Related Manuals for Jonsered CC2036
Summary of Contents for Jonsered CC2036
- Page 1 GR2036 CC2036 Operator’ s manual (EPA) English Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine.
-
Page 2: Key To Symbols
Symbols WARNING! Clearing saws, brushcutters and trimmers can be dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. Please read the operator’s manual carefully and make sure you understand the instructions before... -
Page 3: Table Of Contents
It is extremely important that you read and understand the contents of this operator’s manual. JONSERED HUSKVARNA SWEDEN IMPORTANT ENGINE INFORMATION THIS ENGINE CONFORMS TO U.S. FOR SMALL NON - ROAD ENGINES. -
Page 4: Introduction
Good luck on using your Jonsered machine! Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. -
Page 5: What Is What
What is what? Blade Grease filler cap, bevel gear Bevel gear Cutting attachment guard Shaft Handlebar Throttle control Stop switch Throttle lockout 10 Support eyes for harness 11 Cylinder cover 12 Starter handle 13 Fuel tank 14 Choke control 15 Air purge WHAT IS WHAT? 16 Air filter cover 17 Handle adjustment... -
Page 6: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Important IMPORTANT! The machine is only designed for trimming grass, grass clearing and/or forestry clearing. The only accessories you can operate with this engine unit are the cutting attachments we recommend in the chapter on Technical data. Never use the machine if you are tired, if you have drunk alcohol, or if you are taking medication that could affect your vision, your judgement or your co-ordination. -
Page 7: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS BOOTS Wear boots with steel toe-caps and non-slip sole. CLOTHING Wear clothes made of a strong fabric and avoid loose clothing that can catch on twigs and branches. Always wear heavy, long pants. Do not wear jewellery, shorts sandals or go barefoot. - Page 8 GENERAL SAFETY PRECAUTIONS be checked. See instructions under the heading Maintenance. Stop switch Use the stop switch to switch off the engine. Start the engine and make sure the engine stops when you move the stop switch to the stop setting. Cutting attachment guard This guard is intended to prevent loose objects from being thrown towards the operator.
- Page 9 GENERAL SAFETY PRECAUTIONS saw. Certain harnesses also have a quick release fitted to the support hook. Check that the harness straps are correctly positioned. Once the harness and machine have been adjusted, check that the harness quick release works correctly. Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.
-
Page 10: Cutting Equipment
GENERAL SAFETY PRECAUTIONS should operate the socket spanner when loosening or tightening the nut. The nylon lining inside the locking nut must not be so worn that you can turn it by hand. The lining should offer a resistance of at least 1.5 Nm. The nut should be replaced after it has been put on approx. -
Page 11: Sharpening Grass Cutters And Grass Blades
GENERAL SAFETY PRECAUTIONS Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced. Sharpening grass cutters and grass blades • See the cutting attachment packaging for correct sharpening instructions. Sharpen blades and cutters using a single-cut flat file. •... -
Page 12: Trimmer Head
GENERAL SAFETY PRECAUTIONS Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size. -
Page 13: Assembly
Fitting the handlebar • Remove the screw at the rear of the throttle handle. • Slide the throttle handle onto the right side of the handlebar, (see diagram). • Align the screw hole in the throttle handle with the hole in the handlebar. -
Page 14: Fitting Blades And Trimmer Heads
Fitting blades and trimmer heads WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. -
Page 15: Fitting The Trimmer Guard And Trimmer Head Trimmy Sii
CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data. • Fit the drive disc (B) on the output shaft. • Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. -
Page 16: Fitting Other Guards And Cutting Attachments
Fitting other guards and cutting attachments • Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. CAUTION! Ensure that the guard extension is fitted. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. - Page 17 Correct height Forestry clearing Adjust the support strap so that the support hook is around 10 cm below your hip. The blade should be angled forward a little. Grass clearing The support hook should hang around 20 cm below your hip so that the blade is parallel to the ground. Correct balance Forestry clearing Move the suspension ring on the machine forward or...
-
Page 18: Fuel Handling
When working at continuous high revs a higher octane rating is recommended. Two-stroke oil • For best results and performance use JONSERED two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. • Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). -
Page 19: Fueling
Mixing • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture. Add the remaining amount of gasoline. -
Page 20: Starting And Stopping
Check before starting For safety reasons follow these recommendations! • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. - Page 21 Primer bulb: Press the air purge repeatedly until fuel begins to fill the bulb. The bulb need not be completely filled. Warm engine Ignition: Set the stop switch to the start position. Choke: Set the throttle to the start position by moving the choke control to the choke position and then returning it to its original position.
