General Information; Parts Included In The Kit; Cabinet Or Wall Cutout; Electrical Outlet Location - Viking Designer Microwave Built-In Trim Kit Installation Manual

General Information

Parts Included in the Kit

Item
1
2
3
4
5
6
7
8
1) Frame Assembly: QTY 1
2) Bottom Duct Assembly: QTY 1
1
QTY 1 2) Bottom Duct Assembly: QTY 1
2
3) Mouting Bracket: QTY 2
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
6
QTY 2 4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
E E
1) Frame Assembly: QTY 1
Part Name
Frame Assembly
Bottom Duct
Mounting Bracket
Screw A :1-3/16" length
Screw B: 1-3/4" length
Side Decoration (Surface Mount Only)
Surface Mounting Template
Flush Mounting Template
3) Mouting Bracket: QTY 2
3
5
7
Maximum Cutout Opening Width 28" (711.2 mm)
Minimum Cutout Opening Width 27-3/4" (704.9 mm)
1. Align the Surface Mounting Template center line with the
2. Predrill 4 holes marked
Center Line
3. Cut the cabinet opening between the minimum and
BUILT-IN TRIM KIT
SURFACE MOUNTING TEMPLATE
4. Remove template from the cabinet.
FOR DESIGNER SERIES MICROWAVE OVEN
14-1/4" (361.95 mm)
14" (355.6 mm)
Floor Line of Cutout Opening
8
CABINET CUTOUT LINE
Cutout Opening Width 29-5/8" (752.5 mm)
CABINET CUTOUT LINE CABINET CUTOUT LINE
BUILT-IN TRIM KIT
FLUSH MOUNTING TEMPLATE
FOR DESIGNER SERIES MICROWAVE OVEN
FIGURE 1
FIGURE 3
FIGURE 2
CENTER LINE
14" (355.9 mm)
14-13/16" (376.2 mm)
FLOOR LINE OF CUTOUT OPENING

Cabinet or Wall Cutout

QTY
Cutout Dimensions
1
Height A
1
2
2
Width B
4
2
1
1 Depth C
2) Bottom Duct Assembly: QTY 1
1
4
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)

Electrical Outlet Location

Outlet should noT be in the shaded area as
indicated on figure 1.
NOTES:
center of the cabinet. Align the Floor Line with the bottom
of the cabinet at the desired height. Tape it into place.
with a " drill bit.
maximum cutout opening lines. Be careful to cut precisely
along the Floor Line of the cutout.
• If the Depth (C) dimension is greater than 21"
(53.3 cm), the outlet location may be in any
area on the rear wall.
• The floor of the opening should be constructed
of plywood strong enough to support the weight
of the oven and floor load (approximately 100
pounds). The floor should be level for proper
operation of the oven. Be sure to check the
local building code as it may require that the
opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven
does not require the enclosure.
4 4
2) Bottom Duct Assembly: QTY 1
Flush Surface
Mount Mount
Minimum 17-5/16" 16-9/16"
(439.8mm) (420.7mm)
Maximum N/A 16-13/16"
(427mm)
Minimum 29-5/8" 27-3/4"
(752.5mm) (704.9mm)
Maximum N/A 28"
(711.2mm)
20" 20"
Minimum
4) SIDE DECORATION: QTY 2
(503mm) (503mm)
(SURFACE MOUNTING ONLY)
CAUTION