Advertisement
2. PROGRAMMING YOUR NEW TRANSMITTER (CONT)
4c. If the connector is placed on the top and
middle posts, that column is set on " + "
or "ON" or "CLOSE". If the connector is
placed on the middle and bottom posts,
that column is set on " - " or "OFF" or
"OPEN". If the connector is removed com-
pletely, (not placed on any posts), it is set
to " 0 " or the neutral position. (see
diagram G for examples of how to set a
column to the three different positions).
When removing a connector to set a
column to the neutral position, save the
connector in case you change the code
at a later date.
4d. To move the connectors, slide an opened
paper clip into the side of a connector and
lift. (see diagram H) When repositioning
connectors, place a connector on the two
chosen posts, then push down on the
connector with your finger.
Code connector setting to match your opener/motor
Linear
Position 1 to 8
M-O-M
Position 1 to 8
Stanley (310) Canada
Position 1 to 10
Stanley (300)
Position 1 to 10
Multi-Code
Position 1 to 10
Chamberlain
Position 1 to 9
Lift-Master
Position 1 to 9
Sears
Position 1 to 9
Wayne Dalton
Position 1 to 9
Master Mechanic
Position 1 to 9
Genie (9 positions)
Position 1 to 9
Genie (12 positions)
Position 1 to 12
Overhead
Position 1 to 9
Martec/Teckey
Position 1 to 10
Pulsar/Allister/Allstar
Position 1 to 9
Set the connectors numbered 1 through 12 to match the switches of
your existing transmitter or receiver. If your garage door opener is
manufactured by (Stanley
, Genie
®
Matic
) these switches may only have two positions, ( " + , ON, CLOSED"
®
and " - , OFF, OPEN"). (see diagram I) Set the connectors on the model
G5M to " + " if your existing switches are either " +, ON, CLOSE " and
set to " - " if your existing switches are either " -, OFF, OPEN". Do not
use the blank position "0".
Examples of how to set Model G5M
Existing
Transmitter
If your existing transmitter has fewer than 12
switches, match only the first corresponding
connectors. Leave the remaining posts blank
(remove the connectors). Press the button on
the transmitter.
If the garage door does not open, reverse all
of the connectors on the model G5M. The " + "
will be changed to the " - " position and the " -
" position will be changed to the " + " position.
(see diagram J)
If your garage door opener is manufactured by (Chamb erlain
Master
, Wayne Dalton
or Master Mechanic
®
®
positions, (" + , 0, - "). Set the connectors on the model G5M to match their
corresponding positions. If your opener is a Sears
Master
and the existing transmitter has three buttons, (see diagram K), the
®
first connector in the model #G5M may need to be changed to another
position. If your Chamberlain
®
match them to the first 9 connectors on the model G5M and remove the
last 3 connectors (connectors 10, 11, 12). If there are only 8 DIP switches
on your Chamberlain
,Sears
®
®
on the model G5M and remove the last 3 connectors (connectors 10, 11, 12).
'-' or 'OFF' or 'OPEN'
'+' or 'ON' or CLOSE
Diagram G
Diagram H
+ OR -
+ OR -
+ OR -
11,12 set to '+' or '-'
+ OR -
11,12 set to '+' or '-'
+ OR -
11,12 set to '+' or '-'
+, 0 (blank), OR -
+, 0 (blank), OR -
+, 0 (blank), OR -
+, 0 (blank), OR -
+, 0 (blank), OR -
+ OR -
+ OR -
+, 0 (blank), OR -
+ OR -
11,12 set to '+'
+, 0 (blank), OR -
, Multi-Code
, Linear
, Moore-O-
®
®
®
Model G5M
Diagram I
Original Position
Reversed Position
Diagram J
®
) the switches will have 3
®
, Chamberlain
®
,Sears
, Lift-Master
has 9 DIP switches,
®
®
, Lift-Master
, match them to the 2-9 position
®
2. PROGRAMMING YOUR NEW TRANSMITTER (CONT)
Now you may have to change the positioning
of the #1 connector on the model G5M. If the large
'0' = BLANK
button of Diagram K is used to open the garage
door, set the #1 connector to " - " position. If the
middle button is used, set the #1 connector to the
" 0 " or "blank" position. If the smaller button on the
left is used, s et the #1 connector to the " + " position.
To operate the model G5M with your GDO properly, please press the
button on the model G5M.
NOTE:
Transmission range may be reduced with use on a metal garage door.
12 volt alkaline battery (size 23A)
included.
If this transmitter triggers other garage doors in your neighborhood, change all your
transmitters and receiver to a new code setting.
DO NOT let children use the garage door transmitter without adult supervision.
Children can injure themselves or others by the garage door.
The Universal Garage Door Remote Control is approved by the FCC and it complies
with Part 15 of the FCC Rules. Its operation is subject to the f ollowing two conditions :
1. This device may not cause harmful interference.
2. This device must accept any interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party
responsible of compliance could void the user's authority to operate the equipment.
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
If your Skylink Universal Remote Control does not activate your Garage Door
Opener, the reason may be that your GDO age or manufacturer is not listed on the
compatibility chart.
The solution is the Skylink SG-18R Universal Receiver.
I f you would like to order Skylink's product or have difficulty getting your Skylink's
remote control to work, please :
1. visit our FAQ section at www.skylinkhome.com , or
2. email us at support@skylinkhome.com , or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
,Sears
, Lift-
®
or Lift-
®
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A396-001
US Patent. D380895, 5680134, 5841390, 6005508, 6956460
® are registered trademarks of their respective corporations
©2005 SKYLINK GROUP
3. OPERATION
4. BATTERY
5. WARNING
6. FCC
7. WARRANTY
8. CUSTOMER SERVICE
Diagram K
Advertisement
