Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
Page 2 Contents Before driving Introduction Instrumentation Controls and features Seating and safety restraints Starting and driving Starting Driving Roadside emergencies Servicing Maintenance and care Capacities and specifications Customer assistance Reporting safety defects Index All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company.
Page 3: Introduction
Introduction The following warning may be required by California law: CALIFORNIA Proposition 65 Warning WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
Page 4 Introduction WARNINGS Warnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently. This is recommended to give the moving parts a chance to break in.
Page 5 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Tether Warning Anchorage Brake System Anti-Lock Brake System Brake Fluid - Traction Control...
Page 6 Introduction Vehicle Symbol Glossary Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid Power Steering Fluid Level Emission System...
Page 7: Instrumentation
Instrumentation Instrument cluster Instrument panel (pg. 8) dimmer control (pg. 18) Headlamp control (pg. 17) Trunk release — sedan only (pg. 60) Parking brake release Rear window wiper and (pg. 120) washer — wagon only* Driver air bag (pg. 51) Turn signal and (pg.
Page 8 Instrumentation Electronic sound system (pg. 29) Speed control* (pg. 47) Gearshift Climate control system (pg. 123) (pg. 19)
Page 9 Instrumentation WARNING LIGHTS AND CHIMES – 0 0 0 0 FUEL DOOR > RPMx1000 0 0 0 0 0 0 km/h BRAKE THEFT CRUISE COOLANT R N D D 1 Turn signal Illuminates when the left or right turn signal or the hazard lights are turned on.
Page 10 Instrumentation Safety belt Momentarily illuminates when the ignition is turned to the ON position to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Door ajar Illuminates when the ignition is in the ON position and any door is open.
Page 11 Instrumentation indicator light illuminates when the ignition is first turned to the ON position to check the bulb. If it comes on after the engine is started, one of the engine’s emission control systems may be malfunctioning. The light may illuminate without a driveability concern being noted.
Page 12: Controls And Features
Instrumentation Low fuel Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel gauge in this chapter for more information). When refueling, after the light comes on, the amount of fuel that is added will be less than the advertised capacity since there is fuel still in the tank.
Page 13 Instrumentation Check transaxle Momentarily illuminates when the ignition is turned to the ON position. Illumination of this light indicates that a problem has been detected and shifting may be restricted. If this lamp remains on, have your vehicle serviced immediately. Speed control (if equipped) This light comes on when either the CRUISE...
Page 14: Seating And Safety Restraints
Instrumentation Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly, requiring electrical system service. Air bag readiness Momentarily illuminates when the ignition is turned ON.
Page 15 Instrumentation GAUGES – 0 0 0 0 FUEL DOOR > RPMx1000 0 0 0 0 0 0 km/h BRAKE THEFT CRUISE CRUISE COOLANT R N D D 1 Speedometer Indicates the current vehicle speed. 0 0 0 0 0 0 0 0 0 0 km/h R N D D 1 Tachometer...
Page 16 Instrumentation Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine immediately and let the engine cool.
Page 17 Instrumentation Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or after refueling. The ignition should be in the OFF position while the vehicle is being refueled.
Page 18: Controls And Features
Controls and features HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. Daytime running lamps (DRL) (if equipped) Turns the headlamps on with a reduced output. To activate: •...
Page 19 Controls and features Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on only when the headlamp control is in the position and the high beams are not turned on. Pull headlamp control towards you to turn foglamps on.
Page 20 Controls and features REAR WINDOW DEFROSTER The rear defroster control is located on the instrument panel. Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster.
Page 21 Controls and features Temperature control knob Controls the temperature of the airflow inside the vehicle. Mode selector control Controls the direction of the airflow to the inside of the vehicle. The air conditioning compressor can operate in all modes except However, the air conditioning will only function if the outside temperature is about 6°C (43°F) or...
Page 22: Driving
Controls and features • (Panel and floor)-Distributes outside air through the instrument panel registers and the floor ducts. Heating and air conditioning capabilities are provided in this mode. For added customer comfort, when the temperature control knob is anywhere in between the full hot and full cold positions, the air distributed through the floor ducts will be slightly warmer than the air sent to the instrument panel registers.
Page 23 Controls and features • Under snowy or dirty weather conditions, your vehicle’s climate control system should be left in the OFF position when the vehicle is parked. This allows the climate control system to be free from contamination of outside pollutants. •...
Page 24 Controls and features Electronic Automatic Temperature Control (EATC) system (if equipped) OUTSIDE TEMP AUTO TEMP The EATC system will maintain a selected temperature and automatically control airflow. You can override automatic operation with any of the override controls or the fan speed control. Turning the EATC on OUTSIDE TEMP...
Page 25 Controls and features Automatic operation Press AUTO and select the desired temperature. The selected temperature and the word AUTO will appear in the display window. The EATC system will either heat or cool to achieve the selected temperature. The system will automatically determine fan speed, airflow location and if outside air or recirculated air is required.
Page 26 Controls and features For continuous maximum heating, push the temperature control until 32°C (90°F) is shown in the display window. The EATC will continue maximum heating (disregarding the displayed temperature) until a cooler temperature is selected by pressing the temperature control. Temperature conversion OUTSIDE TEMP...
Page 27 Controls and features Manual override controls OUTSIDE TEMP AUTO TEMP The override controls are located at the bottom of the EATC and allow you to determine where airflow is directed. To return to full automatic control, press AUTO. The air conditioning compressor can operate in all modes except .
Page 28 Controls and features • (Floor)-Allows for maximum heating by distributing outside air through the floor ducts. However, the air cannot be cooled below the outside temperature because the air conditioning does not operate in this mode. • (Panel and floor) -Distributes outside air through the instrument panel registers and the floor ducts.
Page 29 Controls and features Operating tips • In humid weather conditions, place the climate control system in before driving. This will reduce fogging on your windshield. Once the windshield has been cleared, operate the climate control system as desired. • To reduce humidity buildup inside the vehicle in cold weather conditions, don’t drive with the climate control system in the OFF or MAX A/C position.
Page 30 Controls and features Avoid placing small objects on top of the instrument panel. These objects may fall down into the defroster outlets and block airflow, in addition to damaging the climate control system. Do not place objects on top of the instrument panel, as these objects may become projectiles in a collision or sudden stop.
Page 31 Controls and features Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on.
Page 32 Controls and features You can switch from CD play to tape play by simply inserting a tape into the cassette deck. Tune disc adjust The tune control works in radio or CD mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there).