-
Page 22: Working Techniques
General working instructions IMPORTANT! This section describes the basic safety precautions for working with clearing saws and trimmers. If you encounter a situation where you are uncertain how to proceed you should ask an expert. Contact your dealer or your service workshop. Avoid all usage which you consider to be beyond your capability. - Page 23 The ABC of clearing • Always use the correct equipment. • Make sure the equipment is well adjusted. • Follow the safety precautions. • Organise your work carefully. • Always use full throttle when starting to cut with the blade. •...
- Page 24 conditions, so that cleared stems fall in the cleared area of the stand. Forestry clearing using a saw blade • The risk of blade thrust increases with increasing stem size. You should therefore avoid cutting with the area of the blade between 12 o’clock and 3 o’clock. •...
- Page 25 Brush cutting with a saw blade • Thin stems and brush are mown down. Work with a sawing movement, swinging sideways. • Try to cut several stems in a single sawing movement. • With groups of hardwood stems, first clear around the group.
- Page 26 Cutting • The trimmer is ideal for cutting grass that is difficult to reach using a normal lawn mower. Keep the cord parallel to the ground when cutting. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool.
-
Page 27: Maintenance
Carburetor Your Jonsered product has been designed and manufactured to specifications that reduce harmful exhaust fumes. The engine will be run in after it has used 8-10 tanks of fuel. To ensure that the engine runs at peak performance and produces as little harmful exhaust... - Page 28 Low speed jet L Try to find the highest idling speed, turning the low speed needle L clockwise respectively counter-clockwise. When the highest speed has been found, turn the low speed needle L 1/4 turn counter-clockwise. CAUTION! If the cutting attachment rotates when the engine is idling the idle adjustment screw T should be turned anti-clockwise until the cutting attachment stops.
-
Page 29: Muffler
this screw (4 mm Allen screw) to increase or decrease the start throttle speed. 4 mm Proceed as follows: Run the machine at idle. Press the start throttle lock as described under the heading Starting and stopping. If the start throttle speed is too low (below 4000 rpm), turn the adjuster screw A clockwise until the cutting attachment starts to rotate. -
Page 30: Bevel Gear
Use of the wrong spark plug can damage the piston/ cylinder. Check that the spark plug is fitted with a suppressor. Note: Use only JONSERED replacement parts. Use of other brands of replacement parts can cause damage to your unit or injury to the operator or others. Your... -
Page 31: Maintenance Schedule
Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this manual. More extensive work must be carried out by an authorised service workshop. -
Page 32: Technical Data Technical Data
Technical data Technical data Engine Cylinder displacement, cu.in/cm Cylinder bore, inch/mm Stroke, inch/mm Idle speed, rpm Recommended max. speed, rpm Speed of output shaft, rpm Max. engine output, acc. to ISO 8893, kW/ rpm Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug... - Page 33 Approved accessories Centre hole in blades/cutters, Ø 25,4 mm Output shaft thread M12 Grass blade/grass cutter Saw blade Plastic blades Trimmer head Support cup TECHNICAL DATA Type Multi 255-3 (Ø 255 3 teeth) Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Scarlet 200-22 (Ø...
-
Page 34: Federal Emission Control Warranty Statement Your Warranty Rights And Obligations
As the small nonroad engine owner, you should, however, be aware that Jonsered may deny you warranty coverage if your small nonroad engine or a part of it has failed due to abuse, neglect, improper maintenance, unapproved modifications or the use of parts not made or approved by... - Page 35 FEDERAL EMISSION CONTROL WARRANTY STATEMENT EMISSION CONTROL WARRANTY PARTS LIST Carburetor and internal parts Intake pipe, airfilter holder and carburetor bolts. Airfilter and fuelfilter covered up to maintenance schedule. Ignition System 1Spark Plug, covered up to maintenance schedule 2Ignition Module Muffler with catalytic converter MAINTENANCE STATEMENT The owner is responsible for the performance of all...
- Page 36 Poly Trim <20mm >20mm 6 Nm X 10...
- Page 37 Tap n’ Go 35 Spin 15 cm 6" 8,5 m 10 cm 4" 4,3 m "Clic"...
- Page 38 Tap n’Go 45 Spin 15 cm 6" 10 m 10 cm 4" 4,3 m "Clic"...
- Page 39 Trimmy SII ~ 15 cm 35-50 NM 7,0 m 12 cm 5" ~ 3,5 m "Clic"...
- Page 44 1151201-95 ´®z+S43¶5Z¨ ´®z+S43¶5Z¨ 2008-10-16...