Page 1 www.carburetor-manual.com Would you like some Free Manuals? http://carburetor-manual.com/free-shop-manual-club-t-13.html Also visit http://freeshopmanual.com for more Free Manuals Also Visit my website for 7 FREE Download Manuals starting with this one. "The ABC's of Carburetion" Click Here Now file:///C|/Documents%20and%20Settings/Tim/Desktop/carburetor-manual-welcome/index.htm[4/25/2009 11:42:20 AM]...
Page 2 Table of Contents Table of Contents Introduction Instrument Cluster Warning and control lights Gauges Entertainment Systems AM/FM stereo cassette with CD AM/FM stereo with CD Rear seat controls Rear seat entertainment system Navigation system Climate Controls Manual heating and air conditioning Electronic automatic temperature control Lights Headlamps...
Page 3: Table Of Contents
Table of Contents Locks and Security Keys Locks Anti-theft system Seating and Safety Restraints Seating Safety restraints Air bags Child restraints Driving Starting Brakes Air suspension Transmission operation Vehicle loading Trailer towing Roadside Emergencies Getting roadside assistance Hazard flasher switch Fuel pump shut-off switch Fuses and relays Changing tires...
Page 5: Introduction
State of California to cause cancer and birth defects or other reproductive harm. CONGRATULATIONS Congratulations on acquiring your new Ford. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.
Page 6 Introduction SAFETY AND ENVIRONMENT PROTECTION Warning symbols in this guide How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol.
Page 7 This information may be stored during regular operation or in a crash or near crash event. This stored information may be read out and used by: • Ford Motor Company. • service and repair facilities. • law enforcement or government agencies.
Page 8 Introduction Special instructions For your added safety, your vehicle is fitted with sophisticated electronic controls. Please read the section Supplemental Restraint System (SRS) in the Seating and safety restraints chapter. Failure to follow the specific warnings and instructions could result in personal injury. Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the air bag can be and is turned OFF.
Page 9 Introduction These are some of the symbols you may see on your vehicle. Vehicle Symbol Glossary Safety Alert See Owner’s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation Child Seat Lower Warning Anchor Child Seat Tether Brake System Anchor Brake Fluid -...
Page 10 Introduction Vehicle Symbol Glossary Power Windows Power Window Lockout Front/Rear Interior Luggage Child Safety Door Compartment Release Lock/Unlock Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant Temperature Do Not Open When Hot Battery Avoid Smoking, Flames, Battery Acid or Sparks Explosive Gas Fan Warning Maintain Correct Fluid...
Page 11: Instrument Cluster
Instrument Cluster Instrument Cluster WARNING LIGHTS AND CHIMES Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works.
Page 12 Instrument Cluster Light is blinking: Engine misfire is occurring which could damage your catalytic converter. You should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity. Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior floor coverings or other vehicle components, possibly causing a fire.
Page 13 Instrument Cluster Safety belt Illuminates to remind you to fasten your safety belts. For more information, refer to the Seating and safety restraints chapter. Air bag readiness Illuminates to confirm that the air bags (front or side) are operational. If the light fails to illuminate, continues to flash or remains on, have the system serviced immediately.
Page 14 Instrument Cluster Speed control Illuminates when the speed control is activated. Oil pressure/Engine coolant Illuminates when the engine coolant temperature is above the normal range or the engine oil pressure is outside normal range. Check the engine oil and coolant level refer to Adding engine oil and Adding coolant in the Maintenance and specifications chapter.
Page 15 Instrument Cluster Four wheel drive low (if equipped) Illuminates when four-wheel drive low is engaged. If the light continues to flash have the system serviced. Four wheel drive high (if equipped) Illuminates when four-wheel drive is put in high range. If the light HIGH continues to flash have the system serviced.
Page 16: Gauges
Instrument Cluster GAUGES Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within the normal area (the area between the “H” and “C”). If it enters the red section, the engine is overheating.
Page 17 Instrument Cluster Engine oil pressure gauge Indicates engine oil pressure. At normal operating temperature, the needle will be in the normal range (the area between the “L” and “H”); if the needle goes below the normal range, stop the vehicle as soon as safely possible and switch off the engine immediately.
Page 18 Instrument Cluster If the key is left in the ON position during fueling, a minimum of 22.2 L (six gallons) must be added to the fuel tank in order for the gauge to instantaneously update. If less than six gallons is added, the gauge will take between five to twenty minutes to update.
Page 19 Instrument Cluster • Optional instrument cluster Press and release the TRIP/RESET button to toggle between the odometer and trip odometer display. Press and hold the button to reset. Tachometer Indicates the engine speed in revolutions per minute. Driving with your tachometer pointer continuously at the top of the scale may damage the engine.
Page 20: Entertainment Systems
Entertainment Systems Entertainment Systems PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD 1. EJ (Eject): Press to stop and eject a tape. 2. EJ (Eject): Press to stop and eject a CD. 3. BASS: Allows you to increase or decrease the audio system’s bass output.
Page 21 Entertainment Systems 4. BAL (Balance): Allows you to shift speaker sound between the right and left speakers. Press BAL then press SEL to shift sound to the left or right FADE: Allows you to shift speaker sound between the front and rear speakers.
Page 22 Entertainment Systems 9. REW (Rewind): Works in tape and CD modes. In tape mode, radio play continues until rewind is stopped (with the TAPE control) or the beginning of the tape is reached. In CD mode, REW control reverses the CD within the current track. FF (Fast Forward): Works in tape and CD modes.
Page 23 Entertainment Systems The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired. •...
Page 24 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 25 Entertainment Systems PREMIUM IN-DASH SIX CD SOUND SYSTEM AUDIOPHILE IN-DASH SIX CD SOUND SYSTEM 1. SEEK: Works in radio or CD mode. Press and release SEEK for previous/next strong station or track.
Page 26 Entertainment Systems 2. REW (Rewind): In CD mode, press to reverse within the current track. FF (Fast forward): In CD mode, press to advance within the current track 3. COMP or DSP COMP (Compression): The compression feature operates in CD mode and brings soft and loud CD passages together for a more consistent listening level.
Page 27 Entertainment Systems 5. EJ (Eject): To eject a single disc, press EJ and the corresponding preset button number. Press and hold to eject all loaded discs. The eject feature is active whether the ignition is on or off. 6. BASS: Press BASS; then press to decrease/increase the bass output.
Page 28 Entertainment Systems • FIND Program type: Allows you to search RDS-equipped stations for a certain category of music format: Classic, Country, Info, Jazz, Oldies, R&B, Religious, Rock, Soft, Top 40. Press RDS until FIND appears in the display then use the SEL control to scroll through the desired music types.
Page 29 Entertainment Systems 13. PUSH ON (Power/volume): Press to turn ON/OFF; turn to increase or decrease volume levels. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal”...
Page 30 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 31: Rear Seat Controls
Entertainment Systems When the rear seat controls are activated, rear seat passengers can use the controls to change the playing media for all passengers (Single Play mode). In this mode, all speakers will play audio from the same media source for all passengers to hear. To activate the rear seat radio controls: •...
Page 32 Entertainment Systems To adjust the volume The volume control allows the rear seat passengers to adjust the volume level of the audio system. Press the + control to increase - VOLUME + volume. MODE Press the - control to decrease volume.
Page 33 Entertainment Systems Mode select Push the MODE control to toggle - VOLUME + between AM, FM1, FM2, tape (if MODE equipped), CD, CD changer (if equipped) or DVD (if equipped). If in Dual Play mode, SHARED SEEK MEMORY illuminates in the radio display when the front and rear modes are set to the same media.
Page 34 Entertainment Systems Parental control Press the memory preset controls 3 and 5 simultaneously on the front audio controls to disable the rear seat controls. They will remain disabled until the front seat passengers “enable” them again by simultaneously pressing the 3 and 5 preset controls.
Page 35 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 36 Entertainment Systems DVD player controls 1. MAIN control • NEXT — Press to access the next track on the CD, the next chapter on the DVD, or to go up in cursor mode. • PREV — Press to access the previous track on the CD, the previous chapter on the DVD, or to go down in cursor mode.
Page 37 Entertainment Systems 7. Auxiliary jacks Insert lines for standard video game players. 8. STOP/EJECT control Press once to stop DVD play. Press again to eject the DVD. 9. DISPLAY (DISP) control Press to enable on screen display of player menu and user display adjustments.
Page 38 Entertainment Systems • Press the FWD control to move the cursor right one position NEXT PREV Next/Previous control The NEXT (up) and PREV (down) controls allow you to access the NEXT next or previous track on a CD or PREV chapter on a DVD.
Page 39 Entertainment Systems Slow play mode To enter slow play mode, press the PLAY/PAUSE control. Once the system is in pause mode, press the FWD or REV control for slow motion playback. Three different speeds are available depending on how long the control is held. Press the control once for slow motion playback.
Page 40 Entertainment Systems Remote control SEEK DISP MODE MEMORY 1. REWIND control Press to reverse the direction of the DVD movie. 2. FAST FORWARD control Press to advance the direction of the DVD movie. 3. PLAY/STOP control Press to play or stop the DVD movie. 4.
Page 41 Entertainment Systems In stop mode, press to change to a different playing media (e.g. AM, FM, CD . . . ) 8. VOLUME control Press to increase (+) or decrease (-) volume level. Battery replacement Batteries are supplied with the remote control unit.
Page 42 Entertainment Systems To install the batteries, lightly press down on the top of the left earpiece and slide the cover off. When replacing the batteries, use two new batteries (alkaline recommended) and install them with the correct (+) and (-) orientation.
Page 43 Entertainment Systems Liquid Crystal Display (LCD) flip-down screen The screen rotates down to view and into the housing to store when not in use. Be sure the screen is latched into the housing when being stored. 1. 7.0” (diagonal) active matrix liquid crystal display (LCD) screen. 2.
Page 44 DVDs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford DVD/CD players. Irregular shaped discs, discs with a scratch protection film attached, and discs with homemade paper (adhesive) labels should not be inserted into the player.
