Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Avery Dennison Manuals
  4. Printer
  5. Monarch 9825
  6. Quick reference

Avery Dennison Monarch 9825 Quick Reference

Hide thumbs Also See for Monarch 9825:

Advertisement

Quick Links

Download this manual
â
Monarch
9825
®
Printer
TC9825QR Rev. AF 4/08
©2007 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.

Advertisement

loading

Related Manuals for Avery Dennison Monarch 9825

Summary of Contents for Avery Dennison Monarch 9825

  • Page 1 â Monarch 9825 ® Printer TC9825QR Rev. AF 4/08 ©2007 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.
  • Page 2 Any update will be incorporated in a later edition of this manual. ©2002 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved. No part of this publication may be reproduced, transmitted, stored in a retrieval system, or translated into any language in any form by any means, without the prior written permission of Paxar Corporation.
  • Page 3 This Quick Reference contains supply loading and general care and maintenance procedures. For more detailed information, refer to the Operator’s Handbook available on our Web site (www.monarch.com). For information about creating formats or programming the printer, refer to the Programmer’s Manual on our Web site. Note: Information in this document supercedes information in previous versions.
  • Page 4 U s i n g t h e C o n t r o l P a n e l The control panel has a two-line LCD display, 2 status lights, and five buttons. The control panel displays error codes/messages, and allows you to setup/configure the printer.
  • Page 5 L o a d i n g L a b e l s o r T a g s Open the cover. Unlock the printhead by turning the retaining latch. Lift printhead assembly using the printhead tab until the assembly locks into place.
  • Page 6 Lay the label strip across the supply guide so that a few inches extend past the front of the printer. Tuck the supply under the nibs and in between the die cut sensor. For fan-fold supplies, lay the label strip over the supply holder and across the supply guide so that a few inches extend past the front of the printer.
  • Page 7 Loading Labels for the Optional Peel Mode Peel mode must be purchased separately. In peel mode, the printer separates the backing paper from the label. The next label is not printed until the completed one is removed from the printer. Make sure the printer is configured for on-demand mode and the correct supply type.
  • Page 8 When removing the backing paper, pull up across the saw-toothed tear edge. Make sure the backing paper tears at the edge. Close the printer's cover. Press Feed/Cut to position the supply under the printhead. To load and use linerless supplies, refer to the Operator’s Handbook. A d j u s t i n g t h e W i d e / N a r r o w K n o b s You may need to adjust the two wide/narrow knobs according to the width of your supply.
  • Page 9 L o a d i n g R i b b o n Open the cover. Unlock the printhead by turning the retaining latch. Lift printhead assembly using the Deflector Tab printhead tab until the assembly locks into place. Push the deflector tab down. Slide the extra ribbon core on the take- up reel as far as it will go with the "This End Out"...

  • Page 10: Print Mode

    P r i n t i n g Before you print, make sure the printer is connected and ready to receive data. Turn on the printer. Your printer is ready to receive and print batches when you see PRINT MODE Ready Download a format and a batch.
  • Page 11 C l e a r i n g J a m s When you are printing and a jam occurs, the Fault light on the printer's front panel blinks. Turn off the printer and open the cover and printhead assembly. If necessary, remove the label roll and ribbon.
  • Page 12 Clean the platen roller with a cloth dampened with water. However, if Platen there is adhesive gum build-up on Roller the platen roller, moisten a cotton swab with isopropyl alcohol. Turn the platen roller with your finger and run the cotton swab or cloth across it.
  • Page 13 T r o u b l e s h o o t i n g This section lists common problems and their solutions. Problem Action Error message appears Turn off the printer, wait fifteen seconds during startup and then turn on the printer. Call Technical Support if the error message reappears.
  • Page 14 C o m m o n E r r o r s Error Description/Action Name must be 1 to 8 characters inside quotes. Supply width is invalid. Code page selection defined in the field is invalid. Data length is too long. Format referenced by batch not in memory.
  • Page 15 Printer has not sensed a supply mark when expected or is out of supplies. Press Escape/Clear and try to continue printing. Change supply. Printer did not sense a black mark when expected. Press Escape/Clear and try to continue printing. Change supply. Printer sensed a mark in the wrong place.