Troubleshooting; Specifications - Sony AIR-SA10 Operating Instructions

Troubleshooting
Make sure the power cord is correctly and firmly
connected.
2
Find your problem in the checklist below, and take
the indicated corrective action.
If the issue persists, contact your nearest Sony dealer.
When bringing this unit in for repairs, be sure to
bring in the entire system (this unit. the S-AIR main
unit, and wireless transceivers).
This product is a system product, and the entire
system is needed to determine the location requiring
repair.
If the STANDBY indicator flashes
Immediately unplug the power cord, and check the
following item.
• Is anything blocking the ventilation holes on the rear
of the unit?
After the STANDBY indicator
I1J
stops flashing,
reconnect the power cord, and turn on the unit. If the
issue persists. contact your nearest Sony dealer.
connecting the unit and S-AIR main unit is not
possible. (The S-AIR indicator
I1ID
flashes.)
• If you use another S-AIR main unit, place it more than
8 m (26
'I.
feet) away from the S-AIR main unit you
are using.
• Confirm the S-AIR IDs of the unit and the S-AIR
main unit.
-The
unit is paired with another S-AIR main unit. Pair
the unit with the desired S-AIR main unit.
·'lbe unit is paired with another S-AIR main unit.
Cancel pairing.
• Place so that the unit and the S-AIR main unit are
separated from other wireless devices.
• Stop using any other wireless devices.
• "me S-AIR main unit is turned ofF. Make sure the AC
power cord (mains lead) is connected and turn on the
S-AIR main unit.
There is no sound.
·'fyou use another S-AIR main unit, place it more than
8 m (26
1/ 4
feet) away from the S-AIR main unit you
are using.
• Confirm the S-AIR IDs of the unit and the S-AIR
main unit.
• Check the pairing setting.
• Place so that the unit and the S-AIR main unit are
closer.
• Stop using any equipment that generates
electromagnetic energy such as a microwave oven.
• Place so that the unit and the S-AIR main unit are
separated from other wireless devices.
• Stop using any other wireless devices.
• Change the S-AIR ID settings of the unit and the S-
Al R main unit.
··I'urn off the unit and S-AIR main unit and then turn
them on again.
• Check that the power cord is connected securely and
the unit is turned on.
• Check that headphones are not connected to the
r::
(headphone) jack on the rear of the unit.
• [ncrease the volume of the unit.
There is noise or the sound skips.
·11' you usc another S-AIR main unit, place it more than
8 m (26
1/. 1
feet) away from the S-AIR main unit you
are using.
• Place so that the unit and the S-AIR main unit are
closer.
• Stop using any equipment that generates
electromagnetic energy such as a microwave oven.
• Place so that the unit and the S-AIR main unit are
separated from other wireless devices.
• Stop using any other wireless devices.
• Change the S-AIR ID settings of the unit and the
s-
Al R main unit.
• Do not place a mobile phone near the unit, as this may
result in noise.
To reset the unit to factory settings
If the unit still does not operate properly, reset the unit
to factory settings.
Disconnect and reconnect the power cord, and
then turn on the unit.
Press.
[1],
DISPLAY
[ID
and
lit! IT]
at the same
time.
All user-configured settings, such as timer, clock, etc.
are deleted.
Messages
CANCEL: Time out without pairing.
COMPLETE: Pairing is completed.
10 A: Sets the S-AIR ID to "A:'
10 B : Sets the S-AIR ID to "8."
10 C: Sets the S-AIR ID to
"c:'
LINKED: The unit is connected to the S-AIR main unit.
PAIRING: Pairing is in progress.
S-AIR : Displayed from the point power of the unit is
turned on until connection with the S-AIR main unit
is established.
TIME NG : The Play Timer start and end times are set to
the same time.
UNLINKED: Displayed when the connection with the
S-AIR main unit is cut off.
Specifications
Amplifier section
U.S.A. model:
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 3 ohm loads, both channels driven, from
300 - 20,000Hz; rated 4 watts per channel minimum
RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
Other models:
Continuous RMS power output (reference):
4
+
4 W (3 ohms at 1 kHz, 10% THD)
Output
':: (stereo mini jack): Accepts headphones with an
impedance of 8 ohms or more
Speaker section
Speaker system: Full range, bass-reflex type
Speaker units: 65 mm, cone type (2)
Nominal impedance: 3 ohms
Wireless transceiver (EZW-RTl 0)
Communication System: S-AIR Specification version 1.0
Output: 12.0 mW
Frequency band: 2.4000 GHz - 2.4835 GHz
Modulation method: DSSS
Power requirements: DC 3.3 V, 350 mA
Dimensions (w/h/d): 50 mm
x
13 mm
x
60 mm
(2 x 171.~2 x 2
3/ x
in)
Mass: 24 g (I oz)
General
Power requirements:
North American model: 120
V
AC, 60 Hz
Oceanian model: 230 - 240 V AC, 50/60 Hz
Power consumption: 15 W
Dimensions (w/h/d): Approx. 300 x 136 x 115 mm
(I
1 7 1, x 5 'I, x 4 'I, in)
Mass: Approx. 2.2 kg (41b 14 oz)
Supplied accessories: Wireless transceiver EZW-RTIO
(I)
Design and specifications are subject to change without
notice.
• Standby power consumption: 1.0 W
• Halogenated flame retardants are not
used in the certain printed wiring
boards.
• Halogenated flame retardants are n.ot
used in cabinets (Except for the U.S.A.
model).
