Page 1
CONTRACTOR SERIES SmartSequencer ™ CN-3600SE Instruction Manual CN-3600SE 16 A Maximum For more information call: For additional information refer to the Quick Start Para más información llame al: Guide, included with product packaging. Pour plus de renseignements: www.furmancontractor.com 877-486-4738 DIN-00021-A...
Page 2
The CN-3600SE is a 230VAC 16 ing™ defines a whole new level of power manage- Why choose Furman? At Furman Sound, we have spent the last 30 years and earned the trust and respect of the Profes- technologies. If this is your first Furman Contractor quietly obsessing about AC Power Quality and how sional A/V industry.
AUDIO AND VIDEO CLARITY voltage. When an unsafe condition is detected, a relay shuts off the power to the outlets until Furman’s optional BlueBOLT® RS-232-to- Eth- the EVS condition has subsided. The CN-3600SE ernet adaptor (shown above) provides additional SERIES MULTI-STAGE LINEAR FILTERING...
NOTE: Chain units in series. triggering DELAY 3 DELAY 3 DELAY 3 CLASS 2 WIRING Delay 3 may be utilized with Furman PS-8REII and PS-PROEII GND - Terminal for remote LED status CLASS 2 WIRING CLASS 2 WIRING and/or triggering (CATHODE) COMM/ Rear LED –...
Security and Safety The CN-3600SE is readily adaptable to a wide 4. WARNING: This device is intended for indoor 10. Please, only use accessories specified by the range of installation requests and requirements. use only. Do not use this device in or near water.
DIP Switch is used to set various options on the turned to its 100% value (fully clockwise), the DIP 2 = ON adds 2 minutes to the maximum CN-3600SE. It is also used in combination with time delay will be equal to the maximum time time delay the DLY ADJ pot to adjust the delay range.
Page 7
(NO) or Normally Closed (NC) state. The fac- the REMOTE PORT connector on the rear panel be set to operate the CN-3600SE in a Maintained tory default position for DIP 4 is ON, making of the CN-3600SE. The factory default settings Mode DIP 7 OFF or a Momentary Mode DIP 7 ON.
Voltage returns to a EVS AUTO quencers within the chain will also recover er. If DIP Switch 8 is OFF the CN-3600SE will range within the EVS recovery points. Please see MANUAL when the Primary unit recovers, regardless of operate as a Secondary Sequencer.
If power is provided to the outlets, the Front Panel 16 Amp Breaker: 1) When the CN-3600SE is in FORCE OFF mode LED will illuminate green. If the CN-3600SE is the DELAY lights will blink ON/OFF in unison at a operating under safe power conditions and no 1 second interval.
CLASS 2 WIRING initiate a remote ON or OFF sequence. If a four- FORCE OFF FORCE OFF into the REM pin when the CN-3600SE is config- PRIMARY PRIMARY conductor cable is used, an LED may be installed ured for GND ON mode. This is explained in detail...
3600SE to operate normally. If DIP Switch 4 is state of the DELAY 3 outlet. If the DELAY 3 outlet OFF feature of the CN-3600SE. This is a safety OFF, and the FORCE OFF terminals are open cir- is OFF, the COM terminal will be shorted to the...
SmartSequencer ™ EXAMPLE 2 DIAGRAM - SMALL LEGACY SET-UP RS-1 Maintained CN-3600SE Key Switch CLASS 2 WIRING BACK PANEL TERMINALS CN-3600SE replaces Legacy product 1mm recommended FORCE for purposes of immediate shutdown. STAT STAT PS-8RE II or PS-PRO E II...
Trouble Shooting Guide 1. My CN-3600SE is dead; there are no lights 7. My PROTECTION OK LED is off. SmartSequencing connected systems: or activity upon power up. This usually indicates that the EVS protection For SmartSequencing connected systems you Check the front panel 16 Amp breaker. Reset circuit has become damaged or compromised.
Buying through auction sites or unauthorized www.furmancontractor.com dealers may result in the purchase of salvaged, failed and/or prod- ucts not intended for use in the US. In addition, Authorized Furman Internet dealers have demonstrated sufficient expertise to insure warranty compliant installations.