Page 45 Entertainment Systems Inserting a CD/DVD Inserting a CD/DVD into the DVD player automatically turns the power ON and playback should begin. The counter is automatically reset to 0:00:00. Removing a CD/DVD 1. Press the STOP/EJECT control to stop playback. 2. Press the STOP/EJECT control again to eject the CD/DVD. If the CD/DVD is not removed within the allotted time, the system will pull the CD/DVD back into the system for safety purposes.
Page 46 Do not attempt to service, repair or modify the Rear Seat Entertainment DVD System. See your Ford or Lincoln Mercury dealer. Do not insert foreign objects into the DVD compartment. The front glass on the liquid crystal display (LCD) flip-down screen may break when hit with a hard surface.
Page 47 Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford Motor Company could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 48 Entertainment Systems Care and service of the DVD player Environmental extremes DVD players that are subjected to harsh environmental conditions may be damaged or perform at less than maximum capability. To avoid these outcomes, whenever possible avoid exposing your DVD player to: •...
Page 49: Navigation System
Motor Company shall not be liable for any damages of any type arising from failure to follow these guidelines. Do not attempt to service, repair or modify the system. See your Ford or Lincoln Mercury dealer. The driver must not attempt to operate any detailed operation of the navigation system while the vehicle is in motion.
Page 50 • Set the volume level so that you can hear directions clearly. • Do not disassemble or modify the system as this may lead to damage and void your warranty. If a problem occurs, stop using the system immediately and contact your Ford or Lincoln Mercury Dealer.
Page 51 Entertainment Systems System overview 13 14 H E R E H O M E N A V M E N U PUSH B A C K A M / F M M A P S E E K 1. HOME: When the home location is empty, pressing and holding this H O M E key will store the vehicle’s current...
Page 52 Entertainment Systems 4. Cursor control: Use this control when viewing a menu in the navigation system. Press the control up or down, left or right to highlight an item in the display. Press the center of the control to make your selection.
Page 53 Entertainment Systems 11. On/volume: Press the ON PUSH control to turn on the VNR system. Press again to turn the system off. Turn the control to adjust the audio volume levels. To adjust the voice PUSH output levels from the navigation system, adjust the volume levels only during voice output.
Page 54 Entertainment Systems 2. Press the AM/FM control to select the desired frequency band. A M / F M 3. Press the SEEK control to locate S E E K a station. To play a CD in the VNR: 1. Ensure that the ignition and the VNR system are ON.
Page 55 Entertainment Systems 2. Press the NAV control to enter into Navigation mode. N A V 3. To enter a destination, ensure that the vehicle is in the PARK position. 4. To navigate to home from the current location, press HOME. If a H O M E home location has not previously been stored, pressing and holding...
Page 56 Entertainment Systems Turn the control to raise or lower volume. The levels will be displayed PUSH on the screen. To adjust the navigation voice output level, adjust the volume control only when the navigation system is speaking. Otherwise, it will adjust the radio levels. Automatic volume control (AVC) With this feature, radio volume changes automatically with vehicle speed to compensate for road and wind noise.
Page 57: Rear Seat Entertainment System
Entertainment Systems AM/FM select The AM/FM control works in radio, CD and navigation modes. A M / F M AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to switch between AM, FM1 or FM2 memory preset stations. AM/FM select in CD mode Press to stop CD play and begin radio play.
Page 58 Entertainment Systems If a navigation CD is in the head unit and you press CD, the system will automatically search for an audio CD in the CD DJ and begin play if it is present. Adjusting the levels 1. Press the MENU control. M E N U 2.
Page 59 Entertainment Systems Press the soft key to turn the feature on or off. This feature can be accessed by selecting the menu option “More, AVC, Traffic, DSP..” within the “Audio Options” menu. You can then select the following signal modes: •...
Page 60 Entertainment Systems Seek in CD or CD DJ mode • Press to seek to the previous track of the current disc. If a selection has been playing for three seconds or more and you press , the CD changer will replay that selection from the beginning.
Page 61 Entertainment Systems Starting autoset memory preset 1. Select a frequency band using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing.
Page 62 Entertainment Systems Scan function Press the soft key next to SCAN for a brief sampling of all listenable stations on the selected frequency. Press again to disable scan and remain on the current station. Program type (PTY) selections Some FM stations transmit program type codes which can be used to locate different stations transmitting programs of a certain type.
Page 63 Entertainment Systems Compression The compression feature will boost quieter music and lower louder music to minimize the need for volume adjustments. When in CD or CD DJ mode, press COMP to engage or disengage the compression feature. Shuffle When in CD or CD DJ mode, press SHUF to engage and disengage the shuffle feature.
Page 64 Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player.
Page 65 Entertainment Systems Press to eject the magazine. 1. Pull the lever to remove a CD tray from the magazine. 2. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing If you pull too hard on the disc holder, the disc holder may come completely out of the magazine.
Page 66 Entertainment Systems 4. Insert the CD magazine into the CD DJ. 5. Slide the door to the left to close. Use only compact discs containing this mark. The magazine does not need to be full for the CD DJ to operate. Radio power must be turned on to play the CDs in the CD DJ.
Page 67 Entertainment Systems CD DJ information screen The CD DJ screen will display various information such as: • Track selected • Elapsed time • Selected disc • Volume level • On-screen selections CD DJ playback With a navigation CD inserted into the audio unit, press CD for CD DJ playback.
Page 68 Entertainment Systems Scan feature When in CD DJ mode, press SCAN for a brief sampling of all tracks on the current CD. Press again to disengage the feature and listen to the selected song. Shuffle mode When in CD DJ mode, press SHUF to engage and disengage the shuffle feature.
Page 69 Entertainment Systems When RSC is active, pressing presets 2 and 4 simultaneously on the radio will enable Dual Play mode (or the RSC can enable Dual Play mode by pressing the button). The front speakers play the selected media and the rear speakers mute. In this mode, the rear passengers may adjust the volume and other levels using the rear seat control.
Page 70 Entertainment Systems 6. ZOOM 7. PAN 8. DETOUR 9. VOICE Please drive safely This screen may appear on your VNR display. Press the soft key next to the display to select the desired language. Press the control next to ACCEPT to confirm your selection. Principles of GPS (Global Positioning System) operation Your Vehicle Navigation System directs you based on information derived from satellites, road maps stored on the CD, sensors in your vehicle and...
Page 71 Entertainment Systems The GPS signal strength may vary. The directional heading indicator at the bottom of the screen might change color to indicate this signal strength. The colors are as follows: • Green — A clear GPS signal is being received. •...
Page 72 Entertainment Systems Selecting a destination Press NAV to access the destination entry menu. N A V From this menu, you may select from the following options: • Address/Intersection – Use to select a destination based on a known street address or intersection.
Page 73 Entertainment Systems Points of Interest (POI) This destination option enables you to specify a particular place, such as an airport or gas station. Use the soft keys to select Points of Interest. In the next menu, you will have the following options: •...
Page 74 Entertainment Systems Previous destination The last 50 destinations entered into the navigation system are automatically stored in the system’s memory. Use the soft key to select Previous Destination. The address of each stored destination will appear. The previous origin information is also stored in this location.
Page 75 Entertainment Systems • Use the cursor control to scroll through the selections. • Press in the cursor control to confirm the selection. Selecting Route Criteria Once you have selected a destination, select from the following route criteria: 1. Shortest time route — Creates a driving route which minimizes driving time taking into consideration things such as speed limits, number of turns, etc.
Page 76 Entertainment Systems Please proceed Once the route is calculated, ’Please Proceed’ is displayed with a map on the display. Also included in the display: • the planned route is shown in pink • major roadways are shown in blue • other streets are shown in white •...
Page 77 Entertainment Systems • CANCEL — Press to cancel the guide display. While in the Guide display screen, the cursor input can be used to preview future/up coming maneuvers. This can be done by pressing down on the cursor input to go to the ’next’ maneuver instruction, and pressing up to go to the ’previous’...
Page 78 Entertainment Systems Adding, deleting or editing the address book Note: These features are not available when the vehicle is in motion. 1. Ensure that you are in navigation mode. 2. Select Address book. 3. Confirm selection. 4. Press the DELETE soft key to delete the current entry.
Page 79 Entertainment Systems Current location To access your current location, press HERE when in navigation H E R E mode. Your current location and the name/distance to the next/last intersection are displayed. Press NAV to return to a guidance display. Press MAP to return to a map display.
Page 80 Entertainment Systems Route interruptions In the course of your destination, you may decide to temporarily leave your planned route for gas, food, etc. If you turn off the ignition, the option to continue the route guidance will be displayed when the ignition is turned on again.
Page 81 Entertainment Systems Navigation options Once in the navigation preference menu, you may select from the following options: • VOICE — Select to turn the voice output on or off and to adjust the volume level. • MAP — Choose between ’Heading up’...
Page 82 General information Federal Communication Commission (FCC) Compliance Changes or modifications not approved by Ford or Lincoln Mercury could void user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 83 Entertainment Systems Cleaning the display Do not spray cleaning fluid directly onto the unit. Instead, spray onto a soft cloth and gently wipe the unit. Only recommended products should be used. Do not clean any part of the system with benzene, paint thinner or any other solvent.
Page 84: Climate Controls
Climate Controls Climate Controls MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. Temperature control 4. Rear defrost control 2. Mode selector control 5. Fan speed control 3. A/C control FAN SPEED CONTROL Controls the volume of air circulated in the vehicle. TEMPERATURE CONTROL KNOB Controls the temperature of the airflow inside the vehicle.
Page 85 Climate Controls MODE SELECTOR CONTROL Controls the direction of the airflow to the inside of the vehicle. The A/C compressor will only function if the outside temperature is above approximately 2°C (35°F) • MAX A/C – Distributes recirculated air through the instrument panel registers.
Page 86 Climate Controls A/C control Used to manually enable or disable the operation of the air conditioning in all modes except Floor & Defrost, Defrost and Max A/C. When manual A/C is selected (On) the indicator will be lit. When manual A/C is selected (Off) the indicator will not be lit.
