Sony S-AIR AIR-SA50R Operating Instructions

4-147-597-11(1)

Wireless Speaker

Operating Instructions
Manual de instrucciones
(reverso)
AIR-SA50R
©2009 Sony Corporation Printed in China
CAUTION
WARNING
You are cautioned that any changes or
modifications not expressly approved
To reduce the risk of fire
in this manual could void your
or electric shock, do not
authority to operate this equipment.
expose this apparatus to
For the wireless transceiver (EZW-RT10A)
This device complies with Part 15 of
rain or moisture.
the FCC Rules. Operation is subject to
To reduce the risk of fire or electric
the following two conditions: (1) this
shock, do not expose this apparatus to
device may not cause harmful
dripping or splashing, and do not place
interference, and (2) this device must
objects filled with liquids, such as
accept any interference received,
vases, on the apparatus.
including interference that may cause
undesired operation.
As the main plug is used to disconnect
the unit from the mains, connect the
This equipment must not be co-located
unit to an easily accessible AC outlet.
or operated in conjunction with any
Should you notice an abnormality in
other antenna or transmitter.
the unit, disconnect the main plug
from the AC outlet immediately. This equipment complies with FCC
radiation exposure limits set forth for
The unit is not disconnected from the
uncontrolled equipment and meets the
mains as long as it is connected to the
FCC radio frequency (RF) Exposure
AC outlet, even if the unit itself has Guidelines in Supplement C to OET65.
been turned off.
This equipment should be installed
Do not install the appliance in a
and operated with at least 20cm and
confined space, such as a bookcase or
more between the radiator and person's
built-in cabinet.
body (excluding extremities: hands,
wrists, feet and ankles).
Do not expose batteries or apparatus
with battery-installed to excessive heat
 "S-AIR" and its logo are trademarks of
such as sunshine, fire or the like.
Sony Corporation.
 The Bluetooth word mark and logos are
The dating code and the nameplate are
owned by the Bluetooth SIG, Inc. and any
located on the bottom exterior of the
use of such marks by Sony Corporation is
unit.
under license. Other trademarks and trade
names are those of their respective owners.
Owner's Record
 iPod is a trademark of Apple Inc.,
The model and serial numbers are
registered in the U.S. and other countries.
located on the bottom of the unit.
 iPhone is a trademark of Apple Inc.
Record these numbers in the space  All other trademarks and registered
provided below. Refer to them trademarks are of their respective holders.
In this manual, ™ and ® marks are not
whenever you call upon your Sony
specified.
dealer regarding this product.
Model No.
Serial No.
Features
Important Safety Instructions
1) Read these instructions. The AIR-SA50R is an "S-AIR"
compatible product. It is also called the
2) Keep these instructions.
"S-AIR sub unit. "
3) Heed all warnings.
Connecting the S-AIR main unit
4) Follow all instructions.
(transmitter product, hereafter called
5) Do not use this apparatus near
water. "main unit") with the S-AIR sub unit
(receiver product, hereafter called "sub
6) Clean only with dry cloth.
7) Do not block any ventilation unit") using "S-AIR" technology, you
can use each unit in a remote location.
openings. Install in accordance
For example, you can install this unit
with the manufacturer's
in the bedroom, and then install the
instructions.
main unit in the living room. You can
8) Do not install near any heat
sources such as radiators, heat then listen to the music from the main
unit located in the living room with
registers, stoves, or other apparatus
(including amplifiers) that produce this unit in the bedroom.
This unit is compatible with a main
heat.
unit with "MULTI SOURCE" mode,
9) Do not defeat the safety purpose of
and the coupling operation. The
the polarized or grounding-type
coupling operation establishes a
plug. A polarized plug has two
blades with one wider than the connection between the sub unit and
optional S-AIR remote commander.
other. A grounding type plug has
two blades and a third grounding
prong. The wide blade or the third
prong are provided for your safety.
Precautions
If the provided plug does not fit
into your outlet, consult an
Notes on use of the S-AIR
electrician for replacement of the
product
obsolete outlet.
