Related Manuals for Jensen VM9512
Summary of Contents for Jensen VM9512
- Page 1 VM9512 Installation and Operation Manual Multimedia Receiver BAND Press Audio VM9512 ® video CLOSE DISP ANGLE / TILT PICTURE Enter Watts Peak Watts en Crête Vatios el Máximo 60W x 4...
-
Page 3: Table Of Contents
CONTENTS Thank you for choosing a Jensen product. We hope you will find the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all the features of your new Jensen VM9512 Mobile Multimedia Receiver for maximum enjoyment. -
Page 5: Preparation
VM9512 PREPARATION Congratulations on your purchase of the Jensen VM9512 Mobile Multimedia Receiver. It’s a good idea to read all of the instructions before beginning the installation. We recommend having your Jensen VM9512 installed by a reputable installation shop. Features •... -
Page 6: Disconnecting Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. NOTE: If the VM9512 is to be installed in a car equipped with an on-board drive or navigation computer, do not disconnect the battery cable. -
Page 7: Wiring Diagram
VM9512 WIRING DIAGRAM See the MediaLink and Satellite Connections diagram for more information about connecting a satellite receiver and an iPod (through the MediaLink). External Power Amplifier Antenna Jack Antenna Car Phone FRONT L+ FRONT L- FRONT R+ FRONT R-... -
Page 8: Medialink/Satellite Connections
SAT Radio SAT L SAT R *SAT Cable Kit: JXMC or XMDJEN100 (sold separately) **XM or Sirius satellite tuner (sold separately) MediaLink 3.5mm - Audio VIDEO LEFT RIGHT iPod Video iPod jLink iPod Cable (Included) VM9512 iPod Mini iPod Nano... -
Page 9: Installation
NOTE: When replacing a fuse, be sure to use correct type and amperage to avoid damaging the radio. The VM9512 uses one 10 amp mini-ATM fuse, located in the black filter box in-line with the main wire harness. Final Installation After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). -
Page 10: Anti-Theft Feature
ANTI-THEFT FEATURE The VM9512 is equipped with an anti-theft feature requiring the user to enter a password upon initial power on. The default user password is 012345 (6 digits). To change the anti-theft and RATINGS protection password, perform the following steps:... -
Page 11: Controls And Indicators
Press to silence the receiver. Press again to resume previous volume level. BT Mode: Answer Bluetooth call. NOTE: The VM9512 features Softmute, which will allow the volume to increase or decrease gradually when the MUTE function is activated or deactivated. - Page 12 Multimedia Receiver BAND Pres s Audio VM9512 VM9512 DISP CLOSE PICTURE ANGLE / TILT Enter...
-
Page 13: Remote Control
VM9512 REMOTE CONTROL The VM9512 Remote controls both the front and rear zones. To switch from front to rear zone, move the F/R switch (32) located on the right side of the controller. NOTE: Your remote control may differ slightly from the one pictured here. - Page 14 Stops playback Enters Direct Access mode Enters Direct Access mode Fast reverses the disc content VM9512 SATELLITE iPod Displays diagnostics screen Displays iPod menu Category list in CG mode Toggles on/off audio output Toggles on/off audio output...
- Page 15 VM9512 Button Name Ref# ||>/BAND Slow Forward/Slow Reverse Play/pause X2, X4, X8 Displays Brightness/Contrast Displays Brightness/Contrast Controls Controls OPEN/ Opens/closes the TFT monitor Opens/closes the TFT monitor CLOSE Decreases monitor tilt angle Decreases monitor tilt angle TILT Increases monitor tilt angle...
-
Page 16: Using The Tft Monitor
CAMERA mode upon reverse driving. When the reverse driving stops, the monitor returns to its original input mode. VM9512 Aspect Ratio Press the WIDE button (28) on the remote control or WIDE button (22) on the monitor to adjust the aspect ratio as... - Page 17 VM9512 Parameter Adjustment Procedure Enter Picture Quality Setting Mode: Press the PIC button (24) on the remote control or press and hold the WIDE/PICTURE button (22) on the moni- tor. Select Item to Set: Use the up/down joystick buttons to select “BRIGHT” or “CONTRAST”.
