Tascam 688 Midistudio Owner's Manual page 41

33 31,32
30 28
I 11111
i
I
. - SYNC ---. SCENE OATA
,en ...._ •
• I I ..----'
29
...
BB
-
~
-
1lUIl._
_ t-t
_
...
_HI
-, ...
If you've pressed TAPE In the right ASSIGN DUAL
column, you will be choosing tape as the source for a
dual channel (11-18), which can be used as an
additional monitoring position during tracking and
overdubbing.
If you've pressed TAPE In the left ASSIGN MAIN
column, you will be choosing tape as the source for a
main channel 11-8). This ·Is the route usually taken
during mixdown or bouncing tracks (see p. 13).
POST is usually used when you want the DUAL to act
as an effects sand, similar to the way the AUX l' and
AUX 2 pots work When you turn their
pots
to the right.
When POST is on, the DUAL pots lose their
independence; so Instead of thinking of them as
channels 11·20. they become"AUX 3-4" from the MAIN
channels 1-10, When you bring down fader 1, the
signal to the DUAL 11 pot will go down in proportion,
because It's getting its signal from a point aher the
main fader. See p. 29, "Dual as an Effect Send",
25. POST: This key has effect only on the lower half of
the INPUT page, since only the DUAL channels can be
put into POST mode. Press the POST key to enter POST
INPUT mode (and automatically leave ASSIGN, MUTE
or any other INPUT mode). While the POST Indicator Is
flashing. press any of the ten CHANNEL keys ('27) to
select the post-fadqr main signal as the source for the
DUAL control just above it. Pressing the CHANNEL key
again will turn the post selection off.
1 ,
J;
4 S 6 7
a s
10
OWMLllUn
0 0 0 0 0 0 0 0 0 0
BIiIl!IlI -~ 0
0 0 0 0 0 0 0 0 0
.....
~ O O D O D D D D D D
""
~ODDDDODDDO
IIIlIDII _ . 0 0 0 0 0
° °
0 0 0
-..,go
°
0 0 CJ O D D
°
0
" r : l O O O D D D D O D D
".,... llJr,lOOODDDDDDO
CIIlrsfDODODODDDD
26-........
-1---e
ASSIGN ASSIGN
MAlN DUAL
lAC MiG
ASSIGN MAl... OIlOUP 1 GAouP
~
DOD
t _ UNf
ASSIGN
EfF
GIlOUP 2 0R0lIP.
23_-+--..:.1===~1 ~ ~~
INPUT
24_+-~1==-+1=~~
Typically, you'll bring
8
LINE lnput to the main mix if it
needs EO, or it needs to be recorded onra multitrack.
Bring a line input to the dual mix If it's MIDI controlled
and you want to monitor it but not record it until
. mlxdown.
If you've pressed LINE in the left ASSIGN MAIN
column, you will be choosing LINE B as the source for a
main channel (1-10), sending it through the EO, insert
point. and Main Channel fader.
25
If you've pressed LINE In the right ASSIGN DUAL
column, you will be choosing LINE B as the source for a
dual channel (11-201. sending it to the DUAL lEVEL
control.
23. LINE: On the INPUT page of the display. press either
key to enter LINE INPUT mode (and automatically
leave MUTE or any other INPUT mode). While the LINE
indicator is flashing, press any of the ten CHANNEL
keys (#27) to select the line Jack as a source for that
channel. Pressing the CHANNEL key again will turn the
line selection off.
24. TAPE: On the INPUT page of the display. press either
key to enter TAPE INPUT mode (and automatically
leave ASSIGN. MUTE or any other INPUT mode). While
TAPE indicator is flashing, press any of the first eight
CHANNEL keys (#27) to select the output of the
multitrack tape as the input source for that channel.
Pressing the CHANNEL key again will turn the tape
selection off, Pressing CHANNEL keys 9-0 will have no
effect,
because there are only 8 tape tracks.
27
-40 -