAT PACKAGE IC Even if you do not have the special tools (for example, a spot heater) to remove the Flat IC, with some solder (large amount), a soldering iron and a cutter knife, you can easily remove the ICs that have more than 100 pins.
KX-TDA600BX 17 REPLACEMENT PARTS LIST Note: Ref. Part No. Part Name & Description Remarks 1. RTL (Retention Time Limited) PSKK1035Z1 DOOR-LID, SCREW COVER PC+ABS( The marking (RTL) indicates that the Retention Time is PSKL1013Y1 STAND ABS(HB) limited for this item.
KX-TDA600BX 18 FOR THE SCHEMATIC DIAGRAM Note: 1. DC voltage measurements are taken with an oscilloscope or a tester with a ground. 2. The schematic diagrams and circuit board may be modified at any time with the development of new technology.