10) Protect the power cord from being  As the S-AIR product transmits
walked on or pinched particularly sound by radio waves, sound may
at plugs, convenience receptacles, skip when radio waves are
and the point where they exit from obstructed. This is a characteristic of
the apparatus. radio waves and is not a
11) Only use attachments/accessories
malfunction.
specified by the manufacturer.  As the S-AIR product transmits
12) Use only with the sound by radio waves, equipment
cart, stand, tripod, that generates electromagnetic
bracket, or table energy, such as a microwave oven,
specified by the may interfere with sound
manufacturer, or transmission.
sold with the
 As the S-AIR product uses radio
apparatus. When a cart is used, use waves that share the same frequency
caution when moving the cart/ as other wireless systems, such as
apparatus combination to avoid wireless LAN or Bluetooth devices,
injury from tip-over. interference or poor transmission
13) Unplug this apparatus during
may result. In this case, take the
lightning storms or when unused following steps:
for long periods of time.  Do not install the S-AIR product
14) Refer all servicing to qualified near other wireless systems.
service personnel. Servicing is  Do not use the S-AIR product
required when the apparatus has and other wireless systems at the
been damaged in any way, such as same time.
power-supply cord or plug is
 The transmission distance differs
damaged, liquid has been spilled or depending on the usage
objects have fallen into the
environment. Find a location where
apparatus, the apparatus has been transmission between the unit and
exposed to rain or moisture, does the S-AIR main unit is most
not operate normally, or has been effective, and install the unit and the
dropped. S-AIR main unit there.
NOTE: On safety
This equipment has been tested and  Operate the unit only on the power
found to comply with the limits for a sources specified in "Specifications".
Class B digital device, pursuant to Part  Completely disconnect the power
15 of the FCC Rules. These limits are supply cord from the wall socket
designed to provide reasonable
(mains) if the unit is not going to be
protection against harmful interference used for an extended period of time.
in a residential installation. This When unplugging the unit, always
equipment generates, uses and can grip the plug. Never pull by the cord
radiate radio frequency energy and, if itself.
not installed and used in accordance
 Should any solid object or liquid get
with the instructions, may cause into the unit, unplug the unit, and
harmful interference to radio
have it checked by qualified
communications. However, there is no personnel before operating it again.
guarantee that interference will not  The power supply cord can be
occur in a particular installation. If this changed only by a qualified service
equipment does cause harmful facility.
interference to radio or television
On placement
reception, which can be determined by
 At low temperature, characters
turning the equipment off and on, the
change in the display becomes slow,
user is encouraged to try to correct the
but it is not a malfunction.
interference by one or more of the
 Do not place the unit in an inclined
following measures:
position or in locations that are
 Reorient or relocate the receiving
extremely hot, cold, dusty, dirty,
antenna.
humid or lacking adequate
 Increase the separation between the
ventilation, subject to vibration,
equipment and receiver.
direct sunlight or bright light.
 Connect the equipment into an
 Be careful when placing the unit on
outlet on a circuit different from surfaces that have been specially
that to which the receiver is
treated (for example, with wax, oil,
connected. polish) as staining or discoloration
of the surface may result.
 Consult the dealer or an
experienced radio/TV technician
for help.
On heat buildup
S-AIR (Sony Audio
 Heat buildup in the unit during
Interactive Radio frequency)
operation is normal and is not cause
Recent times have seen the rapid
for alarm.
spread of DVD media, Digital
 Do not touch the cabinet if it has
Broadcasting, and other high-
been used continuously at a high
quality media.
volume because the cabinet may
To ensure that the subtle nuances of
have become hot.
these high-quality media are
On the speaker system
transmitted with no deterioration,
This speaker system is not
Sony has developed a technology
magnetically shielded, and the picture
called "S-AIR" for the radio
on nearby TV sets may become
transmission of digital audio signals
magnetically distorted. In this
with no compression, and has
situation, turn off the TV, wait about
incorporated this technology into
15 to 30 minutes, and turn it back on. the EZW-RT10A.
If there is no improvement, move the
This technology transfers digital
unit far away from the TV.
audio signals with no compression
using the 2.4 GHz band range of
Cleaning the cabinet
ISM band (Industrial, Scientific, and
Clean the cabinet with a soft dry cloth.
Medical band), such as wireless
Do not use any type of abrasive pad,
LANs and Bluetooth applications.
scouring powder, or solvent, such as
thinner, benzine, or alcohol.
