Summary of Contents for Briggs & Stratton Prestige 1800 Series
Page 1
Print Vendor How to use this file Operator’s Manuals Instructions Paper Size: • 11x17 • Body - 50 lbs brilliant white offset or equivalent • Cover - on pre-printed two tone “Swash” stock. Press: • Body - 1 color, 2-sided •...
Page 2
THIS PAGE INTENTIONALLY BLANK (FOR PLACEMENT ONLY - DO NOT PRINT)
Safety Rules & Information Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Remember, you are responsible for your safety and that of those around you.
Safety Rules and Information Slope Operation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don’t have adequate traction can cause you to lose control or roll over.
Safety Rules & Information Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects.
Page 9
Safety Rules and Information SLOPE OPERATION WARNING Slopes are a major factor related to loss-of-control and tip- Never operate on slopes greater than 17.6 percent over accidents, which can result in severe injury or death. (10°) which is a rise of 3-1/2 feet (106 cm) vertically in Operation on all slopes requires extra caution.
Page 10
Safety Rules & Information SERVICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other 13. If the fuel tank must be drained, it should be drained sources of ignition. outdoors. 2. Use only approved gasoline containers. 14.
Identification Numbers Identification Numbers Product Identification Tag North American / Model / Modéle / Model xxxxxxxx CE Models Serial / Sèrie / Serie xxxxxxxxxx Briggs & Stratton Power Products Group, L.L.C. Milwaukee, WI 53201 USA Tractor ID Tag Part No. xxxxxxx CE Models xxxxxxxxxxxxxxx PRODUCT...
Safety Decals Safety Decals All DANGER, WARNING, CAUTION and instructional messages on your rider and mower should be carefully This unit has been designed and manufactured to pro- read and obeyed. Personal bodily injury can result when vide you with the safety and reliability you would expect these instructions are not followed.
Safety Icons Safety Icons Danger: Machine Rollover. Warning: Read Operator’s Manual. Do not use this machine on slopes Read and understand the greater than 10°. Operator’s Manual before using this machine. Danger: Dismemberment. Danger: Thrown Objects. This machine can amputate limbs. This machine is capable of throwing Keep bystanders and children away objects and debris.
Features & Controls Electric Hydraulic HOC Models Lift Models Manual Lift Models Manual Manual HOC Models HOC Models Figure 1. Controls Control Functions The information below briefly describes the function of individual controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.
Features & Controls Manual Lift Models: The cutting height adjustment knob controls the mower cutting height. PTO Switch The PTO (Power Take-Off) switch engages and disen- Cruise Control (Select Models) gages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. The cruise control is used to lock the ground speed con- Note that the operator must be seated firmly in the trac- trol in forward.
Features & Controls Manual Lift Models: The attachment lift control lever raises and lowers attachments that utilize the tractor’s Attachment Lift Control Lever manual lift linkage. To lower an attachment: pull the When using the mower deck, lift the deck off the ground lever back slightly, depress the release button, and push while transporting to and from the job site.
Features & Controls Dashboard Display & Functions Display Items Refer to Figure 3. A. FUEL LEVEL Indicates the amount of fuel in the fuel tank. Left is empty; right is full. B. HOUR METER / CLOCK / SERVICE INDICATOR Cruise Displays the clock, hour meter, and maintenance reminder.
Operating the Tractor General Operating Safety Safety Interlock System Be sure to read all information in the Safety and Tests Operation sections before attempting to operate this unit. Become familiar with all of the controls and how to stop This unit is equipped with safety interlock switches and the unit.
Operating the Tractor Starting the Engine Stopping the Tractor & Engine 1. While sitting in the operator’s seat, fully depress the 1. Return the ground speed control(s) to neutral. brake pedal or set the parking brake. 2. Disengage the PTO and wait for all moving parts to 2.
Operating the Tractor Mowing Attachment Operation in Reverse 1. Set the mower cutting height to the desired level and If an operator chooses to operate a PTO driven attach- set the gauge wheels to the appropriate position (if ment in reverse, the RMO system can be used. To use equipped).
