NN-GD376S / NN-GD366M / NN-GD356W 2 DESCRIPTION OF OPERATING SEQUENCE 2.1. Variable power cooking 2.3. Inverter defrost, Auto menu & control Auto reheat High Voltage Inverter Power Supply (U) controls output power When the Auto Control feature is selected and the Start pad is by the signal from Digital Programmer Circuit (DPC).
NN-GD376S / NN-GD366M / NN-GD356W 3 CAUTIONS TO BE OBSERVED WHEN TROUBLESHOOTING Unlike many other appliances, the microwave oven is a high voltage, high current device. It is free from danger in ordinary use, though extreme care should be taken during repair.
NN-GD376S / NN-GD366M / NN-GD356W 3.3. Part replacement. 3.7. Sharp edges When any part or component is to be replaced, always ensure Caution that the power cord is removed from the wall outlet. Please use caution when unpacking, installing or moving 3.4.
NN-GD376S / NN-GD366M / NN-GD356W 4 DISASSEMBLY AND PARTS REPLACEMENT PROCEDURE 4.1. Magnetron 4.2. Digital programmer circuit (D.P.C) and membrane key 1. Discharge the high voltage capacitor. board. 2. Remove 1 screw holding air guide A on the magnetron. 3. Remove 1 screw holding reinforce bracket on the NOTE: magnetron.
NN-GD376S / NN-GD366M / NN-GD356W 4.3. Low voltage transformer To replace pop-up dial Remove pop-up dial from small D.P.C. board (DU) by and/or power relays (RY1, pulling it straight out. RY2) 6. Release 2 locking tabs on escutcheon base to remove big D.P.C.
NN-GD376S / NN-GD366M / NN-GD356W 4.5. Door assembly 4.6. Turntable motor 1. Remove door C from door E by carefully pulling outward, 1. Remove the motor cover by breaking off at the 4 spots starting from upper right hand corner using a flat blade indicated by arrows with a cutter or the like.
NN-GD376S / NN-GD366M / NN-GD356W 5 COMPONENT TEST PROCEDURE 5.3. Magnetron CAUTION NEW. H.V. 1. High voltage is present at the high voltage terminal of the High Voltage Inverter (U) including aluminum heat sink during any cook Continuity checks can only indicate an open filament or a cycle.
NN-GD376S / NN-GD366M / NN-GD356W 5.5. Inverter power supply (U) 5.6. Temperature thermistor DO NOT try to REPAIR H.V. Inverter power supply Those sensor monitors the heat produced by the heater circuit (U).Replace complete H.V. Inverter(U) Unit. and maintains the magnetron temperature which user had selected.
NN-GD376S / NN-GD366M / NN-GD356W 6 MEASUREMENTS AND ADJUSTMENTS 6.1. Adjustment of Primary latch 6.2. Measurement of microwave switch, Secondary latch output switch and Short switch. The output power of the magnetron can be determined by performing IEC standard test procedures. However, due to the 1.
NN-GD376S / NN-GD366M / NN-GD356W 7 TROUBLESHOOTING GUIDE DANGER HIGH VOLTAGES 1. DO NOT RE-ADJUST PRESET CONTROL on the H.V.Inverter (U). It is very dangerous to repair or adjust without proper test equipment because this circuit handles very large current and high voltage. Operating a misaligned inverter circuit is dangerous.
Page 17
NN-GD376S / NN-GD366M / NN-GD356W SYMPTOM CAUSE CORRECTIONS 1. Oven is dead. Open or loose lead wire harness Check fan motor if thermal cutout is defective. Open thermal cutout Fuse is OK. Open low voltage transformer No display and no operation at all.
NN-GD376S / NN-GD366M / NN-GD356W 7.3. Troubleshooting of inverter circuit (U) and magnetron NEW H.V. This oven is programmed with a self diagnostics failure code system which will help for troubleshooting. H95, H97, H98, and H99 are the provided failure codes to indicate magnetron and inverter circuit problem areas. This section explains failure codes of H95, H97, H98, and H99.
NN-GD376S / NN-GD366M / NN-GD356W 7.4. Simple way of H.V. Inverter/magnetron troubleshooting Purpose: Simple way (3/23 seconds rule) of identifying whether it’s Magnetron, Inverter, or others. Set-up: The unit under question is connected through the Ammeter as shown below. Procedure: Follow the matrix table below to identify the problem source.
NN-GD376S / NN-GD366M / NN-GD356W 8.2. PARTS LIST NOTE: 1. When ordering replacement part(s), please use part number(s) shown in this part list. Do not use description of the part. 2. Important safety notice: Components identified by mark have special characteristics important for safety.
NN-GD376S / NN-GD366M / NN-GD356W 8.3. DOOR ASSEMBLY Ref. No. Part No. Part Name & Description Pcs/Set Remarks F30188H00XP DOOR KEY A F30018H10SXP DOOR A GD366M F30018H10HXP DOOR A GD356W F302K8H00XP DOOR E(U) F30215G10XN DOOR KEY SPRING F30858H00XP DOOR C...