Getting Started
EZW-RT10A
Wireless transceiver
To a wall socket
Hooking up the unit
After pairing
The connection is established between
 Wireless transceiver
the paired main unit and sub unit.
Insert the supplied wireless transceiver
Your system Neighboring
(EZW-RT10A) securely into the EZW- system
RT10 slot on the rear panel of the unit.
Check the orientation of the  mark
Main unit
when inserting the supplied wireless
ID:A
transceiver (EZW-RT10A). Failure to
do so may result in damage to the unit.
not connected
Push to insert the wireless transceiver
firmly until you cannot see it from the
side.
ID:A ID:A
Sub unit  Sub unit 
Pairing
1
Place the sub unit to be paired
near the main unit.
Pair the main unit with the sub
unit one at a time.
Notes
2
Check that the power of the
 Make sure to turn off the unit when
main unit and the sub unit are
inserting or removing the supplied wireless
turned on.
transceiver (EZW-RT10A). Failure to do so
may result in damage to the unit.
3
 Do not touch the terminals of the supplied Check that the S-AIR ID of the
wireless transceiver (EZW-RT10A).
main unit is the same as the
 Do not insert any device other than the
S-AIR ID of the sub unit.
supplied wireless transceiver (EZW-
RT10A) into the EZW-RT10A slot.
4
Operate the S-AIR main unit to
 S-AIR ID selector
turn on the pairing function.
Set the same S-AIR ID for this unit and
For details on turning on the
the S-AIR main unit to be connected.
pairing function, refer to the
For details on setting the S-AIR ID, see
Operating Instructions supplied
"Establishing the connection with an
with the S-AIR main unit.
S-AIR main unit. "
5
Press the PAIRING button on

Power
the rear panel of the unit using
Connect the power supply cord to a
wall socket. a pointed object.
Notes on turning off the unit "PAIRING" is displayed as a
 The STANDBY indicator on the top of the message in the display. When
unit lights up while the power is off.
completed, the display message
 After you turn off the unit, no operation is
changes to "COMPLETE!" and
effective while "STANDBY" is blinking in
stays on for a few seconds.
the display.
"PAIRING" in the display turns on
 AUDIO IN jack
at the same time.
Connect an audio cable with stereo
To cancel pairing
mini plug (not supplied) to listen to
Change the S-AIR IDs of the unit and
sound of external equipment.
the S-AIR main unit to different S-AIR
IDs.
To stop the pairing operation
midway
Press the PAIRING button again.
To pair the main unit with
multiple sub units
Repeat steps 1 through 5.
Inserting the batteries in
the supplied infrared
Audio cable
remote
(not supplied)
To audio equipment
Slide and remove the battery
(not supplied)
compartment lid, and insert the two
supplied R03 (size AAA) batteries, 
Establishing the side first, matching the polarities
shown below.
connection with an S-AIR
main unit
Connect the unit and S-AIR main unit
to listen to sound from the S-AIR main
unit.
You can easily establish the connection
by setting the same S-AIR ID for this
unit and S-AIR main unit.
1
Operate the S-AIR main unit to
turn on the S-AIR function.
Notes on using the remote
For details on turning on the S-AIR  With normal use, the batteries should last
for about six months.
function, refer to the Operating
 Do not mix an old battery with a new one
Instructions supplied with the
or mix different types of batteries.
S-AIR main unit.
 If you do not use the remote for a long
2
Set the S-AIR ID of the unit to period of time, remove the batteries to
avoid damage from battery leakage and
the same S-AIR ID as the S-AIR
corrosion.
main unit to be connected.
Setting the clock
For details on setting the S-AIR ID
of the S-AIR main unit, refer to the
1
Operating Instructions supplied Connect the power supply cord
with the S-AIR main unit. to a wall socket.
3
"--:--" is displayed when the unit is
Press  to turn on the unit.
connected to the power for the first
Once the connection is established,
time, or after a power interruption.
the S-AIR indicator on the unit
2
lights up and "LINKED" appears in Press CLOCK/TIMER to start
the display for a few seconds.
setting.
"12" and "AM" blink in the display.
Identifying the main unit
3
Press / repeatedly to
with a specific sub unit
adjust the hour, and then press
(Pairing operation)
ENTER to confirm.
It is easy to set the same S-AIR ID for
The minute digits blink in the
the main unit and the sub units to
display.
establish the connection.
