Identification Of Controls; Connections; Antenna Connections - Toshiba SD-V393SU Service Manual

Introduction
Identification of Controls (Continued)
The instructions in this manual describe the functions on the remote control. See the page in
Remote control
CR D D button
EJECT button ( CR)
'
CLOCK/COUNTER button
!!
CR MENU button
!
SETUP button
##
CM SKIP button
!
ZOOM button
"#
TOP MENU button
"'
Direction buttons ( / / / )
"#
SET+/Ð buttons
!
CH+/Ð buttons
!"
CANCEL button
$
CLEAR button
"#
STOP button
! "
PAUSE/STEP button
! "!
INDEXÐ button
!!
SKIP button
""
REW button
! ""
REC/OTR button
!" !$
TIMER REC button
!%
Direct channel
selection buttons (0Ð9) &
Number buttons (0Ð9)
"#
COUNTER RESET button
!
ANGLE button
"'
ATR button
!
SUBTITLE button
#
MENU button
Use the MENU button to display the menu included on
many DVD video discs. To operate a menu, follow the
instructions in "DVD Menu."
49
12

Connections

Antenna connections

If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead to page 16 for
the proper connections.
Antenna to DVD/VCR connection
The DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV and
connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna
system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.
1
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
75 ohm Coaxial Cable
2 Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
Matching Transformer 300 ohm Input 75
ohm output (not supplied)
300 ohm Twin Lead (Flat) Wire
(not supplied)
3 Separate VHF and UHF Antennas
Combiner 75/300 ohm Inputs 75 ohm output
UHF
VHF
300 ohm Twin Lead (Flat) Wire
(not supplied)
75 ohm Coaxial Cable
Note:
If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and
one 75 ohm output.
Notes: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to
the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type
antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
14
for details.
POWER button
OPEN/CLOSE button (D D)
"
T / CR button
INPUT SELECT button
"
SLOW button
! ""
MENU button
"'
ENTER button
! ##
RETURN button
##
PLAY button
! "
INDEX+ button
!!
SKIP button
""
FF button
! ""
A-B RPT button
"%
SP/SLP button
!"
PLAYMODE button
"%
CALL button
DISPLAY button
ZERO RETURN button
!
SEARCH button
"#
MARKER button
"$
AUDIO SELECT button
!'
AUDIO button
#
DVD/VCR
IN
(ANT)
OUT
(TV)
DVD/VCR
IN
(ANT)
OUT
(TV)
DVD/VCR
(not supplied)
IN
(ANT)
OUT
(TV)
Inserting batteries
1
Open the battery compart- 2 Install two "AAA" batteries
ment cover in the direction of (supplied), paying attention to the
the arrow. polarity diagram in the battery
compartment.
Caution:
Never throw batteries into a fire.
Notes:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the environment in mind. Always dispose of batteries in accordance with
applicable laws and regulations.
• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries with
new ones.
• When necessary to replace batteries in the remote control, always replace both batteries with new ones. Never mix
battery types or use new and used batteries in combination.
• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from leaking into the battery compartment.
Remote control basics
• Press POWER to turn the DVD/VCR on or off.
• Select your desired operating mode (DVD or VCR) using VCR DVD.
(DVD or VCR indicator on the front panel will show you which mode is selected.)
• Press CH + or CH – to move through the channels one channel at a time.
• The / / / are also used to navigate on-screen menu system.
• You can directly access specific channels using Direct channel selection buttons (0–9).
• Each press of VCR DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the
DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to
operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of approx. 7 meters.
DVD/VCR to TV connection
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the
connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
VHF/UHF IN
75 ohm Coaxial Cable (supplied)
Splitter 75 ohm Input
75/300 ohm outputs
75 ohm Coaxial Cable (not supplied)
(supplied)
Splitter 75 ohm Input
300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
(supplied)
3 Replace the compartment
cover.
Approx. 7 meters
13
TV
Note: If a VHF or UHF antenna is used,
set the TV/CABLE menu option to
the "TV" mode.
TV with single 75 ohm VHF/UHF antenna
input
TV
Note: If a VHF or UHF antenna is used,
set the TV/CABLE menu option
UHF
to the "TV" mode.
VHF
TV with 300 ohm UHF and 75 ohm VHF
antenna inputs
TV
Note: If a VHF or UHF antenna is used,
UHF
set the TV/CABLE menu option to
the "TV" mode.
VHF
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
15