Operating the Tractor Pushing the Tractor by Hand 1. Disengage the PTO and turn the engine off. 2. Pull the transmission release (B, Figure 4) back approximately 2-1/2” (6 cm) to lock into released position. 3. The tractor can now be pushed by hand. DO NOT TOW TRACTOR Towing the unit will cause transmission dam- age.
Operating the Tractor Mower Deck Removal & Installation 44” Simplicity, Massey Ferguson or AGCO Models WARNING Figure 6. Lift Arms Engage parking brake, disengage PTO, stop (Viewed from underneath right side of tractor) engine and remove key before attempting to A.
Page 23
Operating the Tractor Mower Deck Removal & Installation 44” Snapper Models WARNING Engage parking brake, disengage PTO, stop Figure 9. Lift Arms engine and remove key before attempting to (Viewed from underneath left side of tractor) install or remove the mower. A.
Page 24
Operating the Tractor Mower Deck Removal & Installation Simplicity, Massey Ferguson and AGCO Models Figure 11. Pivoting Gauge Wheels - Select Models WARNING Engage parking brake, disengage PTO, stop engine and remove key before attempting to install or remove the mower. Muffler and surrounding areas may be hot.
Operating the Tractor Installing the Mower Deck NOTE: Perform mower installation on a hard, level sur- face such as a concrete floor. 1. Park the tractor, fully lower the attachment lift, turn off the PTO switch, turn off the engine, remove the key, and engage the parking brake.
Operating the Tractor Attaching a Trailer The maximum horizontal drawbar force allowed is 444 Newton. The maximum vertical drawbar force is 222 Newton. This equates to a 396 lbs (180 kg) trailer on a 10 degree hill. Secure the trailer with an appropriately sized clevis pin (A, Figure 16) and clip (B).
Lawn Care & Mowing Information How and When to Water, HOW TO WATER YOUR LAWN The best method of watering a lawn Fertilize & Aerate is to imitate a slow, soaking rain, Most lawns are watered too often, applying about 1 inch of water. but with too little water.
Lawn Care & Mowing Information When and How Often to Mow The time of day and condition of the grass greatly affect the results you’ll get when mowing. For the best results, follow these guidelines: ● Mow when the grass is between 3”-4” (7,5-10 cm) high. ●...
Regular Maintenance MAINTENANCE SCHEDULE & PROCEDURES The following schedule should be followed for normal care of your tractor and mower. Before Every 5 Every 25 Every Every Spring & SAFETY ITEMS Each Hours Hours Fall Hours Hours • Check Safety Interlock System •...
Regular Maintenance Check / Clean Oil Cooler (Select Models) SERVICE INTERVAL: EVERY 25 HOURS, OR AS NECESSARY The engine oil cooler is located on the side of the engine (A, Figure 19) and should be cleaned with compressed air at regular intervals or if dirty. Safety Interlock System Check SERVICE INTERVAL: EVERY FALL &...
Regular Maintenance Check Tire Pressures SERVICE INTERVAL: EVERY 25 HOURS Tire Pressure should be checked periodically, and main- tained at the levels shown in the chart. Note that these pressures may differ slightly from the “Max Inflation” stamped on the side-wall of the tires. The pressures shown provide proper traction, improve cut quality, and extend tire life.
Regular Maintenance Lubrication SERVICE INTERVAL: EVERY 25 HOURS Lubricate the unit at the locations shown in Figures 22- 25 as well as the lubrication points listed. Generally, all moving metal parts should be oiled where contact is made with other parts. Keep oil and grease off belts and pulleys.
Regular Maintenance Lubricate Rear Axle Shafts Prestige / 2800 / 1800 / 500 / GT SERVICE INTERVAL: YEARLY We recommend removing the rear wheel hubs and lubri- cating the axle shafts yearly. This prevents the wheel hubs from seizing onto the axle shaft and makes future service easier.
Regular Maintenance WARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. WARNING For your personal safety, blade mounting capscrews must each be installed with a LOOSEN hex/spline washer and spring washer, then securely tightened.
Regular Maintenance Transmission Identification Several service procedures within this book are identified by, and vary by, transmission type. To determine what transmission is in your tractor, check the identification tag attached to the axle of the transmission (Figure 31a), or check your tractor’s parts book. Figure 30.