Page 33 Controls and features Seek function in CD mode • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
Page 34 Controls and features 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass/treble adjust • The bass adjust control allows you to increase or decrease the audio system’s bass output.
Page 35 Controls and features • To begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the TAPE control. Press the control during rewind or fast forward to stop the rewind or fast forward function.
Page 36 Controls and features Dolby noise reduction Dolby noise reduction operates only in tape mode. Dolby noise reduction reduces the amount of hiss and static during tape playback. Press the control to activate (and deactivate) Dolby noise reduction. Dolby noise reduction system is manufactured under license from Dolby Laboratories Licensing Corporation.
Page 37 Controls and features Audio System with AM/FM Stereo/Single CD Player Volume/power control Press the control to turn the audio system on or off. Turn control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 38 Controls and features AM/FM select The AM/FM select control works in radio, and CD modes (if equipped). Press the AM or FM control to enter into radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations.
Page 39 Controls and features Seek function The seek function control works in radio or CD mode. Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in CD mode •...
Page 40 Controls and features Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to Tune adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected.
Page 41 Controls and features Speaker balance/fade adjust • Speaker sound distribution can be adjusted between the right and left speakers. • Speaker sound can be adjusted between the front and rear speakers. CD select • Pressing the CD control when the ignition is on will engage the system if a CD is present in the audio system.
Page 42 Controls and features • In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. • You can cancel the fast forward mode by pressing TAPE, or the FF control.
Page 43 Controls and features CD changer (if equipped) Your CD changer is either located in the trunk, the console or the right side cargo area storage compartment. 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3.
Page 44 Controls and features If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder.
Page 45 Controls and features ONLY use the magazine supplied with the CD changer, other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty. Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.
Page 46 Controls and features Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur. Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation.
Page 47 Controls and features • Station overload. Weak signals are sometimes captured by stronger signals when you pass a broadcast tower. A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally received in stereo.
Page 48 Controls and features POSITIONS OF THE IGNITION 1. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF, shuts off the engine without locking the steering wheel.
Page 49 Controls and features To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET+. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30...
Page 50 Controls and features You can accelerate with the accelerator pedal at any time during speed control usage. Releasing the accelerator pedal will return your vehicle to the previously programmed set speed. To set a lower set speed • Press and hold CST −. Release the control when the desired speed is reached or •...
Page 51 Controls and features To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light This light comes on when either the CRUISE SET or RES controls are pressed. It turns off when the speed control OFF control is pressed, the brake is applied or the ignition is turned to the OFF position.
Page 52: Roadside Emergencies
Controls and features Mist Function To operate the Mist function of the windshield wipers, push and release the windshield washer control quickly. The wipers will cycle one or two times. Rear window wiper and washer (wagon only) The rear wiper control is located under the headlamp controls Press the wiper control to activate the rear wiper.
Page 53 Controls and features TILT STEERING Pull the tilt steering control toward you to move the steering wheel up or down. Hold the control while adjusting the wheel to the desired position, then release the control. Never adjust the steering wheel when the vehicle is moving. REPLACING THE INTERIOR BULBS Check the operation of the following interior bulbs frequently: •...
Page 54 Controls and features With the control in the middle position, the dome lamp will illuminate whenever a front door is opened. If either front door has been opened from the outside, the lamp will remain on for 25 seconds after the door is shut.
Page 55 Controls and features ILLUMINATED VISOR MIRROR (IF EQUIPPED) To turn on the visor mirror lamps, lift the mirror cover. Adjust the amount of light by sliding the control. MOON ROOF (IF EQUIPPED) Push up on the control to raise the moon roof to the vent position.
Page 56 Controls and features You will need a Phone Adapter System (PAS) that is compatible with your cell phone that you install into the center console. This system includes a Phone Adapter Module (PAM) with a Wiring Harness and a Hang-Up Cup. For more information, call 1–800–736–9450 to order the Phone Adapter System (PAS) for your specific phone.
Page 57 Controls and features POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. AUTO • Press the bottom portion of the rocker switch to open. AUTO One touch down •...
Page 58 Controls and features Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls except for the driver’s press the left side of the control. Press the right side to restore the window controls. Accessory delay (if equipped) With accessory delay, the window switches may be used for up to ten minutes after the ignition switch is turned to the OFF position or until...
Page 59 Controls and features POWER SIDE VIEW MIRRORS To adjust your mirrors: 1. Select to adjust the left mirror or to adjust the right mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to disable adjust function. Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist...
Page 60 • Compact disc changer (if equipped) • Tissue holder • Rear A/C vent • Rear ashtray (see your Ford, Lincoln Mercury dealer to obtain rear ashtray Use only soft cups in the cupholder. Hard objects can injure you in a collision.
Page 61 Controls and features TRUNK REMOTE CONTROL Press the remote trunk release control on the instrument panel to the left of the steering wheel. LIFTGATE (WAGON ONLY) You can open and close the liftgate and the liftgate window from outside the vehicle. It cannot be opened from inside the cargo area. •...
Page 62 Controls and features CARGO AREA FEATURES Storage compartment Your vehicle comes equipped with a storage compartment in the floor of the cargo area. An additional compartment is in the rear trim panel on the right. Always put the load you are carrying as far forward as possible.
Page 63 Controls and features To prevent the possibility of injuries, the fasteners for the cargo area cover must be properly attached to the mounting clips on the rear trim panels. Do not place any objects on the cargo area cover. They may obstruct your vision or strike occupants of the vehicle in the case of a sudden stop or collision.
Page 64 Controls and features 4. Push in the right end cap (marked RH) about ⁄ of the total length to disengage the clutch and hold the end cap in while turning the roller tube toward you 14 times. 5. Let go of the right end cap. The clutch will now engage and stop the shade from losing its spring tension.
Page 65 Controls and features Unlocking the doors/liftgate Press this control to unlock the driver’s door. The interior lamps will illuminate with the ignition OFF. Press the control a second time within three seconds to unlock all doors and liftgate (wagons). Locking the doors/liftgate Press this control to lock all doors and liftgate (wagons).
Page 66 Controls and features Sounding a panic alarm Press this control to activate the alarm. To deactivate the alarm, press the control again or turn the ignition to ACC or ON. Illuminated entry The interior lamps illuminate when the remote entry system is used to unlock the door(s).
