Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for SOYO 82430 TX P54C
Summary of Contents for SOYO 82430 TX P54C
- Page 1 Pentium 82430 TX P54C/P55C PCI Mainboard User’s Guide & Technical Reference 5TT5...
-
Page 2: About This Guide
® ™ About This Guide This UserÕs Guide is for assisting system manufacturers and end users in setting up and installing the mainboard. Information in this guide has been carefully checked for reliability; however, no guarantee is given as to the correctness of the contents. -
Page 3: Table Of Contents
JP43: CPU Cooling Fan Connector........6 CPU Type Configuration ............7 Step 1: Frequency Setting............. 7 Pentium Ð 90/100 CPU Settings (1.5 x clock)....7 Pentium Ð 120/133 CPU Settings (2.0 x clock)....8 PentiumÐ 150/166 CPU Settings (2.5 x clock) ....9 Pentium Ð... - Page 4 J17 Ð Keylock & Power LED Connector ......18 CN2 Ð PS/2 Keyboard Connector ........18 CN1 Ð PS/2 Mouse Connector ..........18 PRT Ð Parallel Port Connector ..........18 J18 Ñ Speaker Connector ........... 18 J22 Ð Turbo LED Connector ..........18 USB1 Ð...
-
Page 5: Chapter 1: Introduction
1 Introduction The 82430 TX PCI mainboard is a high-performance ATX form-factor system board that supports P54C/P55C family CPUs and 512K external cache memory on the mainboard. The mainboard is fully compatible with industry standards, and adds many technical enhancements. Key Features ¥... -
Page 6: Unpacking The Mainboard
Introduction Unpacking the Mainboard The mainboard package contains: ¥ The 82430TX Mainboard ¥ This UserÕs Guide ¥ One IDE Bus Master driver diskette Note: Do not unpack the mainboard until you are ready to install it. Follow the precautions below while unpacking the mainboard. 1. -
Page 7: Mainboard Layout W/ Default Settings
Introduction Mainboard Layout w/ Default Settings Figure 1Ð1. Mainboard Layout 1. ZIF socket 7 (for P54C/P55C) 10. Unbuffered DIMM Bank 2. 82430 TX Chipset 11. Floppy Connector 3. Pipelined Burst SRAM 12. IDE1/IDE2 Connector 4. Ultra I/O Chip 13. Parallel Port Connector 5. - Page 8 Introduction Default settings are as follows: Pentium 133MHz (P54C) CPU, 512K Pipelined Burst cache, On-board PCI E-IDE Enabled, 2 high speed UARTS Enabled (w/ 16550 FIFO), 1 EPP/ECP port (ECP + EPP mode), and 5V DRAM/3.3V DIMM. COM2 COM1 PS/2...
-
Page 9: Chapter 2: Hardware Setup
2 Hardware Setup This chapter explains how to configure the mainboardÕs hardware. After you install the mainboard, you can set jumpers, install memory on the mainboard, and make case connections. Refer to this chapter whenever you upgrade or reconfigure your system. CAUTION: Turn off power to the mainboard, system chassis, and peripheral devices before performing any work on the... -
Page 10: Jp43: Cpu Cooling Fan Connector
Hardware Setup JP43: CPU Cooling Fan Connector This 3-pins connector provides 12V power for the CPU cooling fan which matches the pin assignment of this connector. CPU Cooling Fan Connector (Pin Assignment) 1 (GND) 2 (12V) 3 (GND) Note: Make sure the pin assignment of our CPU Cooling Fan is matched with this connector before connecting it, otherwise, you may damage either the mainboard or the cooling fan. -
Page 11: Cpu Type Configuration