Page 38
Regular Maintenance Figure 32. Seat Deck Access Plug A. Expansion Chamber Access Plug Figure 33. Differential Fill Plug Access K71 Maintenance A. Differential Fill Plug The following maintenance procedures must be per- formed on the K71 transmission after the first 50 hours of operation and then after every 250 hours.
Page 39
Regular Maintenance Figure 36. Internal Transmission Filter Service A. Filter Access Cap B. Internal Filter Figure 37. Transmission Drain Plugs A. 14mm Drain Plugs B. Filter Access Cap 5. Remove and replace the internal transmission filter (B, Figure 36). 6. Reinstall the filter access cap (A, Figure 36) and the two 14mm drain plugs (A, Figure 37).
Troubleshooting, Adjustment, & Service Troubleshooting WARNING While normal care and regular maintenance will extend To avoid serious injury, perform maintenance on the life of your equipment, prolonged or constant use the tractor or mower only when the engine is may eventually require that service be performed to stopped and the parking brake engaged.
Troubleshooting, Adjustment, & Service Tractor Troubleshooting Cont. Tractor drive belt slips. 1. Clutch/brake is out of adjustment. See Adjustments Section. 2. Pulleys or belt greasy or oily. Clean as required. 3. Belt stretched or worn. Replace with new belt. 4. Idler pulley pivot bracket Remove idler pulley bracket, clean and lubricate.
Troubleshooting, Adjustment, & Service Battery Charging WARNING Keep open flames and sparks away from the battery; the gasses coming from it are highly explosive. Ventilate the battery well during charging. A dead battery or one too weak to start the engine may be the result of a defect in the charging system or other electrical component.
Troubleshooting, Adjustment, & Service Steering Wheel Adjustment NOTE: The steering wheel on Snapper models is not adjustable. 1. Use a suitable punch to remove the roll pin at the base of the steering wheel (B, Figure 41). 2. Pull down on the rubber boot to expose the two holes in the steering shaft (A).
Troubleshooting, Adjustment, & Service PTO clutch adjustment WARNING To avoid serious injury, perform adjustments only with engine stopped, key removed and tractor on level ground. Check the PTO clutch adjustment after every 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed.
Troubleshooting, Adjustment, & Service Gauge Wheels (Select Models) The mower gauge wheels can be placed in several posi- tions depending on the height of cut. When using higher cutting heights, set the wheels in the lower position. When using lower cutting heights, set the wheels in the upper position.
Troubleshooting, Adjustment, & Service Leveling The Mower If the cut is uneven, the mower may need leveling. Unequal or improper tire pressure may also cause an uneven cut. Make sure tire pressure is correct as speci- fied in Checking Tire Pressure. SIDE-TO-SIDE LEVELING 1.
Troubleshooting, Adjustment, & Service Mower Belt Replacement 1/8” Gap To avoid damaging belts, DO NOT PRY BELTS OVER PULLEYS. 44” & 50” PTO Belt Replacement 1. Park the tractor on a smooth, level surface such as a concrete floor. Disengage the PTO, turn off the engine and lock the parking brake.
Troubleshooting, Adjustment, & Service Figure 55. Mower Deck - 44" & 50” Mowers Figure 56. Mower Deck - 54” Mowers A. Capscrew A. Taptite Screws B. Right-hand Arbor Cover B. Right-hand Arbor Cover C. Spring C. Spring D. Left-hand Arbor Cover D.
Specifications NOTE: Specifications are correct at time of printing and are subject to change without notice. * The gross power rating for individual gas engine models is labeled in accordance with SAE (Society of Automotive Engineers) code J1940 (Small Engine Power & Torque Rating Procedure), and rating performance has been obtained and corrected in accor- dance with SAE J1995 (Revision 2002-05).
Parts & Accessories Replacement Parts Technical Manuals Additional copies of this manual are available, as well as Replacement parts are available from your authorized dealer. Always use genuine Simplicity Service Parts. fully illustrated parts lists. These manuals show all of the product’s components in exploded views (3D illustrations which show the relationship of parts and how they go Maintenance Items...