Page 67 Controls and features Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Place the key in the ignition and turn from 2 (LOCK) to 3 (OFF) and cycle between 3 (OFF) and 4(ON) eight times in rapid...
Page 68 Controls and features To replace the battery: 1. Twist a thin coin between the two halves of the transmitter near the key ring. DO NOT TAKE THE FRONT PART OF THE TRANSMITTER APART. 2. Place the positive (+) side of new battery in the same orientation.
Page 69 Controls and features • Press 7/8 and 9/0 controls on the keyless entry pad at the same 7 8 9 0 time to lock the doors (doors opened or closed). • Open a door and press the power door lock control to lock the doors. There is a 20 second countdown when any of the above actions occur before the vehicle becomes ARMED.
Page 70 Controls and features • Unlock the doors by using your keyless entry pad. 7 8 9 0 • Unlock the doors or liftgate with a key. Turn the key full travel (toward the front of the vehicle) to make sure the alarm disarms. •...
Page 71 Controls and features The factory-set code is located: • on the owner’s wallet card in the glove compartment • taped to the computer module • or at your dealer When pressing the controls on the keyless entry keypad, press the middle of the controls to ensure a good activation.
Page 72 Controls and features Unlocking the doors and releasing the trunk with the keyless entry system The driver’s door must be unlocked before any other. If more than five seconds pass between pressing numbers, enter the code again. The system has shut down if the keypad light is out. If the keyless entry system does not work, use the key or remote entry transmitter(s).
Page 73 Controls and features Deactivating/activating autolock There are 2 methods to enable/disable this feature. One through your dealer and the second with a door lock sequence using the following instructions: 1. Turn the ignition key to RUN, then press the door UNLOCK control button 3 times.
Page 74 Controls and features SECURILOCK PASSIVE ANTI-THEFT SYSTEM SecuriLock passive anti-theft system is an engine immobilization system. This system prevents the engine from being started unless a coded key programmed to your vehicle is used. The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems.
Page 75 Controls and features The SecuriLock passive anti-theft system is not compatible with non-Ford (aftermarket) remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Large metallic objects, electronic devices on the key chain that can be used to purchase gasoline or similar items, or a second key on the same key ring as the coded key ignition...
Page 76 Controls and features Programming spare keys A maximum of eight keys can be coded to your vehicle. Only SecuriLock keys can be used. To program a coded key yourself, you will need two previously programmed coded keys (keys that already operate your vehicle’s engine) and the new unprogrammed key(s) readily accessible for timely implementation of each step in the procedure.
Page 77 Controls and features INTERIOR LUGGAGE COMPARTMENT RELEASE Your vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape for children and adults in the event they become locked inside the luggage compartment. Adults are advised to familiarize themselves with the operation and location of the release handle.
Page 78: Seating And Safety Restraints
Seating and safety restraints SEATING Adjustable head restraints Your vehicle’s seats are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. To properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to that position as possible.
Page 79 Seating and safety restraints Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. Lift handle to move seat forward or backward.
Page 80 Seating and safety restraints Reclining the seatback can reduce the effectiveness of the seat’s safety belt in the event of a collision. The control is located on the outboard side of the seat cushion. Press front to raise or lower the front portion of the seat cushion.
Page 81 Seating and safety restraints REAR SEATS 2nd seat/Split-folding rear seat (if equipped) One or both rear seatbacks can be folded down to provide additional cargo space. To lower the seatback(s) from inside the vehicle, pull tab to release seat back and then fold seatback down.
Page 82 Seating and safety restraints 3. Lift the remote latch release on the left side of the compartment and fold the remaining floor panel until it latches. Make sure the seatback is locked in the upright position. To close the seat, make sure the safety belts are properly stowed, then lift the remote latch release and push the seat down until it latches.
Page 83 Seating and safety restraints How does the personal safety system work? The Personal Safety System uses a collection of sensors to gather information about the driver’s seat position, driver and front outboard passenger’s safety belt usage and accident severity. Then, dual-stage inflating air bags are combined with safety belt pretensioners and energy management retractors to help provide enhanced occupant protection in frontal crashes.
Page 84 Seating and safety restraints • A series of five beeps will be heard. The tone pattern will repeat periodically until the problem and indicator light are repaired. If any of these things happen, even intermittently, have the Personal Safety System serviced at your dealership or by a qualified technician immediately.
Page 85 Seating and safety restraints It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts.
Page 86 Seating and safety restraints 2. To unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: Energy management retractors Your vehicle has a seat belt system equipped with energy management...
Page 87 Seating and safety restraints BELT AND RETRACTOR ASSEMBLY MUST BE REPLACED if the seat belt assembly “automatic locking retractor” feature or any other seat belt function is not operating properly when checked according to the procedures in Workshop Manual. Failure to replace the Belt and Retractor assembly could increase the risk of injury in collisions.
Page 88 Seating and safety restraints How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound.
Page 89 Seating and safety restraints After any vehicle collision, the front passenger outboard seat belt system must be checked by a qualified technician to verify that the “automatic locking retractor” feature for child seats is still functioning properly. In addition, all seat belts should be checked for proper function.
Page 90 Seating and safety restraints The Personal Safety System provides the most benefit to belted occupants. The system monitors and tailors the air bag deployment based upon safety belt usage. Failure to properly wear your safety belt will increase your risk of injury. Front safety belt height adjustment Your vehicle has safety belt height adjustments for the driver and front...
Page 91 Seating and safety restraints Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). To lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle.
Page 92 Seating and safety restraints To fasten the belt, pull the combination lap and shoulder belt from the retractor so that the shoulder belt portion of the safety belt crosses your shoulder and chest. Be sure the belt is not twisted. If the belt is twisted, remove the twist.
Page 93 Seating and safety restraints the label. Also, use the safety belt extension only if the safety belt is too short for you when fully extended. Do not use extensions to change the fit of the shoulder belt across the torso. Safety belt warning light and indicator chime The seat belt warning light illuminates in the instrument cluster and a chime sounds to remind the occupants to fasten their safety belts.
Page 94 Seating and safety restraints If... Then... The driver’s safety belt is not The Belt Minder feature is buckled before the vehicle has activated - the safety belt warning reached at least 5 km/h (3 mph) light illuminates and the warning and 1-2 minutes have elapsed chime sounds for 6 seconds every since the ignition switch has been...