-
Page 18: Operating Instructions
Press the joystick ENTER button on the control panel (13) or remote control (18) to select the highlighted option. Use the joystick to adjust the selected feature to the desired setting. VM9512 Table 4: Audio Adjustments Function Adjustment Options User... - Page 19 VM9512 • PIP: Touch to view the Rear Zone, current Front Zone, or NAV screen. Use the left/right arrows below the PIP image to change the PIP source. PIP: DISC 01:02 AM (Root) DISC 4/84 00:00:23 Cherry Poppin Da Chris Isaak - Baby...
-
Page 20: Multi-Zone Operation
MULTI-ZONE OPERATION Independent sources can be played simultaneously on the VM9512. For example, a video game console can be seen on the front screen while DVD video is available to rear passengers. Connecting the Rear Zone Touch Screen You can connect up to two additional monitors (sold separately) for rear passengers, one of which can be a Touch Screen. -
Page 21: Setup Menu
VM9512 SETUP MENU To access system settings, press the SETUP button (31) on the remote control or touch the button on the screen to enter the “SETUP” menu. The “GENERAL” sub-menu appears highlighted in blue. 02:40 SETUP RADIO RADIO General... - Page 22 By default, the rating system is set at the highest setting (with no restrictions). The parental lock is released VM9512 only by entering the correct password. Once the password is entered, rating is available for setup.
- Page 23 VM9512 Setting Options Function Camera In Normal Mirror Reverse the camera image as if looking through a rear-view mirror. TFT Auto Auto The TFT panel automatically opens Open when the unit is turned on. Manual When the ignition is turned OFF, the...
-
Page 24: Tuner Operation
Move the joystick to the right. To seek the next lower station: • Touch the |<<| button on screen. • Move the joystick to the left. VM9512 Manual Tuning To increase or decrease the tuning frequency one step: • Touch the buttons on screen. - Page 25 VM9512 close the menu). The preset number and station appears highlighted. Recalling a Station Select a band (if needed). Touch an on-screen preset button (6) to select the corresponding stored station. 87.5 90.1 98.1 106.1 107.9 102.9 Auto Store (AS)
-
Page 26: Satellite Radio Operation
Mem: P1 P2 P3 P4 P5 P6 E x i t VM9512 Touch the preset number in which you would like to store the current station (or press EXIT to cancel and close the menu). The preset number and station appears highlighted. - Page 27 VM9512 01:02 SAT1 CH001 XM Preview Preview ######## 001 XM Preview 004 The 40s 005 The 50s 006 The 60s 007 The 70s DIAG Title: www.xmradio.com • While in Search Mode, to switch between Channel and Category search modes, press the CH or CAT buttons on the touch screen.
-
Page 28: Dvd/Vcd Video Operation
Keep pressing and releasing the button to increase the slow forward rate from “2X” to “4X” and “8X” and then begin slow reverse. VM9512 Repeat Playback Press the RPT button (19) on the control panel, the RPT button (7) on the remote control, or the... - Page 29 VM9512 Press the TITLE button (2) on the remote control or on screen to select a different title for playback. Press the ENTER (joystick) button to confirm your selection and begin playback. You can also select a title using the touch screen.
- Page 30 Region 4: Australia, New Zealand, Middle and South America, South Pacific Ocean Islands/ Oceania • Region 5: Russia, Mongolia, India, Middle Asia, Eastern Europe, North Korea, North Africa, North-West Asia • Region 6: Mainland China • ALL: All regions VM9512...