4
Press / repeatedly to
However, if a neighbor has an S-AIR
main unit with the same S-AIR ID as adjust the minute, and then
your S-AIR main unit, the neighbor
press ENTER to confirm.
may be able to hear the audio
The clock is set.
transmitted from your S-AIR main
unit on the neighbor's system. Also,
Adjusting the clock
you may be able to hear the audio
transmitted from your neighbor's
1
Press CLOCK/TIMER to adjust
S-AIR main unit on your system. To
the clock.
prevent this, you can identify the main
"TIMER SET" or "TIMER ON/
unit with a specific sub unit by
OFF" appears.
performing the pairing operation.
2
Press  to display "CLOCK
Before pairing
SET," and then press ENTER.
The connection is established by the
S-AIR ID (example).
The hour blinks in the display.
3
Your system Neighboring Press / repeatedly to
system
adjust the hour, and then press
ENTER to confirm.
Main unit
The minute digits blink in the
ID:A
display.
4
Press / repeatedly to
adjust the minute, and then
press ENTER to confirm.
The clock is adjusted.
Note
The clock set procedure will be canceled in
ID:A ID:A
the following cases:
Sub unit  Sub unit 
– When CLOCK/TIMER is pressed while
setting.
– The clock set procedure will be canceled if
no operation is performed for 65 seconds.
Unit
STANDBY indicator
/ (power)
Wireless strength
S-AIR indicator
Touch sensitive buttons
Operation using the touch
Remote sensor sensitive button that beeps.
Operations
Listening to the sound of Using the Timers
the connected S-AIR main
Sleep Timer
unit
This timer turns off the unit
automatically after a preset duration,
You can use the S-AIR function to
allowing you, for example, to fall asleep
listen to the sound of an S-AIR main
while listening to music.
unit in a remote location.
1
Make sure the power of the unit
1
Perform the procedure
is on.
described in "Establishing the
connection with an S-AIR main
2
Press SLEEP/BRIGHT repeatedly
unit" and check that the S-AIR
to set the duration.
indicator is lit.
Each time you press
2 SLEEP/BRIGHT, the duration
Press S-AIR CH +/– repeatedly
decreases from 90 minutes in 10-
to select the desired S-AIR
minute increments.
channel of the S-AIR main unit.
Depending on the connected
S-AIR main unit, the operations
may differ. For details, refer to the 3
Press the SLEEP/BRIGHT button
Operating Instructions supplied
until the desired duration is
with the S-AIR main unit.
displayed.
3
Press VOLUME +/– to adjust the
The setting becomes effective after
volume.
4 seconds.
Notes
To operate the S-AIR main unit
 Even if you set the Sleep Timer, no sound
from the unit
is output from the unit if playback on the
You can perform the following
connected S-AIR main unit ends within
operations using the buttons on the the set time period or if communication
remote or unit. with the S-AIR main unit is cut off.
 To check remaining time, press
To Press
SLEEP/BRIGHT once. To change the
duration, press SLEEP/BRIGHT
Start playback. 
repeatedly. To cancel the Sleep Timer, press
Stop playback. 
SLEEP/BRIGHT repeatedly until "SLEEP
OFF" is displayed.

Pause playback.
 If the Play Timer is activated while the
Select sound source. S-AIR CH +/–
Sleep Timer is in operation, the remaining
time of the Sleep Timer will be canceled
Select track. /
and then the end time of the Play Timer
Depending on the connected S-AIR
will become effective.
main unit, the operation may differ.
Play Timer
Refer to the Operating Instructions of
This timer turns the unit on and off
the S-AIR main unit.
according to the clock. "S-AIR" or
Note
"ALARM" is selectable as the alarm
When the main unit is used in combination
sound source.
with an iPod or iPhone, S-AIR unit button
You can wake up to the sound of the
operation of the iPod or iPhone will be as
connected S-AIR main unit.
follows.
Operations with To set the Play Timer
Status of
S-AIR units
the iPod or 1
Make sure the clock is set.
iPhone
 or  
To adjust the clock, see "Adjusting
Playback Pause Pause the clock. "
Pause Playback No change
2
Press CLOCK/TIMER to start
Off Playback LCD on
setting.
To change the information on
"TIMER SET" blinks in the display.