Page 95 Seating and safety restraints Reasons given... Consider... “Belts wrinkle my Possibly, but a serious crash can do much more clothes” than wrinkle your clothes, particularly if you are unbelted. “The people I’m Set the example, teen deaths occur 4 times more with don’t wear often in vehicles with TWO or MORE people.
Page 96 Seating and safety restraints • the parklamps/headlamps are in OFF position (If vehicle is equipped with Autolamps, this will not affect the procedure.) To reduce the risk of injury, do not deactivate/activate the Belt Minder feature while driving the vehicle. 1.
Page 97 Seating and safety restraints there are no nicks, wears or cuts. Replace if necessary. All safety belt assemblies, including retractors, buckles, front seat belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seatback (if equipped), child safety seat tether bracket assemblies (if equipped), LATCH child seat tether anchors and lower anchors (if equipped), and attaching hardware, should be inspected after a collision.
Page 98 Seating and safety restraints The air bag supplemental restraint system is designed to work in conjunction with the safety belts to help protect the driver and front outboard passenger from certain upper body injuries. The term “supplemental restraint” means the air bags are intended as a supplement to the safety belts.
Page 99 Do not attempt to service, repair, or modify the Air Bag Supplemental Restraint System or its fuses. See your Ford or Lincoln Mercury dealer. Modifications to the front end of the vehicle, including frame, bumper, front end body structure and tow hooks may effect the performance of the air bag sensors increasing the risk of injury.
Page 100 Seating and safety restraints Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position.
Page 101 Seating and safety restraints How do the air bag supplemental restraints work? The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking...
Page 102 Do not attempt to service, repair, or modify the air bag Supplemental Restraint System, its fuses or the seat cover on a seat containing an air bag. See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 103 Seating and safety restraints How does the side air bag system work? The side air bag system consists of the following: • An inflatable nylon bag (air bag) with a gas generator concealed behind the outboard bolster of the driver and front passenger seatbacks.
Page 104 Seating and safety restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the side air bag has deployed, the air bag will not function again. The side air bag system (including the seat) must be inspected and serviced by a qualified technician in accordance with...
Page 105 Seating and safety restraints Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision. Always follow the instructions and warnings that come with any infant or child restraint you might use.
Page 106 Seating and safety restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 107 Seating and safety restraints Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position which is capable of providing a tether anchorage. For more information on top tether straps, refer to Attaching safety seats with tether straps.
Page 108 Seating and safety restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 109 Seating and safety restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 110 Seating and safety restraints Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. To lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing.
Page 111 Seating and safety restraints Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor. 1. Position the child safety seat on the seat cushion. 2.
Page 112 Seating and safety restraints If the safety seat is not anchored properly, the risk of a child being injured in a collision greatly increases. Attaching child safety seats with LATCH attachments for child seat anchors Some child safety seats are labeled as LATCH or LATCH-compatible child seats.
Page 113 Seating and safety restraints The lower anchors for child seat installation are located at the rear section of the rear seat between the cushion and seat back. Your vehicle may have symbols near the bottom of the rear seat back. Each lower anchor for child seat installation is located 2–3 inches below the locator symbols.
Page 114 Starting PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting.
Page 115 Starting 2. Make sure the headlamps and vehicle accessories are off. 3. Make sure the gearshift is in P P R N (Park). 4. Make sure the parking brake is set. 5. Turn the key to 4 (ON) without turning the key to 5 (START). If there is difficulty in turning the key, firmly rotate the steering wheel left and right until the key turns...
Page 116 Starting – 0 0 0 0 FUEL DOOR > RPMx1000 0 0 0 0 0 0 km/h BRAKE THEFT CRUISE COOLANT R N D D 1 Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. •...
Page 117 Starting Using the engine block heater (if equipped) An engine block heater warms the engine coolant, which improves starting, warms up the engine faster and allows the heater-defroster system to respond quickly. Use of an engine block heater is strongly recommended if you live in a region where temperatures reach -23°C (-10°F) or below.
Page 118 Starting Important ventilating information If the engine is idling while the vehicle is stopped in an open area for long periods of time, open the windows at least 2.5 cm (one inch). Adjust the heating or air conditioning (if equipped) to bring in fresh air. Improve vehicle ventilation by keeping all air inlet vents clear of snow, leaves and other debris.
Page 119 Driving BRAKES Your service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the brakes are applied.
Page 120 Driving ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. With the ABS light on, the anti-lock brake system is disabled and normal braking is still effective unless the...
Page 121 Driving Parking brake Apply the parking brake whenever the vehicle is parked. To set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the BRAKE ignition is turned ON) until the parking brake is released.
Page 122 Driving Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy. TRACTION CONTROL (IF EQUIPPED) Your vehicle may be equipped with the optional Traction Control system.
Page 123 Driving the engine compartment and the engine will not “rev-up” when you push further on the accelerator. This is normal system behavior. The Traction Control on/off switch, located on the right side of the instrument cluster, illuminates OFF when the system is turned OFF.
Page 124 Driving AUTOMATIC TRANSAXLE OPERATION Brake-shift interlock This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed: 1.
Page 125 Driving If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly. See your dealer or a qualified service technician. Driving with an automatic overdrive transaxle Your automatic transaxle electronically controls the shift feel by using an adaptive learning strategy.
Page 126 Driving Understanding gearshift positions P (Park) Always come to a complete stop P R N before shifting into P (Park). Make sure the gearshift lever is securely latched in P (Park). This locks the transaxle and prevent the front wheels from rotating. Always set the parking brake fully and make sure the gearshift is latched in P...
Page 127 Driving N (Neutral) With the gearshift lever in the N P R N (Neutral) position, the vehicle can be started and is free to roll. Hold the brake pedal down while in this position. (Overdrive) (Overdrive) position is the P R N normal driving position for an automatic overdrive transaxle.
Page 128 Driving When to use D (Drive) The D (Drive) position eliminates P R N the needless shifting back and forth between third and fourth gears that your vehicle may do when driving on hilly terrain. It also gives more engine braking than overdrive to slow your vehicle on downgrades.
Page 129 Driving When parking, do not use the gearshift in place of the parking brake. Always set the parking brake fully and make sure that the gearshift is securely latched in Park (P). Turn off the ignition whenever you leave your vehicle. Never leave your vehicle unattended while it is running.
Page 130 Driving • Maximum Trailer Weight: Maximum weight of a trailer the loaded vehicle (including passengers and cargo) is permitted to tow. It is determined by subtracting the weight of the loaded trailer towing vehicle from the GCWR for the towing vehicle. •...
