Related Manuals for Jonsered BB2250
Summary of Contents for Jonsered BB2250
- Page 1 Operator’s manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Original Instructions English 115 32 10-26...
- Page 2 (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility that the blowers Jonsered BB2250 with serial numbers dating 2009 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S DIRECTIVE:...
-
Page 3: Table Of Contents
Contents Safety ..............4 SAFETY FIRST . -
Page 4: Safety
• Approved eye protection This product is in accordance with applicable EC directives. Always wear protective gloves. The blower can forcibly throw objects that can bounce back. This can result in serious eye injuries if the recommended safety equipment is not used. -
Page 5: Symbols On The Machine
It is extremely important that you read and understand the contents of this Operator’s manual. 10. Jonsered has a policy of continuous product development and therefore reserves the right to modify the design and appearance of products without prior notice. -
Page 6: Working Conditions
English WORKING CONDITIONS 1. Refrain from operating the blower if you are tired, ill, or upset, or if you are under the influence of alcohol, drugs or medication 2. To reduce the risk of hearing loss associated with sound levels, hearing protection is required. -
Page 7: Using The Product
While using the product, if abnormal noise or vibration occurs, stop the engine immediately and contact the near- est Jonsered servicing dealer for assistance. Checking the fan is very important. If the rotating fan should break up, it might lead to serious accidents. -
Page 8: Maintenance
5. When replacing the any other part or any lubricant, always be sure to use only Jonsered products or products which have been certified by Jonsered for use with the Jonsered product. 6. In the event that any part must be replaced or any... -
Page 9: What Is What
<BB2250> 1. Frame 2. Harness 3. Engine Cover 4. Volute Case, Cover 5. Net 6. Air Cleaner 7. Recoil Starter 8. Fuel Tank 9. Spark Plug Cap 10.Choke Lever 11. Control handle 12. Stop Switch DISPOSAL When disposing your machine, do not disassemble the machine. -
Page 10: Technical Data
Note 3: The equivalent vibration total value is calculated with a work cycle of a duration of 1/7 for idling and 6/7 for racing. Reported data for equivalent vibration level has a typical statistical dispersion (standard deviation) of 1 m/s Technical data Air cooled 2-cycle gasoline engine ) in conformity with EC directive 2000/14/EC. Reported sound BB2250 401x460x495 10.1 50.2 Half wet urethane... -
Page 11: Assembly
FLEXIBLE HOSE AND SWIVEL JOINT 1. Connect the blower and swivel joint with flexible hose. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. (1) Flexible hose (2) Swivel joint (3) clamp (large) (4) Clamp (small) NOTE A light lubricant may be used to ease assembly of flexible hose to blower tube. -
Page 12: Fuel
• The engines are lubricated by oil specially formulated for air-cooled 2-cycle gasoline engine use. If Jonsered oil is not available, use an anti-oxidant added quality oil expressly labeled for air-cooled 2- cycle engine use. (JASO FC GRADE OIL or ISO EGC GRADE) •... -
Page 13: Operation
(2) About 1/3 Open (3) Idling (4) Stop switch 5. To start, hold the top of the blower firmly with your left hand. Pull the starter knob slowly until you feel it engage and then give it a vigorous strong pull. IMPORTANT •... -
Page 14: Adjusting Idle Speed
English ADJUSTING IDLE SPEED • The idling speed is set for 2000 rpm at the factory. If it is necessary to adjust the idle speed, use the adjustment screw on the top side of carburetor. (1) Idling Adjustment Screw STOPPING ENGINE •... -
Page 15: Maintenance
A clogged air filter may increase fuel consumption while cutting down the engine power. • Never operate the blower without an air filter or with a deformed or broken filter element because unfiltered dusty air will quickly ruin the engine. -
Page 16: Spark Plug
WARNING • Periodically inspect the muffler for loose fasteners, damage or corrosion. If any sign of exhaust leakage is found, do not use the blower and have it repaired immediately. 1. Remove the muffler, insert a screwdriver into the vent, and wipe away any carbon buildup. -
Page 17: Air Inlet Net
(1) Net WARNING Never use the blower without the net on the blower. Before each use, check that the net is attached in place and is free from any damage. SHOLDER STRAP • If the shoulder strap is damaged it may break during use, thus causing the product to fall and resulting in personal injury.