(If "TIMER ON/OFF" blinks, the
the display while the unit is on
Play Timer is already set.)
Press DISPLAY.
Each time you press the button, the 3
Press ENTER to set start time.
display changes as follows:
The hour digits blink in the display.
4
When the unit is connected to an S-AIR
Press / repeatedly to
main unit:
adjust the hour, and then press
Information of connected main unit 
ENTER to confirm.
Model name of connected main unit
 Clock of the unit  ... The minute digits blink in the
display.
Up to 16 characters of information can
5
Press / repeatedly to
be displayed.
adjust the minute, and then
press ENTER to confirm.
When the unit is not connected to an
S-AIR main unit:
The start time is set.
"S-AIR"  "UNLINKED"  Clock of
6
the unit  ... Repeat the same procedure in
step 4 and 5 for setting the end
Listening to the sound of
time.
an external equipment
The end time should be at least 1
minute after the start time.
You can enjoy the sound from an
7
externally-connected non-S-AIR Press / alternately to
equipment.
select the sound source.
1
Connect the AUDIO IN jack of The default sound source is
"ALARM. " Press  to select
the unit to the LINE OUT (AUDIO
"S-AIR. "
OUT) jack or headphone jack of
8
the external equipment using
Press ENTER to start the timer.
an audio connecting cable (not
 is displayed. "PLAY TIMER"
supplied).
message, start time and then end
time appear in the display.
2
Press S-AIR/AUDIO IN to display
To cancel the Play Timer setting midway
"AUDIO IN."
The timer set procedure will be
canceled in the following cases:
3
Start playback of the connected
– When CLOCK/TIMER is pressed
equipment.
while setting.
4 – If no operation is performed for 65
Press VOLUME +/– to adjust the
seconds.
volume.
Notes
Notes
 To change the start time or end time of the
 If the connected equipment has both LINE
Play Timer, start over from step 2.
OUT (AUDIO OUT) jacks and headphone
 For details on configuring the S-AIR
jack, connect to the LINE OUT (AUDIO
sound source, refer to the Operating
OUT) jacks for better sound quality. Instructions supplied with the S-AIR main
Connecting to the headphone jack at high
unit.
volume may cause distortion.
To stop the "ALARM" sound of
 If the connected equipment has tone
the Play Timer
adjustment functions (such as bass boost,
equalizer, etc.), set them to off when
When the start time is reached,
listening via this unit. If they are activated,
"ALARM" sounds and continues to
sound may be deteriorate or distort.
sound progressively louder at short
intervals. To stop the sound before the
Changing the brightness
end time, press any key on the unit.
of the display
"ALARM" volume level cannot be
adjusted.
When the unit is turned off, the clock
is displayed. You can turn off the clock
When "S-AIR" is selected as the
display by adjusting the brightness.
source for the Play Timer
Pressing SLEEP/BRIGHT while the
When you select "S-AIR" sound, the
power of the unit is off changes the
unit turns on about 45 seconds before
display brightness as follows:
the start time to make the S-AIR
connection with the main unit (the
Bright  Darkens  Off  Bright
power of the main unit should be on).
 ...
When the S-AIR connection is
successful, playback of the main unit
will start at the set time. If the S-AIR
connection is unsuccessful, the sound
will automatically be switched to the
"ALARM" sound.
When the Play Timer for "S-AIR"
starts, the unit resumes the last volume
setting made when the unit was on.
Notes
 If you press S-AIR/AUDIO IN after the
start time of the Play Timer with "S-AIR"
sound, the Play Timer operation is
terminated at that point. The end time will
be disregarded.
 If the unit is kept turned on by the start
time, the Play Timer sounds at the current
volume level.
Remote (RM-ANU065)
SLEEP/BRIGHT
/ (power)
S-AIR/AUDIO IN
Troubleshooting
1
To deactivate the Play Timer Make sure the power supply
cord is correctly and firmly
1
Press CLOCK/TIMER.
connected.
"TIMER ON/OFF" blinks in the
2
display. (If "TIMER SET" blinks, Find your problem in the
the Play Timer is not set.)
checklist below, and take the
2 indicated corrective action.
Press ENTER.
"TIMER ON" blinks in the display.
3 If the issue persists, contact your
Press  to change the
nearest Sony dealer.
display to "TIMER OFF."