Page 131 Your vehicle does not come from the factory fully equipped to tow. No towing packages are available through Ford or Mercury/Lincoln dealers. Do not tow a trailer until your vehicle has been driven at least 800 km (500 miles). If towing with a station wagon, inflate the rear tires to 35 psi.
Page 132 Driving 3.0L 4-Valve Duratec Engine Model Passenger Load - Luggage Load - Max Trailer Wt.- #/kg (lbs.) kg (lbs.) kg (lbs.) Sedan 5/340 (750) 590 (1 300) 2/135 (300) 70 (150) 725 (1 600) 2/135 (300) 795 (1 750) Wagon 5/340 (750) 70 (150) 455 (1 000)
Page 133 Driving Trailer brakes Electric brakes and manual, automatic or surge-type trailer brakes are safe if installed properly and adjusted to the manufacturer’s specifications. The trailer brakes must meet local and Federal regulations. Do not connect a trailer’s hydraulic brake system directly to your vehicle’s brake system.
Page 134 Driving • The trailer tongue weight should be 10% of the loaded trailer weight. • After you have traveled 80 km (50 miles), thoroughly check your hitch, electrical connections and trailer wheel lug nuts. • When stopped in traffic for long periods of time in hot weather, place the gearshift in P (Park) and increase idle speed.
Page 135 Driving LUGGAGE RACK (IF EQUIPPED) The rear crossbar can be adjusted to fit the item being carried. The front crossbar does not move. Do not load more than 44 kg (100 lbs.) on the luggage rack. To adjust cross-bar position: 1.
Page 136: Roadside Emergencies
In the United States, this card is found in the Owner Guide portfolio in the glove compartment in Ford vehicles and is mailed to you if you own a Mercury or Lincoln. In Canada, the card is found in the Roadside Assistance book in the glove compartment.
Page 137 In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer. Similarly in Canada, you may purchase additional coverage beyond the basic coverage period by consulting the Ford Roadside Assistance Club brochure or by calling 1–877–294–CLUB (1–877–294–2582).
Page 138 Roadside emergencies If your vehicle is a sedan, the fuel pump shut-off switch is located on the right side of the trunk behind the trunk liner. If your vehicle is a wagon, the fuel pump shut-off switch is located behind the service panel on the right side of the cargo area.
Page 139 Roadside emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. NOTE: Always replace a fuse with one that has the specified amperage rating.
Page 140 Roadside emergencies Passenger compartment fuse panel The fuse panel is located below and to the left of the steering wheel by the brake pedal. Remove the panel cover to access the fuses. To remove a fuse use the fuse puller tool provided on the fuse panel cover.
Page 141 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Cigar Lighter — Not Used Front Wiper Motor Flasher and GEM Power, Integrated Control Panel (ICP) Power, RCC Memory, Cluster Stop Lamp, Speed Control Deactivating Switch — Not Used —...
Page 142 Roadside emergencies Fuse/Relay Fuse Amp Passenger Compartment Location Rating Fuse Panel Description Transmission Position Switch GEM Park Neutral Switch — Not Used — Not Used — Not Used — Not Used Power distribution box The power distribution box is located in the engine compartment. The power distribution box contains high-current fuses that protect your vehicle’s main electrical systems...
Page 143 Roadside emergencies The high-current fuses are coded as follows. Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 60A** Fuse Junction Panel 30A** PCM Relay 60A** Fuse Junction Panel — Not Used — Not Used — Not Used 40A** Starter Relay, Ignition Switch 20A** Transit Relay (Export only) 40A**...
Page 144 Roadside emergencies Fuse/Relay Fuse Amp Power Distribution Box Description Location Rating 15A* Left Headlamp 10A* A/C Clutch Relay, PCM Keep Alive Power — Starter Motor Relay — Low Speed Fan Relay — Wiper Speed Relay 10A* Generator Rear Control Unit, Antenna 15A* HEGO Sensor Transmission Shift Solenoid, Canister Vent, A/C Clutch Relay,...
Page 145 Roadside emergencies When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • tow a trailer • use tire chains •...
Page 146 Roadside emergencies • In the sedan, these are located in the trunk cargo area storage compartment. • In the wagon, they are stored in the left side rear trim panel for the temporary spare and in the floor cargo area storage compartment for the full size spare.
Page 147 Roadside emergencies 5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. 6. Put the jack in the jack notch next to the door of the tire you are changing.
Page 148 Roadside emergencies 11. Return the flat tire, jack and lug wrench to their proper storage locations. Make sure the jack is fastened so it does not rattle when you drive. 12. Unblock the wheels. JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes.
Page 149 Roadside emergencies 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts.
Page 150 Roadside emergencies 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery. 4. Make the final connection of the negative (-) cable. Make the connection to an exposed metal part of the stalled vehicle’s engine, away from the battery and the carburetor/fuel injection system.
Page 151 Roadside emergencies Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables.
Page 152 Roadside emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 153 Roadside emergencies WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or, if you are a member, your roadside assistance center. It is recommended that your vehicle be towed with a wheel lift or flatbed equipment.
Page 154: Maintenance And Care
Maintenance and care SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 155 Maintenance and care Do not start your engine with the air cleaner removed and do not remove it while the engine is running. OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2.
Page 156 Maintenance and care IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 3.0L V6 Vulcan engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil filler cap 6. Engine oil dipstick 7. Power steering fluid reservoir 8.
Page 157 Maintenance and care 3.0L DOHC V6 Duratec engine 1. Automatic transmission fluid dipstick 2. Brake fluid reservoir 3. Air filter assembly 4. Battery 5. Engine oil filler cap 6. Engine oil dipstick 7. Engine coolant reservoir 8. Windshield washer fluid reservoir 9.
Page 158 Maintenance and care ENGINE OIL Checking the engine oil Refer to the scheduled maintenance guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. Turn the engine off and wait a few minutes for the oil to drain into the oil pan.
Page 159 Maintenance and care • If the oil level is below the add 1QT or MIN mark, add enough oil to raise the level within the 1QT-FULL or the MIN-MAX range (depending on application). • Oil levels above the F in FULL or above the MAX mark, may cause engine damage.
Page 160 Maintenance and care Engine oil and filter recommendations Look for this certification trademark. SAE 5W-20 engine oil is recommended. Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). Use Motorcraft or an equivalent oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Page 161: Capacities And Specifications
Maintenance and care BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the scheduled maintenance guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir.