Troubleshooting
Make sure the power cord is correctly and firmly
connected.
2
Find your problem in the checklist below, and take
the indicated corrective action.
If the issue persists, contact your nearest Sony dealer.
When bringing this unit in for repairs, be sure to
bring in the entire system (this unit. the S-AIR main
unit, and wireless transceivers).
This product is a system product, and the entire
system is needed to determine the location requiring
repair.
If the STANDBY indicator flashes
Immediately unplug the power cord, and check the
following item.
• Is anything blocking the ventilation holes on the rear
of the unit?
After the STANDBY indicator
I1J
stops flashing,
reconnect the power cord, and turn on the unit. If the
issue persists, contact your nearest Sony dealer.
Connecting the unit and S-AIR main unit is not
possible. (The S-AIR indicator
I1ID
flashes.)
• If you use another S-AIR main unit, place it more than
8 m (26
'I.
feet) away from the S-AIR main unit you
are using.
• Confirm the S-AIR IDs of the unit and the S-AIR
main unit.
-The unit is paired with another S-AIR main unit. Pair
the unit with the desired S-AIR main unit.
·'lbe unit is paired with another S-AIR main unit.
Cancel pairing.
• Place so that the unit and the S-AIR main unit are
separated from other wireless devices.
• Stop using any other wireless devices.
• "me S-AIR main unit is turned ofF. Make sure the AC
power cord (mains lead) is connected and turn on the
S-AIR main unit.
There is no sound.
·'fyou use another S-AIR main unit, place it more than
8 m (26
1/ 4
feet) away from the S-AIR main unit you
are using.
• Confirm the S-AIR IDs of the unit and the S-AIR
main unit.
• Check the pairing setting.
• Place so that the unit and the S-AIR main unit are
closer.
• Stop using any equipment that generates
electromagnetic energy such as a microwave oven.
• Place so that the unit and the S-AIR main unit are
separated from other wireless devices.
• Stop using any other wireless devices.
• Change the S-AIR ID settings of the unit and the S-
Al R main unit.
··I'urn off the unit and S-AIR main unit and then turn
them on again.
• Check that the power cord is connected securely and
the unit is turned on.
• Check that headphones are not connected to the
r::
(headphone) jack on the rear of the unit.
• [ncrease the volume of the unit.
There is noise or the sound skips.
·11' you usc another S-AIR main unit, place it more than
8 m (26
1/. 1
feet) away from the S-AIR main unit you
are using.
• Place so that the unit and the S-AIR main unit are
doseI'.
• Stop using any equipment that generates
electromagnetic energy such as a microwave oven.
• Place so that the unit and the S-AIR main unit are
separated from other wireless devices.
• Stop using any other wireless devices.
• Change the S-AIR ID settings of the unit and the
s-
Al R main unit.
• Do not place a mobile phone near the unit, as this may
result in noise.
To reset the unit to factory settings
If the unit still does not operate properly, reset the unit
to factory settings.
Disconnect and reconnect the power cord, and
then turn on the unit.
Press.
[1],
DISPLAY
[ID
and
lit! IT]
at the same
time.
All user-configured settings, such as timer, clock, etc.
are deleted.
Messages
CANCEL: Time out without pairing.
COMPLETE: Pairing is completed.
10 A: Sets the S-AIR ID to "A:'
10 B : Sets the S-AIR ID to "8."
10 C: Sets the S-AIR ID to
"c:'
LINKED: The unit is connected to the S-AIR main unit.
PAIRING: Pairing is in progress.
S-AIR : Displayed from the point power of the unit is
turned on until connection with the S-AIR main unit
is established.
TIME NG : The Play Timer start and end times are set to
the same time.
UNLINKED: Displayed when the connection with the
S-AIR main unit is cut off.
Specifications
Amplifier section
U.S.A. model:
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL HARMONIC
DISTORTION:
With 3 ohm loads, both channels driven, from
300 - 20,000Hz; rated 4 watts per channel minimum
RMS power, with no more than 10% total harmonic
distortion from 250 milliwatts to rated output.
Other models:
Continuous RMS power output (reference):
4
+
4 W (3 ohms at 1 kHz, 10% THD)
Output
':: (stereo mini jack): Accepts headphones with an
impedance of 8 ohms or more
Speaker section
Speaker system: Full range, bass-reflex type
Speaker units: 65 mm, cone type (2)
Nominal impedance: 3 ohms
Wireless transceiver (EZW-RTl 0)
Communication System: S-AIR Specification version 1.0
Output: 12.0 mW
Frequency band: 2.4000 GHz - 2.4835 GHz
Modulation method: DSSS
Power requirements: DC 3.3 V, 350 mA
Dimensions (w/h/d): 50 mm
x
13 mm
x
60 mm
(2 x 171.~2 x 2
3/ x
in)
Mass: 24 g (I oz)
General
Power requirements:
North American model: 120
V
AC, 60 Hz
Oceanian model: 230 - 240 V AC, 50/60 Hz
Power consumption: 15 W
Dimensions (w/h/d): Approx. 300 x 136 x 115 mm
(I
1'1, x 5 'I, x 4 'I, in)
Mass: Approx. 2.2 kg (41b 14 oz)
Supplied accessories: Wireless transceiver EZW-RTIO
(I)
Design and specifications are subject to change without
notice.
• Standby power consumption: 1.0 W
• Halogenated flame retardants are not
used in the certain printed wiring
boards.
• Halogenated flame retardants are n.ot
used in cabinets (Except for the U.S.A.
model).