When bringing this unit in for
 disappears.
repairs, be sure to bring in the entire
4 system (this unit, the S-AIR main
Press ENTER.
unit and wireless transceivers).
Note This product is a system product,
To activate the Play Timer again, make sure
and the entire system is needed to
"TIMER ON" is blinking in the display in
determine the location requiring
step 2, and then press ENTER.
repair.
Turning off the supplied
infrared remote control If the STANDBY indicator flashes
Immediately unplug the power supply
function
cord.
In addition to the unit you already After the STANDBY indicator stops
have, you can connect other S-AIR sub flashing, reconnect the power supply
units to a single S-AIR main unit and cord, and turn on the unit. If the issue
use them together. persists, contact your nearest Sony
However, when using multiple S-AIR
dealer.
sub units near each other, all the S-AIR
The remote does not function.
sub units may receive the same signal
 Remove any obstacles between the
from the remote and the connected
remote and the remote sensor on the
S-AIR main unit may not function
unit, and position the unit away
properly. To prevent this, you can turn
from fluorescent lights.
off the remote control function of the
 Point the remote at the remote
S-AIR sub units.
sensor on the unit.
Use buttons on the S-AIR sub unit
 Move the remote closer to the unit.
whose remote control function you
 The remote control function is off.
want to turn off.
Turn on the remote control function.
1
Press  to turn off the unit.
The S-AIR indicator is turned off.
2  Check that the power supply cord is
Press and hold S-AIR CH+, and
connected securely and the unit is
then press .
turned on.
"REMOTE OFF" is displayed, and
 Check that the supplied wireless
the setting is complete. Even when
transceiver is inserted securely to the
you try controlling the unit using
unit.
the remote, "REMOTE OFF" is
Connecting the unit and S-AIR
displayed and the unit will not
main unit is not possible. (The
accept the signal from the remote.
S-AIR indicator flashes.)
To turn on the remote control
 Check that the supplied wireless
function
transceiver is inserted securely to the
Perform steps 1 and 2 above and check
unit.
that "REMOTE ON" appears in the
 If you use another S-AIR main unit,
display.
place it more than 8 m (26 1 / feet)
4
Note
away from the S-AIR main unit you
Even when the remote control function is
are using.
turned off,  and VOLUME +/– on the
 Confirm the S-AIR IDs of the unit
remote will continue to function.
and the S-AIR main unit.
 The main unit is paired with another
Enjoying different sound
S-AIR sub unit. Pair the main unit
source with multiple sub
with the sub unit you are using.
units  The main unit is paired with another
S-AIR sub unit. Cancel pairing.
Use a main unit that can set the
 Place so that the unit and the S-AIR
MULTI SOURCE mode.
main unit are separated from other
When selecting the MULTI SOURCE
wireless devices.
mode, you can listen to a different
 Stop using any other wireless
sound source with each sub unit.
devices.
For setting up and details, refer to the
 The connected S-AIR main unit is
Operating Instructions of the main
turned off. Turn on the S-AIR main
unit.
unit.
To identify the unit using the
The S-AIR channel fails to
optional** S-AIR remote
change.
commander AIR-RM10
 Check that the unit and the S-AIR
(Coupling operation) main unit are connected properly.
This unit is compatible with the  When using the Wireless Audio
coupling operation. The coupling Transmitter for PC as the S-AIR
operation establishes a connection main unit, sub unit operations will
between the sub unit and optional** not be functional if supplied PC
S-AIR remote commander. For details, application is not booted or
refer to the Operating Instructions of Standard Mode is selected.
the optional** S-AIR remote
There is no sound.
commander.
 If you use another S-AIR main unit,
When coupling is in progress,
place it more than 8 m (26 1 / feet)
4
"COUPLING..." is displayed.
away from the S-AIR main unit you
When completed, the display message
are using.
changes to "COUPLING OK" and
 Confirm the S-AIR IDs of the unit
stays on for a few seconds. "CPL" in
and the S-AIR main unit.
the display turns on at the same time.
 Check the pairing setting.
 Place so that the unit and the S-AIR
About the error message when setting
the coupling operation main unit are closer.