Page 162 Maintenance and care WINDSHIELD WASHER FLUID Washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low, add enough fluid to fill the reservoir. In very cold weather, do not fill the reservoir all the way.
Page 163 Maintenance and care Checking and adding washer fluid for the liftgate (if equipped) The opening for the reservoir is located on the passenger side under the tail lamp. Refill this reservoir with the same fluid you use for your windshield. ENGINE COOLANT Checking engine coolant Your vehicle was factory-filled with a 50/50 engine coolant and water...
Page 164 Maintenance and care When the engine is cold, check the level of the engine coolant in the reservoir. • The engine coolant should be at the “cold fill level” or within the “cold fill range” as listed on the engine coolant reservoir (depending upon application).
Page 165 Maintenance and care • DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). • DO NOT USE a DEX-COOL engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44-D. • DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze.
Page 166 Maintenance and care Check the coolant level in the reservoir before you drive your vehicle the next few times (with the engine cool). If necessary, add a 50/50 mixture of engine coolant and distilled water to the engine coolant reservoir until the coolant level is at the “cold fill level” or within the “cold fill range”...
Page 167 Maintenance and care Fill your engine coolant reservoir as outlined in Adding engine coolant in this chapter. Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • it may be necessary to increase the coolant concentration above 50%.
Page 168 Maintenance and care CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only MERCON ATF. 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).
Page 169 Maintenance and care 5. If the fluid is low, add fluid in small amounts, continuously checking the level until it reaches the FULL HOT range. Be sure to put the dipstick back in the reservoir. 3.0L DOHC V6 Duratec engine 4.
Page 170 Maintenance and care 3. With the parking brake engaged and your foot on the brake pedal, start the engine and move the gearshift lever through all of the gear ranges. Allow sufficient time for each gear to engage. 4. Latch the gearshift lever in P (Park) and leave the engine running. 5.
Page 171 Maintenance and care Use of a non-approved automatic transmission fluid may cause internal transaxle component damage. If necessary, add fluid in 250 mL (1/2 pint) increments through the filler tube until the level is correct. If an overfill occurs, excess fluid should be removed by a qualified technician.
Page 172 Maintenance and care The filter is located just in front of the windshield under the cowl grille on the passenger side of the vehicle. 1. Release and open the hood. 2. Remove the four clips located on the cowl vent screen.
Page 173 Maintenance and care 3. Remove the cowl vent screen. 4. Remove the two screws retaining the cowl top inner panel shield. 5. Remove the inner panel shield.
Page 174 Maintenance and care 6. Remove the filter from the cabin air filter housing. 7. Install the new cabin air filter into the cabin air filter housing.
Page 175 Maintenance and care 8. Replace the inner panel shield. 9. Replace the two screws retaining the cowl top inner panel shield. 10. Replace the cowl vent screen.
Page 176 Maintenance and care 11. Replace the four clips located on the cowl vent screen. BATTERY Your vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However, for severe usage or in high temperature climates, check the battery electrolyte level.
Page 177 Maintenance and care If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer, trouble-free operation, keep the top of the battery clean and dry. Also, make certain the battery cables are always tightly fastened to the battery terminals.
Page 178 Maintenance and care 2. Put the gearshift in P (Park), turn off all accessories and start the engine. 3. Run the engine until it reaches normal operating temperature. 4. Allow the engine to idle for at least one minute. 5. Turn the A/C on and allow the engine to idle for at least one minute. 6.
Page 179 Maintenance and care Changing the wiper blades To replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. Turn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the...
Page 180 Maintenance and care U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course.
Page 181 Maintenance and care The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure •...
Page 182 Maintenance and care Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification or Tire Label.
Page 183 Maintenance and care Follow these guidelines when using snow tires and chains: • Use only cable type chains offered by Ford as an accessory or equivalent. SAE class “S” or other conventional link type chains may cause damage to the vehicle’s wheel house and/or body. •...
Page 184 Maintenance and care Gasoline may contain benzene, which is a cancer-causing agent. Observe the following guidelines when handling automotive fuel: • Extinguish all smoking materials and any open flames before fueling your vehicle. • Always turn off the vehicle before fueling.
Page 185 Maintenance and care When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke while refueling. Fuel vapor is extremely hazardous under certain conditions. Care should be taken to avoid inhaling excess fumes. The flow of fuel through a fuel pump nozzle can produce static electricity, which can cause a fire if fuel is pumped into an ungrounded fuel container.
Page 186 Maintenance and care The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel system or cause the fuel cap to disengage in a collision, which may result in possible...
Page 187 Maintenance and care more pronounced. If the problems persist, see your dealer or a qualified service technician. It should not be necessary to add any aftermarket products to your fuel tank if you continue to use high quality fuel of the recommended octane rating.
Page 188 Maintenance and care Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not used. ESSENTIALS OF GOOD FUEL ECONOMY Measuring techniques Your best source of information about actual fuel economy is you, the driver.
Page 189 Maintenance and care • Use the same side of the same pump and have the vehicle facing the same direction each time you fill up. • Have the vehicle loading and distribution the same every time. Your results will be most accurate if your filling method is consistent. Calculating fuel economy 1.
Page 190 Maintenance and care • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. • Driving at reasonable speeds (traveling at 88 km/h [55 mph] uses 15% less fuel than traveling at 105 km/h [65 mph]). • Revving the engine before turning it off may reduce fuel economy. •...
Page 191 Maintenance and care • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain. • Transmissions give their best fuel economy when operated in the top cruise gear and with steady pressure on the gas pedal. •...
Page 192 Maintenance and care Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the engine compartment and exhaust system, which can start a fire. Illumination of the indicator, charging system warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power, could indicate that the emission control system is not working properly.
Page 193 Maintenance and care Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. BULBS Replacing exterior bulbs Check the operation of the following lamps frequently:...
Page 194 Maintenance and care Replacing headlamp bulbs To remove the headlamp bulb: 1. Make sure headlamp switch is in OFF position. 2. Remove the bolt from the headlamp housing. 3. At the back of the headlamp, pry up and remove the two retainer pins to release the headlamp assembly from the vehicle and pull headlamp forward.
Page 195 Maintenance and care 5. Disconnect the electrical connector from the bulb by pulling rearward. 6. Remove the bulb retaining ring by rotating it counterclockwise. 7. Remove the old bulb from the lamp assembly by pulling it straight out of the lamp assembly. To install the new bulb: Handle a halogen headlamp bulb carefully and keep out of children’s reach.