Page 87: Electronic Automatic Temperature Control
Climate Controls DUAL ELECTRONIC AUTOMATIC TEMPERATURE CONTROL (DEATC) SYSTEM (IF EQUIPPED) 1. A/C control 9. Panel & Floor control 2. Recirculated air control 10. Panel control 3. Passenger temperature control 11. OFF control 4. Rear defrost control 12. AUTO control 5.
Page 88 Climate Controls AUTOMATIC OPERATION Press AUTO and select the desired temperature. The system will either heat or cool the vehicle to achieve the selected temperature. The system will automatically determine fan speed, airflow location and whether outside or recirculated air AUTO is required.
Page 89 Climate Controls TEMPERATURE CONVERSION Press the F/C control to switch between Fahrenheit and Celsius temperature on the display. The temperature in Celsius will be displayed in half-degree increments. The English/Metric control on the trip computer and message center AUTO (if equipped) will not change the temperature display.
Page 90 Climate Controls In automatic operation, the air conditioning operates as necessary to achieve the selected temperature and the A/C indicator will be lit. If desired, the air conditioning can be controlled manually through the use of the A/C control. When the air conditioning is controlled while in automatic operation, the AUTO indicator will remain lit and the system will remain in automatic operation.
Page 91 Climate Controls MANUAL OVERRIDE CONTROLS DUAL AUTO The manual override controls allow you to determine where airflow is directed. To return to full automatic control, press AUTO. The A/C compressor will only function if the outside temperature is above approximately 2°C (35°F). •...
Page 92 Climate Controls OPERATING TIPS • To reduce fogging in humid weather conditions, unless in Defrost or Floor & Defrost, press the A/C control before driving as the air conditioning removes moisture form the air. • To reduce humidity buildup inside the vehicle in warm weather conditions, do not drive with the climate control system in the Off mode.
Page 93 Climate Controls The auxiliary climate control system is dependent on the main climate control system. If the main climate control system is in the Off position, the auxiliary climate control will not operate. If the main climate control system is on, the auxiliary air will not be cooled unless the air conditioning is functioning on the main climate control system.
Page 94 Climate Controls REAR WINDOW DEFROSTER Used to manually enable or disable rear window defrost in all modes. After approximately 10 minutes of rear defrost operation, the climate control system will automatically disable the rear defrost operation. If desired, the rear defrost can be manually disabled through the use of the rear defrost button.
Page 95: Lights
Lights Lights HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Foglamp control (if equipped) The headlamp control also operates the foglamps. The foglamps can be turned on when the headlamp control is in the positions and the high beams are...
Page 96 Lights Daytime running lamps (DRL) (if equipped) Turns the foglamps on at full intensity output. To activate: • the ignition must be in the ON position and • the headlamp control must be in the OFF or Parking lamps position. Always remember to turn on your headlamps at dusk or during inclement weather.
Page 97 Lights PANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the full down position, past detent, to prevent the interior lights from illuminating when the doors are opened.
Page 98: Turn Signal Control
Lights 5. Locate the vertical adjuster on each headlamp, then use a 10 mm socket/wrench to turn the adjuster either counterclockwise (to adjust down) or clockwise (to adjust up) aligning the upper edge of the light pattern up to the horizontal line. 6.
Page 99 Lights Front row dome lamp/ map light (if equipped) The dome lamp lights when: • any door is opened, • the instrument panel dimmer switch is rotated up until the courtesy lamps come on, and • any of the remote entry controls are pressed and the ignition is OFF.
Page 100 To replace all instrument panel lights - see your dealer * To obtain replacement approach lamp assembly bulbs, see your dealer and reference Ford part no. 2L1Z–13B374–BB for the passenger side mirror and 2L1Z–13B375–BB for the driver side mirror. Replacing the interior bulbs...
Page 101 Lights Map lamps To change the map lamp bulbs: 1. Use a small screwdriver to remove the map lamp lens. 2. To remove the old bulb, twist ⁄ turn and pull it out. 3. Twist in a new bulb. 4. Align and press the map lamp lens back on and test the lamp operation.
Page 102 Lights 7. Once the bulb covers are removed, the bulbs can be removed by turning them counterclockwise and then pulling the bulbs straight out. Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass.
Page 103 Lights 5. Rotate the bulb socket counterclockwise and remove from the lamp assembly. 6. Carefully pull the bulb out of the socket and push in the new bulb. 7. Install the bulb socket into the lamp assembly and rotate clockwise. 8.
Page 104 Lights Replacing foglamp bulbs Handle a halogen headlamp bulb carefully and keep out of children’s reach. Grasp the bulb only by its plastic base and do not touch the glass. The oil from your hand could cause the bulb to break the next time the headlamps are operated.
Page 105 Lights Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. To change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly.
Page 106 Lights Approach lamp bulb removal (if equipped) To change the bulbs: 1. Make sure that all the doors are closed and the interior lights have automatically turned off or the opposite mirror approach lamp has turned off. 2. With a small flat tipped screwdriver, insert the tip into the approach light module slot located on the outboard corner of the lens...
Page 107: Driver Controls
Driver Controls Driver Controls WINDSHIELD WIPER/WASHER CONTROLS Rotate the windshield wiper control to the desired interval, low or high speed position. INT1 The bars of varying length are for intermittent wipers. When in this position rotate the control upward for fast intervals and downward for slow intervals.
Page 108 Driver Controls Checking the wiper blades If the wiper blades do not wipe properly, clean both the windshield and wiper blades using undiluted windshield wiper solution or a mild detergent. Rinse thoroughly with clean water. To avoid damaging the blades, do not use fuel, kerosene, paint thinner or other solvents. Changing the wiper blades It is recommended that wiper blades are renewed before winter.
Page 109 Driver Controls TILT STEERING Push the lever down to unlock the steering column. While the lever is in the down position, tilt the steering column to the desired position. While holding the steering wheel, pull the lever up to its original position to lock the steering column.
Page 110 Driver Controls OVERHEAD CONSOLE The appearance of your vehicle’s overhead console will vary according to your option package. Forward storage bin and conversation mirror (if equipped) The storage compartment may be used to store two pairs of sunglasses or similar objects. Press the release control to open the storage compartment.
Page 111 Driver Controls To vent: • To tilt the moon roof into the vent position (when the glass panel is closed), press and hold the top portion of the control. To close the moon roof from the vent position, press and hold the bottom portion of the control until the glass panel stops moving.
Page 112 Driver Controls AUXILIARY POWER POINT Power points are designed for accessory plugs only. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power point can cause damage not covered by your warranty. On vehicles equipped with a center console there are three power points located in the console.
Page 113: Power Windows
Driver Controls Not equipped with rear climate control POWER WINDOWS Press and hold the rocker switches to open and close windows. • Press the top portion of the rocker switch to close. • Press the bottom portion of the rocker switch to open.
Page 114: Mirrors
Driver Controls One touch down • Press the bottom portion of the rocker switch completely down and release quickly. The driver’s window will open fully. Depress again to stop window operation. One touch down can be deactivated during operation by pushing down on the top part of the driver power window control.
Page 115 Driver Controls Press the control to turn the mirror OFF or AUTO. The mirror will automatically return to the normal state whenever the AUTO vehicle is placed in R (Reverse)(when the mirror is on) to ensure a bright clear view when backing up.
Page 116 Driver Controls Reverse tilt down mirrors (if equipped) The side mirrors may be programmed to tilt down when the vehicle is put in R (Reverse). Refer to the Message Center in the Driver Controls chapter to turn this feature ON or OFF. Signal mirrors (if equipped) When the turn signal is activated, the lower portion of the mirror...
Page 117: Speed Control
Driver Controls POWER ADJUSTABLE FOOT PEDALS The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. •...
Page 118 Driver Controls To turn speed control off • Press OFF or • Turn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. To set a speed • Press SET+. For speed control to operate, the speed control must be ON and the vehicle speed must be greater than 48 km/h (30...
Page 119 Driver Controls To set a higher set speed • Press and hold SET +. Release the control when the desired vehicle speed is reached or • Press and release SET + to operate the Tap-Up function. Each press will increase the set speed by 1.6 km/h (1 mph) or COAST •...
Page 120 Driver Controls To disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. To return to a previously set speed • Press RES. For RES to operate, the vehicle speed must be faster than 48 km/h (30 mph).
Page 121 Driver Controls Indicator light This light comes on when either the SET ACCEL or RES controls are pressed. The vehicle speed must be at or above 48 km/h (30 mph). It turns off when the speed control OFF control is pressed, the brake or clutch is applied, or the ignition is turned to the OFF position.
Page 122 Driver Controls In any mode: • Press VOL + or − to adjust volume. Climate control features Press TMP + or - to adjust temperature. Press + or - to adjust fan speed. HOMELINK WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device.
Page 123 Driver Controls When programming your HomeLink Wireless Control System to a garage door or gate, be sure that people and objects are out of the way to prevent potential harm or damage. Do not use the HomeLink Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S.
Page 124 Driver Controls 3. Simultaneously press and hold both the HomeLink and hand-held transmitter button. Do not release the buttons until step 4 has been completed. Some entry gates and garage door openers may require you to replace step 3 with procedures noted in the “Gate Operator and Canadian Programming”...
Page 125 Driver Controls Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink to accept the signal from the hand-held transmitter. After completing steps 1 and 2 outlined in the “Programming” section, replace step 3 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling”...
Page 126 Driver Controls Erasing HomeLink buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink buttons until the red indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.
Page 127 Driver Controls Compass The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antennas. Magnetic or metallic objects placed in, on or near the vehicle may also affect compass accuracy. Usually, when something affects the compass readings, the compass will correct itself after a few days of operating your vehicle in normal conditions.
Page 128: Message Center
Driver Controls Compass calibration adjustment Perform this adjustment in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1.
Page 129 Driver Controls Info menu This control displays the following control displays: • Odometer/Compass • Trip odometer/Odometer/Compass • Distance to Empty • Average Fuel Economy • Trip Elapsed Drive Time Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Compass display The compass reading may be affected when you drive near large buildings, bridges, power lines and powerful broadcast antenna.
