Samsung HLS5087WX/XAA Service Manual page 25

6. TC90103
No Item
1 LIMYF
2 KMFY
3 KFY
4 LIMCF
5 KMFC
6 KFC
7 GVENH
8 VEN
9 VEC
10 FENH
11 PRENH
12 GHENH
13 NCLIM
14 GNC
15 GLTI
16 LTILIM
17 SET DELAY
18 GCTI
19 CTILIM
20 FLTI
21 FCTI
22 YCONT
23 YBRIT
24 CRGAIN
25 CBGAIN
26 CROFS
27 CBOFS
28 HUE
29 HUE BIAS
30 CKILL
31 BTCLON
32 BTCL ALT
33 YNRON
34 FILON
35 M_AGC_GAIN
36 3D/2D
37 SNR
Samsung Electronics
Range Default
0~7 2
0~3 2
0~7 3
0~7 2
0~3 2
0~7 3
0~3 1
0~3 3
0~3 1
0~1 0
0~1 0
0~15 2
0~7 0
0~3 1
0~3 0
0~3 0
0~15 10
0~3 0
0~3 0
0~1 0
0~1 0
0~255 66
0~255 249
0~15 0
0~15 1
0~15 1
0~15 1
0~127 0
0~63 0
0~7 7
0~1 1
0~1 0
- -
0~15 3
0~225 33
2D/3D 3D
- 117[0x75]
Remark
3D YNR limit level ; 000:small~111:large
Feed back factor for 3D YNR ; 0£:x1:1/2,2:x3/4, 3:OFF
3D YNR Ga in; 000£ºOFF~111:x0.875
3D CNR limit level ; 000£ºsmall~111:large (INIT:110)
Feed back factor for 3D CNR ;00:x 01:x1/2 10:x3/4 11:OFF
3D CNR Gain ;000:OFF~111x0.875
Vertical enhance gain ;00:OFF 10:x1/4 01:x1/8 11:x1/2
Setup V enhance NL ;00: 6IRE 10:13IRE 01: 9IRE 1:16IRE
Setup corng level for V enhance ;00:OFF 10:1.6IRE 01:0.8IRE 11:2.3IRE
Sharpness fo ; 0:4.2MHz 1:3.3MHz
Pre enhance 0:OFF 1:ON
Adjustment Sharpness gain
Coring for sharpness/noise cancel ; 0:0.8IRE 1:3.2IRE 2:1.6IRE 3:6.4IRE
Setup gain for noise cancel ; 00:OFF 10:x1/2 01:x1/4 11:x1
Setup L T I gain ;00:OFF 10:x1/4 01:x1/8 11:x1/2
Setup coring level for LTI ;00:0.8IRE 10:3.2IRE 01:1.6IRE 11:6.4IRE
Chroma signal delay adjustment0000:-296ns~000:Center ~ 1111:259ns(37ns step)
Setup CTI gain ; 00:OFF 10:x1/4 01:x1/8 11:x1/2
Setup coring level for CTI 00:0.4IRE 10;1.6IRE 01:0.8IRE 11:3.2IRE
LTI fo 0:3.3MHz 1:2.2MHz OFF
CTI fo 0:1.7MHz 1:3.4MHz
Contrast adjustment 00h:x1/2~40h:x1~ FFh:x2.4
Brightness adjustment ;128:-128LSB:0 OFF~127:+127LSB(10b i t ) b i t
C r signal gain adjustment ; 1000:x0~0000:x1~0111:x1.875
C b signal gain adustment ;1000:x0~0000:x1 ~0111:x1.875
C r signal offset adjustment at output stage 1000:-8LSB~0000:~ 0111:+7LSB(10bit)
C b signal offset adjustment at output stage 1000:-8LSB~0000:~ 0111:+7LSB(10bit)
Hue adjustmemt ;1000000:-45º~0000000:0º~0111111:+43 6º
Hue Bias adjustmemt ; 000000:0º~111111+45º
Adjustment for the sensitivity of killer detect ratio ; 000:40dB~111:-30dB
LSB Process at SRC Block
Alignment & Adjustment
www.fieldtechsource.net
3-9