Page 196 Maintenance and care 2. Install the bulb retaining ring over the plastic base and lock the ring by rotating clockwise until it snaps into place. 3. Connect the electrical connector to the bulb. 4. Install the protective dust shield and lock the shield by rotating it clockwise until it locks into position.
Page 197 Maintenance and care 5. Carefully pull bulb straight out of the socket and push in the new bulb. 6. Install the bulb socket into the lamp assembly by rotating it clockwise. 7. Carefully position the headlamp assembly onto the vehicle. 8.
Page 198 Maintenance and care Note the number of the push pins before removal. 2. Remove the insulator by carefully prying out the push pins to gain access to the bulb sockets. 3. Remove the bulb socket by rotating it counterclockwise and pulling it down from the lamp assembly.
Page 199 Maintenance and care 5. Remove the rubber plug from the lower access hole in the upper portion of the liftgate. 6. Remove four nuts from the lamp assembly. 7. Carefully lift the lamp assembly away from the liftgate. 8. Remove the bulb socket by rotating it counterclockwise and pulling it out from the lamp assembly.
Page 200 Maintenance and care Replacing license plate lamp bulbs Wagon 1. Remove screw and the license plate lamp assembly from liftgate. 2. Remove bulb socket by turning counterclockwise. 3. Carefully pull the bulb out from the socket and push in the new bulb.
Page 201 Maintenance and care Replacing tail/brake/turn signal/backup lamp bulbs Sedan The tail lamp, brake lamp, turn signal lamp and backup lamp bulbs are located in the same portion of the tail lamp assembly. Follow the same steps to replace either bulb. 1.
Page 202 Maintenance and care Wagon The tail lamp/turn lamp bulbs are located in the same portion of the tail lamp assembly, one just below the other. Follow the same steps to replace either bulb: 1. Open the liftgate to expose the lamp assemblies.
Page 203 Maintenance and care Number of Function Trade Number bulbs 3457 AK Front park/turn lamp (amber) 9007 QL (9007 Headlamp LL optional) Tail lamp/brake/turn lamp 3157 Tail lamp/brake lamp (wagon) 3157 Rear turn lamp (wagon) 3156K Backup lamp Backup lamp (wagon) 3156K License plate lamp High-mount brake lamp...
Page 204 Maintenance and care Vertical aim adjustment 1. Park the vehicle on a level surface approximately 7.6 meters (25 feet) from a vertical wall or screen directly in front of it. • (A) Eight feet • (B) Center height of lamp to ground •...
Page 205: Customer Assistance
Maintenance and care To see a clearer light pattern for adjusting, you may want to block the light from one headlamp while adjusting the other. 5. Locate the vertical adjuster on each headlamp. Using a 4 mm wrench, turn the adjuster either clockwise (to adjust down) or counterclockwise (to adjust up).
Page 206 Maintenance and care Any gasoline spilled on the vehicle or deposits such as bird droppings should be washed and sponged off as soon as possible. Deposits not removed promptly can cause damage to the vehicle’s paintwork. Remove any exterior accessories, such as antennas, before entering a car wash.
Page 207 Maintenance and care Cleaning the wheels Wash with the same detergent as the body of your vehicle. Do not use acid-based or alcohol-based wheel cleaners, steel wool, fuel or strong detergents. Never use abrasives that will damage the finish of special wheel surfaces.
Page 208 Maintenance and care blades should be cleaned on a regular basis, and blades or rubber elements replaced when worn. Cleaning the engine In order to identify your vehicle’s engine, refer to Identifying components in the engine compartment in the Maintenance and Care chapter.
Page 209 Maintenance and care • 3.0L Duratec engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. Avoid cleaner or polish that increases the gloss of the upper portion of the instrument panel.
Page 210 Maintenance and care Do not use chemical solvents or strong detergents when cleaning the seat mounted side air bag. Such products could contaminate the side air bag system and affect performance of the side air bag in a collision. Woodtone trim Wipe stains with a soft cloth and a multi-purpose cleaning solution.
Page 211 Capacities and specifications MOTORCRAFT PART NUMBERS Component 3.0L V6 Vulcan engine 3.0L DOHC V6 Duratec engine Air filter element FA-1683 FA-1683 Fuel filter FG-1006 FG-81006 Battery (standard) BXT-58R BXT-36R Battery (optional) BXT-36R Oil filter FL-400-S FL-820-S PCV valve EV-228 EV-243 Spark plugs AWSF-32PP AWSF-32F...
Page 212 Capacities and specifications REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid High Fill to line on Performance reservoir DOT 3 Motor Vehicle Brake Fluid Engine Premium 3.0L V6 Vulcan 11.0L coolant Engine Coolant engine (11.6 quarts) 3.0L DOHC V6 10.0L Duratec engine (10.6 quarts)
Page 213 Capacities and specifications Fluid Ford Part Application Capacity Name Windshield Ultra-Clear Wagon 1.8L (60.9 oz.) washer fluid - Windshield Rear Washer Concentrate Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter.
Page 214 Capacities and specifications Ford Part Ford Part Ford Items Name or Number Specification equivalent Engine coolant Ford Premium VC-4–A (in ESE-M97B44-A Engine Coolant Canada, (green colored) Motorcraft CXC-10) Power steering Motorcraft XT-2-QDX MERCON fluid MERCON ATF Windshield Ultra-clear C9AZ-19550-AC ESR-M17P5-A washer fluid Windshield Washer...
Page 215 Capacities and specifications...
Page 216: Certification Label
Capacities and specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety MFD. BY FORD MOTOR CO. IN U.S.A. Administration Regulations require DATE: XXXXX GVWR:XXXXX LB/ XXXXX KG that a Certification Label be affixed FGAWR: XXXXXX/XXXXXXX RGAWR: XXXXXXX/XXXXXXX THIS VEHICLE CONFORMS TO ALL APPLICABLE FEDERAL to a vehicle and prescribe where the MOTOR VEHICLE SAFETY STANDARDS IN EFFECT ON THE Certification Label may be located.
Page 217 Capacities and specifications Vehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side XXXXXXXXXXXXXXXXX instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number.) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on the engine block, frame and transaxle.