Page 130 Driver Controls Compass zone/calibration adjustment 1. Determine your magnetic zone by referring to the zone map. 2. Turn ignition to the ON position. 3. Start the engine. 4. From Info menu, select the Compass/Odometer function. (Do not select Trip, DTE, or AFE. The top of the message center must be blank).
Page 131 Driver Controls 10. The compass is now calibrated. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in liters/100 km or miles/gallon. If you calculate your average fuel economy by dividing liters of fuel used by 100 kilometers traveled (miles traveled by gallons used), your figure may be different than displayed for the following reasons: •...
Page 132 Driver Controls Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a tone for one second when you have approximately 80 km (50 miles) to empty.
Page 133 Driver Controls Easy exit seat (if equipped) This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy exit seat feature, select this function from the SETUP control for the current display mode. 2.
Page 134 Driver Controls Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Pressing the RESET control cycles the message center through each of the language choices. 3. Press and hold the RESET control to set the language choice. Units (English/Metric) 1.
Page 135 Driver Controls The sequence of the system check report and how it appears in the message center is as follows: 1. FUEL LEVEL 2. WASHER FLUID LEVEL 3. ADVANCETRAC (if equipped) 4. ENGINE TEMP 5. OIL PRESSURE 6. TIRE PRESSURE SYSTEM (if equipped) 7.
Page 136 Driver Controls This acts as a reminder that these warning conditions still exist within the vehicle. Warning display Status Check backup aid (if equipped) Warning displays when R (reverse) gear is selected. PRNDL error no backup aid (if equipped) Door ajar Warning returns after 10 minutes Liftgate or liftglass ajar Warning-tire very low (if...
Page 137 Driver Controls DOOR AJAR. Displayed when a door is not completely closed. LIFTGATE OR LIFTGLASS AJAR. Displayed when the liftgate is not completely closed. CHECK ENGINE TEMPERATURE. Displayed when the engine coolant is overheating. Stop the vehicle as soon as safely possible, turn off the engine and let it cool.
Page 138 Driver Controls CHECK CHARGING SYSTEM. Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible.
Page 139 Driver Controls DATA ERR. These messages indicate improper operation of the vehicle network communication between electronic modules. • Fuel computer • Charging system • Door sensor • Washer fluid • Brake fluid • Compass • Outside temperature • Engine sensor Contact your dealer as soon as possible if these messages occur on a regular basis.
Page 140 Driver Controls CENTER CONSOLE (IF EQUIPPED) The center console offers several useful storage features. These include: 1. Pen holder 2. Tissue holder 3. Cassette/CD organizer slots 4. Large utility compartment 5. PalmPilot /PDA holder 6. Cupholders 7. Coin holder slots 8.
Page 141 Driver Controls POSITIVE RETENTION FLOOR MAT (IF EQUIPPED) Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal.
Page 142 Driver Controls LUGGAGE RACK The rear cross-bar can be adjusted to fit the item being carried. The front cross-bar does not move. To adjust the luggage rack, push the adjustment lever forward (toward the front of the vehicle), then slide the cross-bar forward and lock the adjusting levers by pushing them down (toward the back of the...
Page 143: Locks And Security
Locks and Security Locks and Security KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency.
Page 144 Locks and Security REMOTE ENTRY SYSTEM This device complies with part 15 of the FCC rules and with RS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
Page 145 Locks and Security Locking the doors/liftgate Press this control to lock all doors and liftgate. The park/turn signal lamps will flash once. To confirm all doors are closed and locked, press the control a second time within three seconds; the park/turn signal lamps will flash once and the horn will chirp.
Page 146 Locks and Security Memory feature (if equipped) The remote entry system can also control the memory feature. Press the control once to unlock the driver’s door. Pressing the control will automatically move the seat, rearview mirrors, and adjustable pedals to the desired memory position (the memory position corresponds to the transmitter being used).
Page 147 Locks and Security Replacing the battery The remote transmitter is powered by one coin type three-volt lithium battery CR2032 or equivalent. Typical operating range will allow you to be up to 10 meters (33 feet) away from your vehicle. A decrease in operating range can be caused by the following factors: •...
Page 148 Locks and Security Programming remote transmitters It is necessary to have all (maximum of four — original and/or new) of your remote transmitters available prior to beginning this procedure. To program the transmitters yourself: • Unlock all doors using the power door lock/unlock control.
Page 149 For vehicles not equipped with a message center, the feature may be deactivated by taking your vehicle to an authorized Ford dealer. Power door lock disable feature This feature will help protect your vehicle from unauthorized entry.
Page 150 Locks and Security KEYLESS ENTRY SYSTEM With the keyless entry keypad, you can: • lock or unlock the vehicle doors without using the key. Your vehicle has a factory set 5 digit code that operates the keyless entry system. You can also program your own 5 digit personal entry code.
Page 151 Locks and Security If you wish to erase your personal code, use the following instructions: 1. Enter factory set code. 2. Press 1/2 control and release. The system will now only respond to the factory set code. Anti-scan feature The anti-scan feature prevents repeated attempts at arriving at a valid key code.
Page 152 The SecuriLock passive anti-theft system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. THEFT INDICATOR The theft indicator is the flashing red indicator located on the dash panel.
Page 153 OFF and restart the engine with all other objects on the key ring held away from the ignition key. Check to make sure the coded key is an approved Ford coded key. If your keys are lost or stolen you will need to do the following: •...
Page 154 Locks and Security Replacing coded keys can be very costly and you may want to store an extra programmed key away from the vehicle in a safe place to prevent an unforeseen inconvenience. The correct coded key must be used for your vehicle. The use of the wrong type of coded key may lead to a “no start”...
Page 155 Locks and Security 5. Within 10 seconds of removing the second coded key, insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from 1 (OFF) to 3 (ON) (maintain ignition in 3 (ON) for at least one second, but no more than ten seconds).
Page 156: Seating And Safety Restraints
Seating and Safety Restraints Seating and Safety Restraints SEATING Adjusting the front manual seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to reduce the risk of injuring people in a collision or sudden stop.
Page 157 Seating and Safety Restraints Pull the seatback handle up to recline the seat. Using the armrest (if equipped) Push the release control to move the armrest up or down.
Page 158 Seating and Safety Restraints Using the manual lumbar support The lumbar support control is located on the outboard side of the seat. Turn the lumbar support control forward for more support. Turn the lumbar support backward for less support. Adjusting the front power seat (if equipped) Never adjust the driver’s seat or seatback when the vehicle is moving.
Page 159 Seating and Safety Restraints Press the control to move the seat forward, backward, up or down. Memory seats/rearview mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, outside rearview mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the driver door.
Page 160 Seating and Safety Restraints CLIMATE CONTROLLED SEATS (if equipped) The controls for the climate controlled seats are located on the center console. To operate the climate controlled seats the engine must be running. • Push the icon on the button to activate cooled seats.
Page 161 Seating and Safety Restraints • There is a filter located under both front seats. • It can be accessed from the second row seat. Move the front seat all the way forward and up to ease access. To remove climate controlled seat air filter: •...
Page 162 Seating and Safety Restraints To install climate controlled seat air filter: • First, position the filter in it’s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position.
Page 163 Seating and Safety Restraints For assistance, refer to the label located on the side of the seat cushion. Adjusting the 2nd row outboard seat for E-Z Entry The 2nd row outboard seats allow for easier entry and exit to and from the 3rd row seat.
Page 164 Seating and Safety Restraints 3. To return the seat to a seating position, push down on the seat until the seat is latched to the floor. 4. Lift the seatback to the upright position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty.
Page 165 Seating and Safety Restraints 3. Locate the latch strap at the front of the seat and pull to release the seat into a kneel down load floor position. A moderate force may be required to move the seat forward and down. Once the second row seats are in the down position, the front seats may be readjusted.
Page 166 Seating and Safety Restraints The rear latch hooks must be properly engaged with the floor striker. Position the rear legs of the seat over the floor strikers and engage. Folding the 20% seat system (if equipped) 1. Locate the release strap located between the front cushion and the seat back, and pull the strap to release the folding seat latch.
Page 167 Seating and Safety Restraints 3. To return the seat to the upright position, lift the seatback until the latch is fully engaged. Adjusting the second row 20% seat (if equipped) Lift the handle to move the seat forward or backward. Note: This seat can be moved forward to keep a child in a child restraint close to the front seat occupants.
Page 168 Seating and Safety Restraints Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe personal injuries in the event of a collision. Third row seats Ensure that no objects such as books, purses or briefcases are on the floor in front of the third row seats or on the seat cushion before lowering them.
Page 169 Seating and Safety Restraints Third row power folding seat (if equipped) The control buttons are located on the right-hand rear quarter trim panel (accessible from the liftgate area). Push the bottom portion of the control button to lower the desired seatback.
Page 170 Seating and Safety Restraints Third row adjustable head restraints Your vehicle’s third row outboard seating positions are equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision.
Page 171: Safety Restraints
Seating and Safety Restraints SAFETY RESTRAINTS Personal Safety System The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of air bag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations.
Page 172 Seating and Safety Restraints Driver and passenger dual-stage air bag supplemental restraints The dual-stage air bags offer the capability to tailor the level of air bag inflation energy. A lower, less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts.
Page 173 Seating and Safety Restraints Determining if the Personal Safety System is operational The Personal Safety System uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the Warning Light section in the Instrument Cluster chapter. Routine maintenance of the Personal Safety System is not required.
Page 174 Seating and Safety Restraints All occupants of the vehicle, including the driver, should always properly wear their safety belts, even when an air bag (SRS) is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
Page 175 Seating and Safety Restraints Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. •...
Page 176 Seating and Safety Restraints The front outboard, rear outboard, and second and third row center safety restraints in the vehicle are combination lap and shoulder belts. The front center safety restraint (if equipped) is a manually-adjustable lap belt. All of the passenger lap and shoulder belts have two types of locking modes described below: Vehicle sensitive mode This is the normal retractor mode, which allows free shoulder belt length...
