General Information; Parts Included In The Kit; Cabinet Or Wall Cutout; Electrical Outlet Location - Viking RDMOS201SS Installation Instructions Manual

General Information

Parts Included in the Kit

Item
Frame Assembly
1
Bottom Duct
2
Mounting Bracket
3
Screw A :1-3/16" length
4
Screw B: 1-3/4" length
5
Side Decoration (Surface Mount Only)
6
Surface Mounting Template
7
Flush Mounting Template
8
1) Frame Assembly: QTY 1
2) Bottom Duct Assembly: QTY 1
1
1 2) Bottom Duct Assembly: QTY 1
2
3) Mouting Bracket: QTY 2
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
6
2 4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)
8
E E
1) Frame Assembly: QTY 1
Part Name
3) Mouting Bracket: QTY 2
3
4
5
7
Maximum Cutout Opening Width 28" (711.2 mm)
Minimum Cutout Opening Width 27-3/4" (704.9 mm)
1. Align the Surface Mounting Template center line with the
center of the cabinet. Align the Floor Line with the bottom
of the cabinet at the desired height. Tape it into place.
2. Predrill 4 holes marked A with a ¹₁₆" drill bit.
Center Line
3. Cut the cabinet opening between the minimum and
BUILT-IN TRIM KIT
maximum cutout opening lines. Be careful to cut precisely
SURFACE MOUNTING TEMPLATE along the Floor Line of the cutout.
4. Remove template from the cabinet.
FOR DESIGNER SERIES MICROWAVE OVEN
14-1/4" (361.95 mm)
14" (355.6 mm)
1/4"
(6.2 mm)
Floor Line of Cutout Opening
CABINET CUTOUT LINE
Cutout Opening Width 29-5/8" (752.5 mm)
CABINET CUTOUT LINE CABINET CUTOUT LINE
Edges to align Side Spacer Templates (R and L)
BUILT-IN TRIM KIT
FLUSH MOUNTING TEMPLATE
FOR DESIGNER SERIES MICROWAVE OVEN
Side Spacer - L Side Spacer - R
1. Align the Flush Mounting Template center line with the center of the
cabinet. Align the Floor Line with the bottom of the cabinet at the
desired height. Tape it in place.
13/16" Min. 2. Cut the cabinet opening along the three Cabinet Cutout Lines and
FIGURE 1
15/16 Max. the Floor Line.
Side Spacer (2 required)
Must protrude from edge of cabinet 3. Install two Side Spacers (see FIGURE 1) and one Bottom Spacer (see
1-9/16" (39.7 mm)
cutout towards center as shown. FIGURE 2) as specified in FIGURE 3. Be sure to offset all three spacers
Bottom and Side
by 1⁹₁₆" from the front surface of the cabinet.
Spacer (R and L) Offset
4. Cut out the Side Spacer Templates (R and L) and align the indicated
24" min. width edge to the corresponding Side Spacer (see FIGURE 3). Be careful to
27-7/8" max. width Bottom Spacer centered with cabinet cutout
FIGURE 3 align the Floor Line to the bottom edges of the Side Spacers.
5. Predrill two holes indicated "A" in Side Spacer - R with a ¹₁₆" drill bit.
6. Predrill two holes indicated "B" in Side Spacer - L with a ¹₁₆" drill bit.
7. Remove template from the cabinet.
FIGURE 2
Bottom Spacer (1 required) ¹₄" plywood
1/4" (6.35 mm) CENTER LINE 1/4" (6.35 mm)
14" (355.9 mm)
14-13/16" (376.2 mm)
FLOOR LINE OF CUTOUT OPENING
TINSLB009MRR0

Cabinet or Wall Cutout

QTY
Cutout Dimensions
1
Minimum
Height A
1
2
Maximum
2
Minimum
Width B
4
2
Maximum
1
Minimum
1 Depth C
2) Bottom Duct Assembly: QTY 1
1
4) SIDE DECORATION: QTY 2
(SURFACE MOUNTING ONLY)

Electrical Outlet Location

Outlet should noT be in the shaded area as
indicated on figure 1.
noTES:
• If the Depth (C) dimension is greater than 21"
(53.3 cm), the outlet location may be in any
1/4"
(6.2 mm)
area on the rear wall.
TINSLB008MRR0
• The floor of the opening should be constructed
of plywood strong enough to support the weight
of the oven and floor load (approximately 100
pounds). The floor should be level for proper
operation of the oven. Be sure to check the
local building code as it may require that the
opening be enclosed with side, ceiling and rear
partition. The proper functioning of the oven
does not require the enclosure.
4 4
2) Bottom Duct Assembly: QTY 1
Flush Surface
Mount Mount
17-5/16" 16-9/16"
(439.8mm) (420.7mm)
N/A 16-13/16"
(427mm)
29-5/8" 27-3/4"
(752.5mm) (704.9mm)
N/A 28"
(711.2mm)
20" 20"
4) SIDE DECORATION: QTY 2
(503mm) (503mm)
(SURFACE MOUNTING ONLY)
CAUTION