-
Page 31: Dvd/Cd Audio Operation
Instructions for TFT control and Insert/Eject are the same for DVD and CD operation. Please see the DVD/Disc Video Operation section for information about these topics. The VM9512 will play music or other audio files from the following disc media: •... - Page 32 TRACK: _ _ / ## Exit Clear Enter the desired track number using the on-screen number pad, and then press the Enter button. To exit the screen without making a selection, touch Exit. To clear your entry and start over, touch Clear. VM9512...
-
Page 33: Mp3/Wma/Ipod Operation
Folder Search, File Search or Folder Select, as shown below. The VM9512 player will only recognize three folder levels and does not display folders containing only other folders. In the example above, the unit will display folders 3, 4, 6, and 8, but not 2 and 7 since they do not contain any tracks directly. - Page 34 RPT button (7) on the remote control to alter repeat mode according to the following: Repeat Single, Folder Repeat, Repeat Off. VM9512 Random Play Select Press the RDM button (33) on the remote control to play the files on the disc in a random, shuffled order.
- Page 35 SUB-TITLE button (9) on the remote control to access the iPod PHOTO mode. The VM9512 will release control back to the iPod so you can select video media to be displayed on the TFT monitor. To exit PHOTO mode, touch the screen.
-
Page 36: Bluetooth User Interface
Adhere to the following guidelines for successful operation. • Before using Bluetooth functions, you must pair your mobile phone to the VM9512 head unit (see “Pairing the Bluetooth System with Your Mobile Phone and Head Unit”). To ensure the best reception for pairing and reconnection, please make sure the phone battery is fully charged before you begin. -
Page 37: Call Transfer
Pairing Code field under the Bluetooth SETUP menu. The default pairing code for many phones is “0000”. The default code for the VM9512 is “1234”. See “Bluetooth Sub-menu Features” on page 18 for instructions on entering the pairing code. -
Page 38: Bluetooth Setup
Touch the area to the right of “Connect” to select “Auto”. Advanced Audio Distribution Profile (A2DP) The VM9512 allows you to play back audio files from your phone, PDA or personal music player using a Bluetooth connection. Before using an audio player, it may be necessary to enter a PIN code into the unit. -
Page 39: Troubleshooting
VM9512 TROUBLESHOOTING Problem GENERAL Unit will not power on Radio Fuse blown Car battery fuse blown Illegal operation Remote control does not function Battery depleted Battery installed incorrectly No/low audio output Improper audio output connection Volume set too low Improper “MUTE” connection... -
Page 40: Error Messages
Cause Clean disc with soft cloth Insert disc with label side up Insert disc Clean disc with soft cloth Insert disc with label side up Press EJECT key for 5 seconds to reset loading mechanism VM9512 Corrective Action Corrective Action... - Page 41 VM9512 Care and Maintenance Use only a clean silicone cloth and neutral detergent to clean the front panel or monitor. A rough cloth and non- neutral detergent (such as alcohol) may result in scratching or discoloration. Do not get water or cleaning fluids on the unit.
-
Page 42: Specifications
Power Output: 18 Watts RMS x 4 channels into 4-Ohms @ < 1% THD+N Signal to Noise Ratio: 70dBA below reference (Reference: 1 Watt, 4-Ohms) Frequency Response: 20 Hz - 20 kHz, -3dB. (Aux Input used as reference input) Reference Supply Voltage: 14.4VDC *Specifications subject to change without notice. VM9512... -
Page 43: Limited Warranty
Limited Warranty CD or Multimedia Radios/Headunits Audiovox Electronics Corporation (“the Company”) is committed to quality and customer service, and are pleased to offer you this Warranty. Please read it thoroughly and contact the Company at 1-800- 323-4815 with any questions. Who is covered? The Company extends this warranty to the original retail purchaser of products purchased through an authorized Audiovox retailer in the U.S.A., Puerto Rico or... - Page 44 Audiovox Electronics Corporation Hauppauge, NY 11788 Technical Assistance: 1-800-323-4815 www.jensen.com © 2007 Audiovox Ver. 070607 Printed in China...