Page 177 Seating and Safety Restraints 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Page 178 Seating and Safety Restraints When the Safety Canopy system and/or the front airbags are activated, the safety belt pretensioners for the driver and right front passenger seating positions will be activated when the respective seatbelt is properly buckled. The driver and the right front passenger seat belt system (including retractors, buckles and height adjusters) must be replaced if the vehicle is involved in a collision that results in deployment of front air bags or Safety Canopy...
Page 179 Seating and Safety Restraints First row center lap belt (if equipped) Adjusting the lap belt The lap belt should fit snugly and as low as possible around the hips, not across the waist. The lap belt does not adjust automatically. Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming...
Page 180 Seating and Safety Restraints Conditions of operation If... Then... The driver safety belt is not The safety belt warning light buckled before the ignition switch illuminates 1-2 minutes and the is turned to the ON position... warning chime sounds 4-8 seconds. The driver safety belt is buckled The safety belt warning light and while the indicator light is...
Page 181 Seating and Safety Restraints The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider... “Crashes are rare events” 36 700 crashes occur every day. The more we drive, the more we are exposed to “rare”...
Page 182 Seating and Safety Restraints Reasons given... Consider... “I have an air bag” Air bags offer greater protection when used with safety belts. Frontal airbags are not designed to inflate in rear and side crashes or rollovers. “I’d rather be thrown clear” Not a good idea.
Page 183 Seating and Safety Restraints 1. Turn the ignition switch to the RUN (or ON) position. (DO NOT START THE ENGINE) 2. Wait until the safety belt warning light turns off. (Approximately 1–2 minutes) • Steps 3–5 must be completed within 60 seconds or the procedure will have to be repeated.
Page 184: Air Bags
(if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a collision. Ford Motor Company recommends that all safety belt assemblies used in vehicles involved in a collision be replaced.
Page 185 Seating and Safety Restraints Important SRS precautions The SRS is designed to work with the safety belt to help protect the driver and right front passenger from certain upper body injuries. Air bags DO NOT inflate slowly; there is a risk of injury from a deploying air bag.
Page 186 Seating and Safety Restraints Do not attempt to service, repair, or modify the air bag supplemental restraint systems or its fuses. See your Ford or Lincoln Mercury dealer. The front passenger air bag is not designed to offer protection to an occupant in the center front seating position.
Page 187 Seating and Safety Restraints How does the air bag supplemental restraint system work? The air bag SRS is designed to activate when the vehicle sustains longitudinal deceleration sufficient to cause the sensors to close an electrical circuit that initiates air bag inflation.
Page 188 Seating and Safety Restraints Several air bag system components get hot after inflation. Do not touch them after inflation. If the air bag has deployed, the air bag will not function again and must be replaced immediately. If the air bag is not replaced, the unrepaired area will increase the risk of injury in a collision.
Page 189 Do not attempt to service, repair, or modify the Safety Canopy system, its fuses, the A, B, or C pillar trim, or the headliner on a vehicle containing a Safety Canopy . See your Ford or Lincoln Mercury dealer. All occupants of the vehicle including the driver should always...
Page 190 Seating and Safety Restraints How does the Safety Canopy system work? The design and development of the Safety Canopy system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Air Bag Technical Working Group.
Page 191 Seating and Safety Restraints The Safety Canopy is mounted to roof side-rail sheet metal, behind the headliner, above the first and second row seats. In certain lateral collisions or rollover events, the Safety Canopy system will be activated, regardless of which seats are occupied. In certain rollover events, the Safety Canopy on both sides of the vehicle will be inflated, regardless of which seats are occupied.
Page 192 Seating and Safety Restraints Determining if the system is operational The SRS uses a readiness light in the instrument cluster or a tone to indicate the condition of the system. Refer to the Air bag readiness section in the Instrument Cluster chapter. Routine maintenance of the air bag is not required.
Page 193 To improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster. Booster seats position a child so that safety belts fit better. They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably.
Page 194 Seating and Safety Restraints When children should use booster seats Children need to use booster seats from the time they outgrow the toddler seat until they are big enough for the vehicle seat and lap/shoulder belt to fit properly. Generally this is when they weigh about 80 lbs (about 8 to 12 years old).
Page 195 Seating and Safety Restraints • Those with a high back. If, with a backless booster seat, you cannot find a seating position that adequately supports your child’s head, a high back booster seat would be a better choice. Both can be used in any vehicle in a seating position equipped with lap/shoulder belts if your child is over 40 lbs.
Page 196 Seating and Safety Restraints SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’s instructions with the safety seat you put in your vehicle. If you do not install and use the safety seat properly, the child may be injured in a sudden stop or collision.
Page 197 Ford recommends the use of a child safety seat having a top tether strap and LATCH attachments. Install the child safety seat in a seating position which is capable of providing tether and LATCH anchors.
Page 198 Seating and Safety Restraints 2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together. 3. While holding the shoulder and lap belt portions together, route the tongue through the child seat according to the child seat manufacturer’s instructions.
Page 199 Seating and Safety Restraints 5. To put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode.
Page 200 Seating and Safety Restraints Installing child safety seats in the center front seating position Always transport children 12 years old and under in the rear seats and always properly use appropriate child restraints. It is safer to install child safety seats in seating positions that have child seat anchors.
Page 201 Seating and Safety Restraints The tether strap anchors in your vehicle are in the following positions (shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown.
Page 202 Seating and Safety Restraints • center seating position (if equipped) 3. Route the child safety seat tether strap under the head restraint (outboard seats) and over the back of the seat. 4. Grasp the tether strap and position it to the seat frame. 5.
Page 203 Seating and Safety Restraints 6. Rotate the tether strap clip. 7. Tighten the child safety seat tether strap according to the manufacturer’s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cushion. 2.
Page 204 Seating and Safety Restraints 4. Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly, the child safety seat may not be retained properly in the event of a collision. 5. Refer to the Installing child safety seats in combination lap and shoulder belt seating positions section of this chapter for...
Page 205 Seating and Safety Restraints Your vehicle has LATCH anchors for child seat installation at the seating positions marked with the child seat symbol: Never attach two LATCH child safety seats to the same anchor. In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death.
Page 206 Seating and Safety Restraints Attach LATCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LATCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it.
Page 207: Driving
Driving Driving STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 2. ACCESSORY, allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational.
Page 208 Driving If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine.
Page 209 Driving 5. Turn the key to 3 (ON) without turning the key to 4 (START). Make sure the corresponding lights illuminate or illuminate briefly. If a light fails to illuminate, have the vehicle serviced. • If the driver’s safety belt is fastened, the light may not illuminate.
Page 210: Brakes
Driving Note: If the engine does not start within five seconds on the first try, turn the key to OFF, wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off in case the engine is flooded with fuel.
Page 211 Driving “continuous squeal” sound is present while braking, the brake linings may be worn-out and should be inspected by a qualified service technician. If you are driving down a long or steep hill, shift to a lower gear. Do not apply your brakes continuously, as they may overheat and become less effective.
Page 212 Driving • We recommend that you familiarize yourself with this braking technique. However, avoid taking any unnecessary risks. ABS warning lamp warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced.
Page 213 Driving Always set the parking brake fully and make sure that the gearshift is securely latched in P (Park). The parking brake is not recommended to stop a moving vehicle. However, if the normal brakes fail, the parking brake can be used to stop your vehicle in an emergency.
Page 214: Air Suspension
Driving Speed sensitive steering Your vehicle is equipped with engine speed sensitive steering. At higher engine speeds associated with high vehicle speed, the steering assist will decrease to improve steering feel. If the amount of effort required to steer your vehicle changes while maintaining a constant engine speed, have the power steering system checked by your dealer or a qualified service technician.
Page 215 Driving The air suspension shut-off switch is located behind two access panels on the left rear quarter trim panel, near the liftgate. To remove the first panel, turn the control counterclockwise and remove the panel. On vehicles equipped with air suspension, turn the air suspension and the ignition switch off prior to jacking, hoisting or towing your vehicle.
Page 216 Driving Press the bottom portion of the switch to turn off the air suspension. LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited slip axle functions like a standard rear axle.
Page 217 Driving Vehicles with a higher center of gravity such as utility and four-wheel drive vehicles handle differently than vehicles with a lower center of gravity. Utility and four-wheel drive vehicles are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to perform satisfactorily under off-road conditions.
Page 218 Driving AdvanceTrac enhances your vehicle’s stability during maneuvers that require all available tire traction, like in wet/snowy/icy road conditions and/or when performing emergency maneuvers. In an emergency lane-change, the driver will experience better overall vehicle traction, and have better control of the vehicle. The AdvanceTrac system helps the driver maintain steering control if the vehicle begins to slide excessively left or right or spin out.
Page 219 Driving indicator light in the instrument cluster remains on while the engine is running, have the system serviced immediately. Pressing the control once will disable the AdvanceTrac stability enhancement and the engine power reduction portion of the traction enhancement feature; the brake portion of the traction enhancement feature will still function normally.
Page 220: Transmission Operation
Driving AUTOMATIC TRANSMISSION OPERATION Brake-shift interlock This vehicle is equipped with a park/brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignition is in the ON position unless brake pedal is depressed. If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed, or when the ignition is in the OFF position, it is possible that a fuse has blown or the vehicle’s brakelamps are not operating properly.
Page 221 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.
Page 222 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) With the gearshift lever in R (Reverse), the vehicle will move backward.
Page 223 Driving • additional engine downhill braking is desired. If towing a trailer, refer to Driving while you tow in the Trailer towing section. To return to (Overdrive) mode, press the transmission control switch (TCS). The TCIL will no longer be illuminated. Each time the vehicle is started, the transmission will automatically return to normal overdrive mode.
Page 224 Driving REVERSE SENSING SYSTEM (IF EQUIPPED) The RSS sounds a tone to warn the driver of obstacles near the rear bumper when R (Reverse) is selected. The RSS will assist the driver in detecting certain objects while: • the vehicle is moving toward a stationary object at a speed of 5 km/h (3 mph) or less.
