Harman Kardon AVR 140 Owner's Manual page 39

Programming the Remote
3. Press either the AVR Selector
Input Selector , depending on which
system's volume control you wish to have attached
for the punch-through mode. The Program
Indicator will blink green three times and
then go out to confirm the data entry.
Example: To have the AVR's volume control acti-
vated even though the remote is set to control
the TV, first press the Video/TV Input Selector
and the Mute button at the same time.
Next, press the Volume Up button
by the AVR Input Selector .
NOTE: Should you wish to return the remote to
the original configuration after entering a Volume
Punch-Through, you will need to repeat the steps
shown above. However, press the same Input
Selector in steps one and three.
Channel Control Punch-Through
The AVR's remote may be programmed to operate
so that the channel control function, performed
with the Sleep and Surround
for either the TV, cable or satellite receiver used in
your system may be used in conjunction with one
of the other devices controlled by the remote. For
example, while using and controlling the VCR,
you may wish to change channels on a cable box
or satellite receiver without having to change the
device selected by the AVR or the remote. To pro-
gram the remote for Channel Control Punch-
Through, follow these steps:
1. Press the Input Selector button
device you wish to have the channel control
associated with and the Mute button
same time until the red light illuminates under the
Input Selector and the Program
Indicator flashes amber.
2. Press the Volume Down button
Program Indicator will stop flashing and
stay amber.
3. Press and release the AVR or Input
Selector button for the device that will be
used to change the channels. The Program
Indicator will blink green three times and
then go out to confirm the data entry.
Example: To control the channels using your TV
while the remote is set to control the VCR, first
press the VID 1/VCR Input Selector button
and the Mute button at the same time. Next,
release them and press the Volume Down button
, followed by the same Input Selector button
.
NOTE: To remove the Channel Control Punch-
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
above. However, press the same Input Selector
in Steps 1 and 3.
or the Transport Control Punch-Through
The AVR's remote may be programmed to operate
so that the Transport Control Functions
(Play, Stop, Fast Forward, Rewind, Pause and
Record) for a VCR, DVD or CD will operate in con-
junction with one of the other devices controlled
by the remote. For example, while using and con-
trolling the TV, you may wish to start or stop your
VCR or DVD without having to change the device
selected by the AVR or the remote. To program the
, followed
remote for Transport Control Punch-Through, fol-
low these steps:
1. Press the Input Selector
you wish to have the channel control associated
with and the Mute button
until the red light illuminates, under the Input
Selector and the Program Indicator
flashes amber.
2. Press the Play button
Indicator will stop flashing and stay amber.
3. Press and release the AVR
Selector button
buttons,
used to change the channels. The Program
Indicator will blink green three times and
then go out to confirm the data entry.
Example: To control the transport of a CD player
while the remote is set to control the TV, press the
VID 2/TV Input Selector button
Mute button at the same time. Next, release
them and press the Play button
the CD Input Selector button
NOTE: To remove the Channel Control Punch-
for the
Through and return the remote to its original con-
figuration, repeat the steps shown in the example
at the
above. However, press the same Input Selector
in Steps 1 and 3.
NOTE: Before programming the remote for
Volume, Channel or Transport Punch-Through,
. The
make certain that any programming needed for the
specific TV, CD, DVD, Cable or Satellite Receivers
has been completed.
Resetting the Remote Memory
As you add components to your home-theater
system, occasionally you may wish to totally repro-
gram the remote control without the confusion of
any commands, macros or "Punch-Through"
programming that you may have done. To do this,
it is possible to reset the remote to the original fac-
tory defaults and command codes by following
these steps. Note, however, that once the remote is
reset, all commands or codes that you have
entered will be erased and will need to be re-
entered:
for the device 1. Press any of the Input Selector buttons
and the "O" button
at the same time the Program Indicator
amber.
2. Press the "3" button
3. The red LED under the Input Selector
. The Program
go out and the Program Indicator
flashing and turn green.
or Input
4. The Program Indicator
for the device that will be
until the remote is reset. Note that this may take a
while, depending on how many commands are in
the memory and need to be erased.
5. When the Program Indicator
the remote has been reset to the factory settings.
and the
, followed by
.
at the same time until
begins to flash
three times.
will
will stop
will remain green
goes out,
PROGRAMMING THE REMOTE 39