Page 218: Customer Assistance
Warranty expires You may purchase Ford ESP from any participating Ford and Lincoln Mercury and Ford of Canada dealer. There are several plans available in various time, distance and deductible combinations which can be tailored to fit your own driving needs. Ford ESP also offers reimbursement benefits for towing and rental coverage.
Page 219 Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 220 P.O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) In order to help you service your Ford or Lincoln Mercury vehicle, please have the following information available when contacting a Customer Relationship Center: • Your telephone number (home and business) •...
Page 221 Unresolved warranty repair concerns or vehicle performance as designed concerns on Ford and Lincoln Mercury cars and Ford and Lincoln Mercury light trucks which are within the terms of any applicable written new vehicle warranty are eligible for review, except those involving: •...
Page 222 • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and trained by an independent consulting firm. The dealership Board member is chosen from Ford and Lincoln Mercury dealership management, recognized for their business leadership qualities. What the Board needs...
Page 223 Customer assistance • the date of repair(s) and mileage at the time of occurrence(s) • the current mileage • the name of the dealer(s) who sold or serviced the vehicle • a brief description of your unresolved concern • a brief summary of the action taken by the dealer(s) and Ford Motor Company •...
Page 224 Customer assistance To Request a DSB Brochure/Application For a brochure/application, speak to your dealer or write/call to the Board at the following address/phone number: Dispute Settlement Board P.O. Box 5120 Southfield, MI 48086–5120 1–800–428–3718 You may also contact the North American Customer Relationship Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company...
Page 225 Customer assistance GETTING ASSISTANCE OUTSIDE THE U.S. AND CANADA Before exporting your vehicle to a foreign country, contact the appropriate foreign embassy or consulate. These officials can inform you of local vehicle registration regulations and where to find unleaded fuel. If you cannot find unleaded fuel or can only get fuel with an anti-knock index lower than is recommended for your vehicle, contact a district or owner relations/customer relationship office.
Page 226 Customer assistance FORD CAR CARE PRODUCTS FOR YOUR VEHICLE Ford has many quality products available from your dealer to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 227 FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Ford accessories are available for your vehicle through your local authorized Ford, Lincoln Mercury or Ford of Canada dealer. These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your vehicle.
Page 228 Customer assistance Travel equipment Electrochromic inside mirror with compass Electrochromic inside mirror with compass and temperature Emergency kit Factory luggage rack adaptors First aid kit Framed luggage carrier HomeLink Removable luggage rack Removable luggage rack adapters Soft luggage cover Speed control Track rider bars Protection and appearance equipment Air bag anti-theft locks...
Page 229 Customer assistance For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight capacity of the vehicle or of the front or rear axle (GVWR or GAWR as indicated on the Safety compliance certification label).
Page 230 Customer assistance Obtaining a French owner’s guide French Owner’s Guides can be obtained from your dealer or by writing to Ford Motor Company of Canada, Limited, Service Publications, P.O. Box 1580, Station B, Mississauga, Ontario L4Y 4G3. IN CALIFORNIA (U.S. ONLY) California Civil Code Section 1793.2(d) requires that, if a manufacturer or its representative is unable to repair a motor vehicle to conform to the vehicle’s applicable express warranty after a reasonable number of...
Page 231: Reporting Safety Defects
Reporting safety defects REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company.
Page 232: Index
Index Accessory delay ......57 Battery ........175 acid, treating emergencies ..175 Air bag supplemental charging system restraint system ....96–97, 101 warning light ......13 and child safety seats ....99 jumping a disabled battery ..147 description ......97, 101 maintenance-free ....175 disposal ........103 replacement, specifications ...210 driver air bag ....97, 100, 102 servicing ........175 indicator light .....13, 99...
Page 233 Index Child safety seats ......105 Getting assistance outside attaching with tether straps ..109 the U.S. and Canada ....224 in front seat ......106 Getting roadside assistance ...135 in rear seat ......106, 109 Getting the LATCH ........111 service you need ....217 Ordering additional Cleaning your vehicle ....204 owner’s literature ....228 engine compartment ....207...
Page 234 Index idle speed control ....175 safety information relating to lubrication automotive fuels .....182 specifications ....212–213 Fuses ........138–139 refill capacities ......211 service points ....155–156 starting after a collision ..136 Engine block heater ....116 Gas cap (see Fuel cap) ..9, 184 Engine oil ........157 Gas mileage checking and adding ....157 (see Fuel economy) ....187...
Page 235 Index high beam ......8, 17 positions of the ignition ...47 replacing bulbs .......193 turning on and off ....17 warning chime ......13 Lamps Heating ........19 autolamp system .......18 heating and bulb replacement air conditioning system ....19 specifications chart ....201 Hood ..........154 cargo lamps .......18 daytime running light ....17 fog lamps ........18...
Page 236 Index GAWR ........128 Power door locks ......57 GVWR ........128 Power steering ......122 trailer towing ......128 fluid, checking and adding ..167 Locks fluid, refill capacity ....211 autolock ........71 fluid, specifications ..212–213 childproof ........57 Lubricant specifications ...212–213 Lumbar support, seats ....79 Radio ..........29 Relays ........138, 143 Remote entry system ...63, 65 Mirrors .........54...
Page 237 Index child safety seats ....105 lubricant specifications ..213 cleaning ......208–209 Transmission SecuriLock passive fluid, checking and adding anti-theft system ....73, 75 (automatic) ......168 lubricant specifications ..212 Servicing your vehicle ....153 Trip odometer ......15 Spark plugs, specifications .....210, 213 Trunk ......61, 63–64, 76 remote release ......60 Specification chart, lubricants ......212–213...
Page 240: Filling Station Information
Filling station information Item Information Required fuel Refer to Octane recommendations in the Maintenance and care chapter. Fuel tank capacity 68.1L (18 gallons) Engine oil capacity (including filter 4.25L (4.5 quarts) Use Motorcraft change)-3.0L V6 Vulcan engine SAE 5W-20 Super Premium Motor Oil, Ford specification WSS-M2C153-H.
Page 241 Filling station information Use Ford Premium Engine Coolant (green in color). DO NOT USE Ford Extended Life Engine Coolant (orange in color). Refer to Adding engine coolant, in the Maintenance and Care chapter. Ensure the correct automatic transmission fluid is used. Transmission fluid requirements are indicated on the dipstick or on the dipstick handle.

Mercury Sable 2001 Owner's Manual

Quick Links

Related Manuals for Mercury Sable 2001

Summary of Contents for Mercury Sable 2001

Table of Contents