Page 225 Driving The RSS detects obstacles up to 2 meters (6 ft.) from the rear bumper with a decreased coverage area at the outer corners of the bumper, (refer to the figures for approximate zone coverage areas). As you move closer to the obstacle, the rate of the tone increases.
Page 226 The Control Trac system indicator lights illuminate only under the following conditions. If these lights illuminate when driving in 2H or A4WD, contact your Ford dealer as soon as possible. • 4X4 HIGH - momentarily illuminates when the vehicle is HIGH started.
Page 227 Driving • 4H (4X4 HIGH) provides mechanically locked four-wheel drive power to front and rear wheels. The “4X4” light will illuminate in the instrument cluster when this position is selected. This position is not recommended for use on dry pavement. This position is only intended for severe winter or off-road conditions, such as deep snow, ice or shallow sand.
Page 228 Driving Using the Control Trac system Shifting from 2H to A4WD or 4H Move the control to the A4WD or 4H position at any forward speed up to 88 km/h (55 mph). The “4X4” light in the instrument cluster will illuminate if 4H is selected.
Page 229 Driving Shifting from 4L to 4H, A4WD or 2H 1. Bring the vehicle to a stop and keep the brake pedal depressed. 2. Place the gearshift in N (Neutral). 3. Move the control to the 4H, A4WD or 2H position. Note: Some noise may be heard as the system shifts or engages.
Page 230 Driving Basic operating principles • Do not use 4H (4x4 HIGH) or 4L (4x4 LOW) on dry, hard surfaced roads. This may damage the drivelines and axles. • Drive slower in strong crosswinds which can affect the normal steering characteristics of your vehicle. •...
Page 231 Driving Always set the parking brake fully and make sure the gearshift is latched in P (Park). Turn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly.
Page 232 Driving Control Trac four–wheel drive system When a four–wheel drive mode is selected, the Control Trac system uses all four wheels to power the vehicle. This increases traction, enabling you to drive over terrain and road conditions that a conventional two-wheel drive vehicle cannot.
Page 233 Ford Motor Company joins the U.S. Forest Service and the Bureau of Land Management in encouraging you to help preserve our national forest and...
Page 234 Driving Driving on hilly or sloping terrain Although natural obstacles may make it necessary to travel diagonally up or down a hill or steep incline, you should always try to drive straight up or straight down. Avoid driving crosswise or turning on steep slopes or hills.
Page 235 Ford or Lincoln/Mercury dealer. If you nevertheless decide to equip your four–wheel drive for off-road use with tires larger than what Ford Motor Company recommends, you should not use these tires for highway driving. If you use any tire/wheel combination not recommended by Ford Motor...
Page 236 (a label may also be found on the fuel cap filler door). Failure to follow tire pressure recommendations can adversely affect the way your vehicle handles. Do not exceed the Ford Motor Company recommended pressure even if it is less than the maximum pressure allowed for the tire.
Page 237: Vehicle Loading
Driving Ford Motor Company recommends that caution be used with any vehicle equipped with a high load or device (such as ladder racks or pickup box cover). Failure to maintain your vehicle properly may void the warranty, increase your repair cost, reduce vehicle performance and operational capabilities and adversely affect driver and passenger safety.
Page 238 Driving • GAWR (Gross Axle Weight Rating): Carrying capacity for each axle system. The GAWR is specific to each vehicle and is listed on the Safety Certification Label on the driver’s door pillar. • GCW (Gross Combined Weight): The combined weight of the towing vehicle (including occupants and cargo) and the loaded trailer.
Page 239 Driving Always ensure that the weight of occupants, cargo and equipment being carried is within the weight limitations that have been established for your vehicle including both gross vehicle weight and front and rear gross axle weight rating limits. Under no circumstance should these limitations be exceeded.
Page 240: Trailer Towing
(when a customer provided controller is installed) and ground. A kit containing a wiring harness/adapter and installation instructions to attach an electric brake controller may be obtained from any Ford or Lincoln/Mercury dealer (part number 2L1Z–14A348–AB). Before towing a trailer, make sure the trailer brakes (if equipped) and lamps are properly connected and functional.
Page 241 Driving Trailer weight Rear axle Maximum GCWR - range (0 - Engine ratio kg (lbs.) maximum) kg (lbs.) 4.6L 4762 (10500) 0-2268 (0-5000) 5.4L 6577 (14500) 0–4060 (0–8950) 4.6L 4853 (10700) 0-2268 (0-5000) 5.4L 6577 (14500) 0–3924 (0–8650) Maximum frontal area of trailer is 5.6 square meters (60 square feet) Do not exceed the maximum loads listed on the Safety Compliance Certification label.
Page 242 Driving • Weight distributing - requires an aftermarket weight distributing system which includes draw bar, hitch ball, spring bars and snap-up brackets. The vertical tongue load of the trailer is distributed between the truck and the trailer by this system. Mode Maximum Maximum...
Page 243 Driving 4. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within 0–13 mm (0.5 in) of the reference point. After proper adjustment, the rear bumper should be no higher than in Step 3. 5.
Page 244 Driving • Consult your local motor vehicle speed regulations for towing a trailer. • To eliminate excessive shifting, use a lower gear. This will also assist in transmission cooling. (For additional information, refer to the Understanding the positions of the 4–speed automatic transmission section in this chapter.
Page 245 If a distance of 80 km (50 miles) or a speed of 56 km (35 mph) must be exceeded, the drive shaft will have to be removed before the vehicle is towed. Ford recommends the driveshaft be removed/installed only by a qualified technician. See your local dealer for driveshaft removal/installation. Improper removal/installation of the driveshaft can cause transmission fluid loss, damage to the driveshaft and internal transmission components.
Page 246: Roadside Emergencies
Roadside Emergencies Roadside Emergencies GETTING ROADSIDE ASSISTANCE To fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New Vehicle Limited Warranty. The service is available: •...
Page 247 Roadside Emergencies Canadian customers who require roadside assistance, call 1–800–665–2006. If you need to arrange roadside assistance for yourself, Ford Motor Company will reimburse a reasonable amount. To obtain reimbursement information, U.S. Ford or Mercury vehicles customers call 1-800-241-3673; Lincoln vehicle customers call 1–800–521–4140.
Page 248: Fuel Pump Shut-Off Switch
Roadside Emergencies FUEL FUEL PUMP SHUT-OFF SWITCH RESET This device stops the electric fuel pump from sending fuel to the engine when your vehicle has had a substantial jolt. After an accident, if the engine cranks but does not start, this switch may have been activated.
Page 249 Roadside Emergencies The fuel pump shut-off switch has a red reset button on top of it and is located beneath the air suspension switch (if equipped). If the vehicle is not equipped with air suspension, the fuel pump shut-off switch’s red reset button will still be visible behind this access panel.
Page 250: Fuses And Relays
Roadside Emergencies FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating.
Page 251 Roadside Emergencies Passenger compartment fuse panel / power distribution box The fuse panel is located under the right-hand side of the instrument panel. To remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it.
Page 252 Roadside Emergencies The fuses are coded as follows. Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 10A* Run/Accessory - Front wiper motor, Instrument cluster, Rear wiper motor, Tire Pressure Monitor System (TPMS) module 20A* Turn signal/Hazard flasher, Stoplamp switch, IVD (AdvanceTrac) stoplamps relay, Stoplamps, Center high-mount stop light (CHMSL), Turn signal...
Page 253 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 15A* DVD player, Rear seat audio controls, CDDJ (navigation radio) 7.5A* Powertrain Control Module (PCM) (KA power), Speed control deactivation switch, Manual climate control mode switch, Stoplamp switch, Brake-shift interlock (BSI) solenoid, EATC control head, Body Security Module (BSM) (KA power),...
Page 254 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 10A* A/C compressor clutch relay, A/C compressor clutch solenoid, Air suspension compressor relay, 4x4 Integrated Wheel Ends (IWE) solenoid 10A* Speed control servo, Speed control relay 10A* Manual climate control mode switch, Rear window defroster relay coil, A/C refrigerant containment switch, A/C...
Page 255 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 10A* Auxiliary A/C temperature blend door actuator, Auxiliary A/C front auxiliary control, Turn signal flasher, Electrochromatic mirror, Auxiliary mode motor, Climate controlled seat modules 10A* Restraints Control Module (RCM) 30A* Air suspension module (air spring solenoids and height sensors), 4x4...
Page 256 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Compass module, Reverse sensing system module, Brake shift interlock (BSI) solenoid, Overdrive cancel switch, Air suspension module (Run/Start sense) PCM relay coil, Speed control relay coil, SecuriLock transceiver 30A* Trailer tow electric brake controller, Trailer tow 7–wire...
Page 257 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 25A* Rear wiper motor, Washer pump (rear window wash) 20A* Console power points (front and rear of console), Instrument panel power point (bench seat) 20A* DRL relays, DRL foglamps, DRL headlamp relay coil, Headlamp switch (headlamps), Multifunction switch (flash-to-pass), BSM...
Page 258 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description 30A** Driver seat motor switch (non-memory), Memory module, Power memory mirrors, Adjustable pedals switch and motor 30A** Spare 50A** Air suspension compressor, Air suspension compressor relay 30A** ABS/AdvanceTrac module (valves) 30A**...
Page 259 Roadside Emergencies Fuse/Relay Fuse Amp Passenger Compartment Fuse Location Rating Panel Description Hi-beam relay Fuse # 35, Hi-beam headlamps, Hi-beam indicator Rear window Fuse 8 (heated mirrors), Rear defrost relay window defroster, Heated outside mirrors, Rear window defroster indicator (climate control head) Trailer tow Trailer tow 7–wire connector battery charge...
Page 260 Roadside Emergencies CHANGING THE TIRES If you get a flat tire while driving, do not apply the brake heavily. Instead, gradually decrease your speed. Hold the steering wheel firmly and slowly move to a safe place on the side of the road. The use of tire sealants is not recommended and may compromise the integrity of your tires.
Page 261 Roadside Emergencies Removing the spare tire 1. Fold the rear seat down. Refer to Rear seats in the Seating and safety restraints chapter. 2. Remove the jack handle and winch extension from the tray and assemble them. 3. Open the spare tire winch access plug in the bottom of the compartment located behind the 3rd row seat, very close to the jack and...
