Identification Of Controls; Antenna Connections; For The Proper Connections; Antenna To Dvd/Vcr Connection - Toshiba SD-V280UA Service Manual

Introduction
Identification of Controls (continued)
The instructions in this manual describe the functions on the remote control. See the page in
Remote control
Power ( ) button 22
TAPE EJECT button 29
Direct channel
selection buttons 28
Number buttons 45
Channel / buttons 34
Direction buttons 45
( / / / )
MENU button*
TOP MENU button 50
SET UP button 53
VCR MENU button 23
TV/VCR button 22
SUB TITLE button 52
ATR button 31
ANGLE button 50
COUNTER RESET
button 32
TIMER REC button 37
MEMORY button 47
ZERO RETURN
button 32
REW button 30
SKIP button 44
INDEX - button 33
34
REC button
OTR button 36
STOP button 30
* MENU button
12
Connections

Antenna connections

If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber, skip ahead to page 16

for the proper connections.

Antenna to DVD/VCR connection

The DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV and

connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an

antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.

1 Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
75 ohm Coaxial Cable
2 Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
Matching Transformer 300 ohm Input 75
ohm output (not supplied)
300 ohm Twin Lead (Flat) Wire
3
Separate VHF and UHF Antennas
Combiner 75/300 ohm Inputs 75 ohm output
UHF
VHF
300 ohm Twin Lead (Flat) Wire
75 ohm Coaxial Cable
Note: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.
Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to
the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor
type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
14
for details.
DVD/VCR button
22
OPEN/CLOSE button 42
54
DISPLAY button
CALL button 24
INPUT SELECT button 40
ENTER button 23
TRACKING +/- buttons 31
SET +/- buttons
23
CANCEL button 37
RETURN button 53
ZOOM button 46
CM SKIP button 31
CLOCK COUNTER
button 33
AUDIO button 51
AUDIO SELECT button 39
PLAY MODE button 48
SP/SLP button 34
A-B RPT button
48
PLAY button 30
FWD button 30
SKIP button 44
INDEX + button 33
PAUSE/STILL button
31
SLOW button
31
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in "DVD Menu."
50
DVD/VCR
IN
(FROM ANT)
OUT
(TO TV)
DVD/VCR
IN
(FROM ANT)
OUT
(TO TV)
DVD/VCR
(not supplied)
IN
(FROM ANT)
OUT
(TO TV)
Inserting Batteries
1
Open the battery compartment 2 Install two "AAA" batteries
cover in the direction of the (supplied), paying attention to the
arrow. polarity diagram in the battery
compartment.
Battery precautions
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Re-
versed batteries may cause damage to the device. To avoid a potential short circuit, insert the "–" end first.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from
possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery
manufacturer's directions.)
Remote control basics
• Press POWER ( ) to turn the DVD/VCR on or off.
• Select your desired operating mode (DVD or VCR) using DVD/VCR.
(DVD or VCR indicator on the front panel will show you which mode is selected.)
• Press CH or CH to move through the channels one channel at a time.
• The CH / ( / ) and SET +/– ( / ) are also used to navigate on-screen menu system.
• You can directly access specific channels using Number buttons.
• Each press of DVD/VCR on the remote control, switches the screen between the VCR screen (VCR mode) and the
DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to
operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of Approx. 7 meters.
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the
connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
TV
VHF/UHF IN
75 ohm Coaxial Cable (supplied)
TV
Splitter 75 ohm Input
UHF
75/300 ohm outputs
75 ohm Coaxial Cable (not supplied)
VHF
(supplied)
TV
UHF
Splitter 75 ohm Input
300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
VHF
(supplied)
3 Replace the compartment
cover.
Approx. 7 meters
13
Note: If a VHF or UHF antenna is used,
set the TV/CATV menu option to
the "TV" mode.
TV with single 75 ohm VHF/UHF antenna
input
Note: If a VHF or UHF antenna is used,
set the TV/CATV menu option to
the "TV" mode.
TV with 300 ohm UHFand 75 ohm VHF
antenna inputs
Note: If a VHF or UHF antenna is used,
set the TV/CATV menu option to
the "TV" mode.
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
15