 Stop using any equipment that
"INVALID" is displayed if the
generates electromagnetic energy,
S-AIR main unit is not compatible
such as a microwave oven.
with the MULTI SOURCE mode or the
 Place so that the unit and the S-AIR
coupling operation.
main unit are separated from other
"FAILED" or "ERROR" is displayed if
wireless devices.
an error occurs while setting the
 Stop using any other wireless
coupling operation.
devices.
 Change the S-AIR ID settings of the
For details on the coupling operation,
unit and the S-AIR main unit.
refer to the Operating Instructions of
 Turn off the unit and S-AIR main
the optional** S-AIR remote
unit and then turn them on again.
commander.
 Check that the power supply cord is
connected securely and the unit is
Turning off the beep sound
turned on.
of the touch sensitive  Increase the volume of the unit.
There is noise or the sound
buttons
skips.
You can turn off beep sound when pressing
 If you use another S-AIR main unit,
the buttons on the front panel of the unit,
place it more than 8 m (26 1 / feet)
such as ,  or .
4
away from the S-AIR main unit you
1
Press  to turn off the unit.
are using.
 Place so that the unit and the S-AIR
2
Press and hold S-AIR/AUDIO IN,
main unit are closer.
and then press .
 Stop using any equipment that
"BEEP OFF" is displayed, and the
generates electromagnetic energy,
setting is complete. such as a microwave oven.
 Place so that the unit and the S-AIR
To turn on the beep sound
main unit are separated from other
Perform steps 1 and 2 above and check that
wireless devices.
"BEEP ON" is displayed.
 Stop using any other wireless
devices.
 Change the S-AIR ID settings of the
unit and the S-AIR main unit.
 Do not place a mobile phone near
the unit and the S-AIR main unit, as
this may result in noise.
Messages
CANCEL : Time out without pairing.
COMPLETE! : Pairing is completed.
S-AIR ID A : Sets the S-AIR ID to "A. "
S-AIR ID B : Sets the S-AIR ID to "B. "
S-AIR ID C : Sets the S-AIR ID to "C. "
LINKED : The unit is connected to the
S-AIR main unit.
PAIRING : Pairing is in progress.
REMOTE OFF : The unit is not
accepting signals from the remote
because the remote control function
is set to "REMOTE OFF. "
REMOTE ON : Displayed when the
remote control disable mode is
cleared.
OFF TIME NG! : The Play Timer start
and end times are set to the same
time.
S-AIR : Displayed from the point
power of the unit is turned on until
connection with the S-AIR main
unit is established.
UNLINKED : The connection with the
S-AIR main unit is cut off.
AUDIO IN : Displayed when you press
the S-AIR/AUDIO IN button to
listen to external equipment.
Specifications
Amplifier section
AUDIO POWER SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
With 8 ohms loads, both channels
driven, from 100 – 15,000Hz; rated 6
watts per channel minimum RMS
power, with no more than 10% total
harmonic distortion.
Continuous RMS power output
(reference):
8 + 8 watts (8 ohms at 1 kHz, 10%
harmonic distortion)
Speaker section
Speaker system: Full range, bass-reflex
type
Speaker units: 57 mm (2 / in), cone
1
4
type (2)
Nominal impedance: 8 ohms
Wireless transceiver
(EZW-RT10A)
Communication System: S-AIR
Specification version 1.0
Frequency band: 2.4000 GHz 
2.4835 GHz
Modulation method: DSSS
Power requirements: DC 3.3 V,
350 mA
Dimensions (w/h/d): 50 × 13 × 60 mm
(2 × 17 / × 2 3 / in)
32 8
Mass: 24 g (1 oz)
General
Power requirements: 120 V AC, 60 Hz
Input: AUDIO IN jack (ø 3.5 mm stereo
minijack)
Dimensions (w/h/d): Approx. 250 ×
123 × 129 mm (9 / ×4 / ×5 / in)
7 7 1
8 8 8
Mass: Approx. 1.4 kg (3 lb 1.8 oz)
Supplied accessories: Wireless
transceiver (EZW-RT10A) (1)/
Remote commander (RM-ANU065) (1)*/
R03 (size AAA) batteries (2)*
* When you purchase this product with main
unit and sub units system package product,
the pieces of these accessories may differ.
Refer to the manuals supplied with the
package product.
Design and specifications are subject
to change without notice.
** Some package products include an S-AIR
remote commander and some do not
include it.