Page 262 Roadside Emergencies 1. Park on a level surface, activate hazard flashers and set the parking brake. 2. Place gearshift lever in P (Park), turn engine OFF and block the diagonally opposite wheel. (If changing the tire on a grade, block the diagonally opposite wheel on the downward side of the grade.) 3.
Page 263 Roadside Emergencies When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park). To prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and the diagonally opposite wheel is blocked.
Page 264 Roadside Emergencies • Never use the front or rear differential as a jacking point. 6. Remove the lug nuts with the lug wrench. 7. Replace the flat tire with the spare tire, making sure the valve stem is facing outward. Reinstall the lug nuts until the wheel is snug against the hub.
Page 265: Jump Starting
Roadside Emergencies 5. Disassemble the tools and snap them back into the tool tray. Close the access hole with the rubber plug. Reinstall the tray into the vehicle and secure it with the wing nut (turn clockwise until tight). JUMP STARTING YOUR VEHICLE The gases around the battery can explode if exposed to flames, sparks, or lit cigarettes.
Page 266 Roadside Emergencies Connecting the jumper cables 1. Connect the positive (+) jumper cable to the positive (+) terminal of the discharged battery. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery.
Page 267 Roadside Emergencies 4. Make the final connection of the negative (-) cable to the jump starting stud located in the rear of the engine compartment, near the battery. Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped.
Page 268 Roadside Emergencies Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the ground metal surface. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery. 2.
Page 269 Roadside Emergencies 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’s battery. 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’s battery. After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions.
Page 270: Wrecker Towing
It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. On 4x2 vehicles, it is acceptable to tow the vehicle with the front wheels on the ground (without dollies) and the rear wheels off the ground.
Page 271 • Do not exceed a distance of 80 km (50 miles). • Do not exceed 56 km/h (35 mph) vehicle speed. Ford Motor Company produces a towing manual for all authorized tow truck operators. Have your tow truck operator refer to this manual for...
Page 272: Customer Assistance
Ford Customer Relationship Center. Away from home If you own a Ford or Mercury vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 273 If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Relationship Center to find an authorized dealership to help you.
Page 274 5,000 participating Ford or Lincoln Mercury and Ford of Canada dealers. If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www.ford-esp.com.
Page 275 THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes. • available free to owners and lessees of qualifying Ford Motor Company vehicles. The Dispute Settlement Board may not be available in all states. Ford...
Page 276 • The name of the dealer(s) who sold or serviced the vehicle. • A brief description of your unresolved concern. • A brief summary of the action taken by the dealer(s) and Ford Motor Company. • The names (if known) of all the people you contacted at the dealership(s).
Page 277 After a case is reviewed, the Board mails you a decision letter and a form on which to accept or reject the Board’s decision. The decisions of the Board are binding on Ford (and, in some cases, on the dealer) but not on consumers who are free to pursue other remedies available to them under state or federal law.
Page 278 UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) In those cases where you continue to feel that the efforts by Ford and the dealer to resolve a factory-related vehicle service concern have been unsatisfactory, Ford of Canada participates in an impartial third party mediation/arbitration program administered by the Canadian Motor Vehicle Arbitration Plan (CAMVAP).
Page 279 If your vehicle must be serviced while you are traveling or living in Central or South America, the Caribbean, or the Middle East, contact the nearest Ford dealership. If the dealership cannot help you, write or call: FORD MOTOR COMPANY...
Page 280 In the case of 1 or 2 above, the consumer must also notify the manufacturer of the need for the repair of the nonconformity at the following address: Ford Motor Company 16800 Executive Plaza Drive Mail Drop 3NE-B Dearborn, MI 48126...
Page 281: Reporting Safety Defects (U.s. Only)
However, NHTSA cannot become involved in individual problems between you, your dealer, or Ford Motor Company. To contact NHTSA, you may either call the Auto Safety Hotline toll-free at 1–800–424–9393 (or 366–0123 in the Washington D.C.
Page 282: Cleaning
Cleaning Cleaning WASHING THE EXTERIOR Wash your vehicle regularly with cool or lukewarm water and a neutral Ph shampoo, such as Motorcraft Detail Wash (ZC-3–A), which is available from your dealer. • Never use strong household detergents or soap, such as dish washing or laundry liquid.
Page 283 Cleaning PAINT CHIPS Your dealer has touch-up paint and sprays to match your vehicle’s color. Take your color code (printed on a sticker in the driver’s door jam) to your dealer to ensure you get the correct color. • Remove particles such as bird droppings, tree sap, insect deposits, tar spots, road salt and industrial fallout before repairing paint chips.
Page 284 Cleaning • Cover the highlighted areas to prevent water damage when cleaning the engine. • 4.6L V8 engine • 5.4L V8 engine • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage.
Page 285 Cleaning PLASTIC (NON-PAINTED) EXTERIOR PARTS Use only approved products to clean plastic parts. These products are available from your dealer. • For routine cleaning, use Motorcraft Detail Wash (ZC-3–A). • If tar or grease spots are present, use Motorcraft Bug and Tar Remover (ZC-42).
Page 286 Cleaning INTERIOR For fabric, carpets, cloth seats and safety belts: • Remove dust and loose dirt with a vacuum cleaner. • Remove light stains and soil with Motorcraft Extra Strength Upholstery Cleaner (ZC-41). • If grease or tar is present on the material, spot-clean the area first with Motorcraft Spot and Stain Remover (ZC-14).
Page 287 Cleaning FORD, LINCOLN AND MERCURY CAR CARE PRODUCTS Your Ford, Lincoln or Mercury dealer has many quality products available to clean your vehicle and protect its finishes. These quality products have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and appearance of your vehicle.
Page 288: Maintenance And Specifications
Maintenance and Specifications Maintenance and Specifications SERVICE RECOMMENDATIONS To help you service your vehicle: • We highlight do-it-yourself items in the engine compartment for easy location. • We provide a scheduled maintenance guide which makes tracking routine service easy. If your vehicle requires professional service, your dealership can provide the necessary parts and service.
Page 289 Maintenance and Specifications OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood.
Page 290: Engine Compartment
Maintenance and Specifications IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8.
Page 291 Maintenance and Specifications 5.4L V8 engines 1. Battery 2. Automatic transmission fluid dipstick 3. Engine oil filler cap 4. Power steering fluid reservoir 5. Engine oil dipstick 6. Brake fluid reservoir 7. Engine coolant reservoir 8. Air filter assembly 9. Windshield washer fluid reservoir...
Page 292: Engine Oil
In very cold weather, do not fill the reservoir completely. Only use a washer fluid that meets Ford specification WSB-M8B16–A2. Refer to Lubricant specifications in this chapter. State or local regulations on volatile organic compounds may restrict the use of methanol, a common windshield washer antifreeze additive.
Page 293 Maintenance and Specifications 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4. Open the hood. Protect yourself from engine heat. 5. Locate and carefully remove the engine oil level indicator (dipstick). 6. Wipe the indicator clean. Insert the indicator fully, then remove it again.
Page 294 Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). To protect your engine’s warranty use Motorcraft SAE 5W-20 or an equivalent 5W-20 oil meeting Ford specification WSS-M2C153–H. SAE 5W-20 oil provides optimum fuel economy and durability performance meeting all requirements for your vehicle’s engine.
Page 295: Battery
Maintenance and Specifications Ford production and aftermarket (Motorcraft) oil filters are designed for added engine protection and long life. If a replacement oil filter is used that does not meet Ford material and design specifications, start-up engine noises or knock may be experienced.
Page 296 Maintenance and Specifications Batteries normally produce explosive gases which can cause personal injury. Therefore, do not allow flames, sparks or lighted substances to come near the battery. When working near the battery, always shield your face and protect your eyes. Always provide proper ventilation.
Page 297 Maintenance and Specifications Because your vehicle’s engine is also electronically controlled by a computer, some control conditions are maintained by power from the battery. When the battery is disconnected or a new battery is installed, the engine must relearn its idle and fuel trim strategy for optimum driveability and performance.
Page 298 Maintenance and Specifications ENGINE COOLANT Checking engine coolant The concentration and level of engine coolant should be checked at the mileage intervals listed in the scheduled maintenance guide. The coolant concentration should be maintained at 50/50 coolant and distilled water, which equates to a freeze point of -36°...
Page 299 If sprayed on the windshield, engine coolant could make it difficult to see through the windshield. • Add Motorcraft Premium Gold Engine Coolant (yellow-colored), VC-7–A (VC-7–B in Oregon), meeting Ford Specification WSS-M97B51–A1. Note: Use of Motorcraft Cooling System Stop Leak Pellets, VC-6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan.
Page 300 Maintenance and Specifications • A large amount of water without engine coolant may be added, in case of emergency, to reach a vehicle service location. In this instance, the cooling system must be drained and refilled with a 50/50 mixture of engine coolant and distilled water as soon as possible.
Page 301 Recycled engine coolant Ford Motor Company does NOT recommend the use of recycled engine coolant in vehicles originally equipped with Motorcraft Premium Gold Engine Coolant since a Ford-approved recycling process is not yet available.
Page 302 Maintenance and Specifications If you drive in extremely hot climates: • It is still necessary to maintain the coolant concentration above 40%. • NEVER decrease the coolant concentration below 40%. • Decreased engine coolant concentrations below 40% will decrease the corrosion protection characteristics of the engine coolant and may cause engine damage.
Page 303 Maintenance and Specifications When this occurs the vehicle will still operate. However: • The engine power will be limited. • The air conditioning system will be disabled. Continued operation will increase the engine temperature: • The engine will completely shut down. •...
Page 304 Maintenance and Specifications WHAT YOU SHOULD KNOW ABOUT AUTOMOTIVE FUELS Important safety precautions Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray and fire. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 305 Maintenance and Specifications • Avoid getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury.
Page 306 The customer warranty may be void for any damage to the fuel tank or fuel system if the correct genuine Ford or Motorcraft fuel filler cap is not used. The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap.
Page 307 Ask your fuel supplier about gasolines that meet the World-wide Fuel Charter. Cleaner air Ford endorses the use of reformulated “cleaner-burning” gasolines to improve air quality. Running out of fuel Avoid running out of fuel because this situation may have an adverse affect on powertrain components.
Page 308 Maintenance and Specifications • Your “Service Engine Soon” indicator may come on. For more information on the “Service Engine Soon” indicator, refer to the Instrument cluster chapter. Fuel Filter For fuel filter replacement, see your dealer or a qualified service technician.
Page 309 Maintenance and Specifications • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than 2 automatic click-offs when filling. • Always use fuel with the recommended octane rating. •...
Page 310 Maintenance and Specifications • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel economy. • Slow down gradually. •...
Page 311 Maintenance and Specifications • Using fuel blended with alcohol may lower fuel economy. • Fuel economy may decrease with lower temperatures during the first 12–16 km (8–10 miles) of driving. • Driving on flat terrain offers improved fuel economy as compared to driving on hilly terrain.
Page 312 Maintenance and Specifications If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.
Page 313 Check the power steering fluid. Refer to the scheduled maintenance guide for the service interval schedules. If adding fluid is necessary, use only Ford Premium Power Steering Fluid or MERCON ATF. 1. Start the engine and let it run until it reaches normal operating...
Page 314 Maintenance and Specifications BRAKE FLUID RESERVOIR The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range, there is no need to add fluid.
Page 315 Maintenance and Specifications Low fluid level Do not drive the vehicle if the fluid level is at the bottom of the dipstick and the ambient temperature is COLD DO NOT ADD above 10°C (50°F). Correct fluid level The transmission fluid should be checked at normal operating temperature 66°C-77°C (150°F-170°F) on a level surface.
Page 316 Maintenance and Specifications If an overfill occurs, excess fluid should be removed by a qualified technician. COLD DO NOT ADD An overfill condition of transmission fluid may cause shift and/or engagement concerns and/or possible damage. Do not use supplemental transmission fluid additives, treatments or cleaning agents.
Page 317 Maintenance and Specifications 2. Loosen the clamp that secures the air filter cover to the air filter housing and carefully separate the cover from housing. 3. Remove the air filter element from the air filter housing. 4. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover.
Page 318 10 to 12 inches or limited production tires as defined in Title 49 Code of Federal Regulations Part 575.104(c)(2). U.S. Department of Transportation-Tire quality grades: The U.S. Department of Transportation requires Ford to give you the following information about tire grades exactly as the government has written it. Treadwear...
Page 319 Maintenance and Specifications The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure. SERVICING YOUR TIRES Checking the tire pressure •...
Page 320 Make sure that all replacement tires are of the same size, type, speed rating, load-carrying capacity and tread design (e.g., “All Terrain”, “Touring”, etc.), as originally offered by Ford. Do not replace your tires with “high performance” tires or larger...
Page 321 Maintenance and Specifications Failure to follow these precautions may adversely affect the handling of the vehicle, and increase the risk of loss of vehicle control, vehicle rollover and/or personal injury. Tires that are larger or smaller than your vehicle’s original tires may also affect the accuracy of your speedometer.
Page 322: Changing Tires
Follow these guidelines when using snow tires and chains: • Use only cable type chains or chains offered by Ford as an accessory or equivalent. Other conventional link type chains may contact and cause damage to the vehicle’s wheel house and/or body.
Page 323: Part Numbers
EV-233 EV-238 Spark plugs* AGSF-32PM AGSF-22WM * Refer to Vehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford Part Application Capacity Name Brake fluid Motorcraft High Fill to line on Performance reservoir DOT 3 Motor...
Page 324 Maintenance and Specifications Fluid Ford Part Application Capacity Name Engine coolant Motorcraft 4.6L V8 engine 19.0L (20.1 Premium Gold with 1 row quarts) Engine Coolant radiator (yellow-colored) 5.4L V8 engine 21.0L (22.2 with 1 row quarts) radiator 4.6L V8 engine 21.0L (22.2...
Page 325 12mm (3/8 inch to 1/2 inch) below the bottom of the filler hole. Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 (or equivalent) meeting Ford specification EST-M2C118–A for complete refill of Limited Slip axles. For complete refills, fill using the Additive Friction Modifier...
Page 326: Lubricant Specifications
Maintenance and Specifications LUBRICANT SPECIFICATIONS Ford part Ford part Ford Item name number specification Hinges, latches, Multi-Purpose XG-4 or XL-5 ESR-M1C159-A striker plates Grease or ESB-M1C93-B and rotors, seat tracks, fuel filler door hinge and spring Lock cylinders, Penetrating and...
Page 327 Maintenance and Specifications Ford part Ford part Ford Item name number specification 4x4 front wheel High E8TZ-19590-A ESA-M1C198-A bearings, 4x4 Temperature spindle needle 4x4 Front Axle bearings, spindle & Wheel Bearing thrust bearings Grease & front drive axle u-joint/slip spline...
Page 328 Use of any fluid other than the recommended fluid may cause transmission damage. Add 118 ml (4 oz.) of Additive Friction Modifier XL-3 or equivalent meeting Ford specification EST-M2C118-A for complete refill of Ford Limited Slip rear axles. ENGINE DATA Engine 4.6L V8 engine...
Page 329 Maintenance and Specifications VEHICLE DIMENSIONS Vehicle dimensions 4x2 mm (in) 4x4 mm (in) (1) Overall length 5228 5228 (205.8) (205.8) (2) Vehicle width 2000 2000 (Body) (78.7) (78.7) (2) Vehicle width 2390 2390 including mirrors (94.1) (94.1) (2) Vehicle width 2029 2029 with mirrors folded...
Page 330 Maintenance and Specifications...
Page 331 Maintenance and Specifications IDENTIFYING YOUR VEHICLE Certification label The National Highway Traffic Safety Administration Regulations require that a Certification label be affixed to a vehicle and prescribe where the Certification label may be located. The Certification label is located on the front door latch pillar on the driver’s side.
Page 332: Accessories
Not all accessories are available for all models. Following is a list of several Ford Genuine Accessory products. Not all accessories are available for all models. To find out what accessories are available for your vehicle, please contact your dealer or visit our online store at: www.fordaccessoriesstore.com.
Page 333 Accessories Comfort and convenience Battery warmer Cargo organizers Cargo trays Carpeted cargo mat Dash trim (wood grain) Door edge guards Molded in color running boards Rear seat entertainment system – DVD Remote Start System Tail lamp surrounds (chrome, black and prime) Smoker’s pack Swivel hitch/quick step Travel equipment...
Page 334 Accessories Removable luggage rack adapters Roof rack cross bars Ski/snowboard carrier Soft luggage cover Trailer hitch bars and balls Trailer hitch receiver cover Protection and appearance equipment Air bag anti-theft locks Cargo liners, interior Carpet floor mats Fender flares Front end covers (full and sport) Full vehicle cover Hood deflectors Leather steering wheel...
Page 335 • Ford cannot assume responsibility for any adverse effects or damage that may result from the use of such equipment. • Do not install equipment which modifies the vehicles suspension or steering.
Page 336: Index
Index Index refill capacities ......322 ABS (see Brakes) .....210 Accessory delay ......113 Battery ........294 Air bag supplemental acid, treating emergencies ..294 restraint system ..183–184, 188 charging system warning and child safety seats ....185 light ..........12 description ......184, 188 jumping a disabled battery ..264 disposal ........191 maintenance-free ....294 driver air bag ....186, 189...
Page 337 Cruise control snow and ice ......234 (see Speed control) ....116 through water ....232, 236 Customer Assistance ....245 Dual automatic temperature Ford accessories for your control (DATC) ......86 vehicle ........286 Ford Extended Service Plan ..........273 Getting assistance outside Electronic message center ..127 the U.S.
Page 338 Index Engine ........327–328 Fuel ..........303 check engine/service engine calculating fuel soon light ........10 economy ......130, 307 cleaning ........282 cap ...........305 coolant ........297 capacity ........322 fail-safe coolant ......301 choosing the right fuel ...305 idle speed control ....294 comparisons with EPA fuel lubrication economy estimates ....310 specifications ....325, 327...
Page 339 Index GAWR (Gross Axle Weight Inspection/maintenance (I/M) testing ........311 Rating) ........236 calculating .......238 Instrument panel cleaning ........284 definition .........236 cluster ........10 driving with a heavy load ..236 lighting up panel and location ........236 interior ........96 GVWR (Gross Vehicle Weight Rating) ........236 calculating .......236, 238 Jack ..........259 definition .........236...
Page 340 Index Lights, warning and indicator ..10 heated ........114 AdvanceTrac ......12 programmable memory ..145, 158 air bag ........12 side view mirrors (power) ..115 anti-lock brakes (ABS) ..11, 211 Moon roof ........109 brake ..........11 charging system ......12 Motorcraft parts ....307, 322 check coolant ......13 cruise indicator ......13 door ajar ........13 engine oil pressure ....13...
Page 341 Index Power Windows ......112 warning light and chime ....12, 14, 178–179 Preparing to drive your Safety seats for children ..195 vehicle ........215 Seat belts (see Safety restraints) .....170 Seats ..........155 Radio ........19, 24 child safety seats ....195 Rear window defroster ....93 climate control ......159 memory seat ....145, 158 Relays ........249...
Page 342 Index checking the pressure ....318 Vehicle Identification Number replacing ........319 (VIN) ..........330 rotating ........318 Vehicle loading ......236 snow tires and chains ....321 tire grades .......317 Ventilating your vehicle ...209 treadwear ........317 Towing ........239 recreational towing ....244 trailer towing ......239 Warning chimes ......14 wrecker ........269 Warning lights (see Lights) ..10 Traction control...

Ford Expedition 2003 Owner's Manual

Introduction

Instrument Cluster

Entertainment Systems

Climate Controls

Lights

Driver Controls

Quick Links

Related Manuals for Ford Expedition 2003

Summary of Contents for Ford Expedition 2003

Table of Contents