This section shows you how to configure your CPU step by step. Note that you need to check the CPU voltage before installation. Step 1: Frequency Setting Pentium – 90/100 CPU Settings (1.5 x clock) AMD K5 – PR90/PR100/PR120/PR133 (1.5 x clock) Pentium – 90/60 MHz Family AMD K5 –... -
Page 12: Pentium Ð 120/133 Cpu Settings (2.0 X Clock)
Hardware Setup Pentium – 120/133 CPU Settings (2.0 x clock) Cyrix 6x86/6x86L – P133 +/ P150 + /P166 + CPU Settings (2.0 x clock) AMD K5/K6 – PR150 CPU Setting Cyrix 6x86/6x86L – P133 + /55 MHz Family 123456 P.B. SRAM Pentium –... -
Page 13: Pentiumð 150/166 Cpu Settings (2.5 X Clock)
Hardware Setup Pentium– 150/166 CPU Settings (2.5 x clock) AMD K5/K6– PR166 CPU Setting Family Pentium – 150/60 MHz 123456 P.B. SRAM 64Kx32 82439 TX Pentium – 166/66 MHz AMD K5/K6 – PR166 P.B. SRAM 64Kx32 123456 Figure 2Ð1Ð3. CPU Jumper Settings... -
Page 14: Pentium Ð 180/200 Cpu Settings (3.0 X Clock)
Hardware Setup Pentium – 180/200 CPU Settings (3.0 x clock) AMD K6 – PR200 CPU Setting Family Pentium – 180/60 MHz 123456 P.B. SRAM 64Kx32 82439 TX Pentium – 200/66 MHz AMD-K6/PR2-200 P.B. SRAM 64Kx32 123456 Figure 2Ð1Ð4. CPU Jumper Settings... -
Page 15: Pentium Ð 233 Cpu Setting (3.5 X Clock)
Hardware Setup Pentium – 233 CPU Setting (3.5 x clock) AMD K6 – PR233 CPU Setting Family P.B. SRAM 64Kx32 82439 TX P.B. SRAM 64Kx32 Pentium – 233 MHz AMD K6 – PR233 123456 Figure 2Ð1Ð5. CPU Jumper Settings Note: You must equip the CPU with a fan and heat sink for system stability. -
Page 16: Amd K6 Ð Pr266 Cpu Setting (4.0 X Clock)
Hardware Setup AMD K6 – PR266 CPU Setting (4.0 x clock) Family P.B. SRAM 64Kx32 82439 TX P.B. SRAM 64Kx32 AMD K6 – PR266 123456 Figure 2Ð1Ð6. CPU Jumper Settings Note: You must equip the CPU with a fan and heat sink for system stability. -
Page 17: Step 2: Cpu Single/Dual Voltage Setting
Hardware Setup Step 2: CPU Single/Dual Voltage Setting There are two kinds of CPU input voltages due to various designs of CPUsÑsingle voltage and dual voltage. Set your CPU according to the type that you have. Single Voltage CPU Setting Signal voltage CPUs use the same voltage for VIO and VCore and has been used traditionally. -
Page 18: Dual Voltage Cpu Setting
Hardware Setup Dual Voltage CPU Setting Dual voltage CPUs are designed to use different voltage for VIO and VCore and they include Intel P55C series, Cyrix 6x86L, and AMD K6. Refer to the following figures to set these CPUsÕ voltage: 2.8V CPU (default) JP3o... -
Page 19: Memory Configuration Table
Hardware Setup Memory Configuration Table SIMM Bank DIMM Bank Bank 0 Bank 1 DIMM 1 DIMM 2 RAM Type FPM/EDO FPM/EDO FPM/EDO/ FPM/EDO/ (DRAM) (DRAM) SDRAM SDRAM Single 4/8/16/32/64 4/8/16/32/64 8/16/32/64 8/16/32/64 Module Size (MB) Note: Do not install FPM or EDO SIMM/DIMM when you already installed SDRAM type of DIMM. -
Page 20: Multi I/O Port Addresses
Hardware Setup Multi I/O Port Addresses Default settings for multi-I/O port addresses are shown in the table below. Port I/O Address Status LPT1* 378H ECP + EPP COM1 3F8H COM2 2F8H * If default I/O port addresses conflict with other I/O cards (e.g. sound cards or I/O cards), you must adjust one of the I/O addresses to avoid address conflict. -
Page 21: Atx Pw Ñ Atx Power Supply Connectors
Hardware Setup ATX PW — ATX Power Supply Connectors The motherboard provides an ATX power supply connector. It is a twenty-pin male header connector. Plug the connector from the power directly onto the board connector while making sure the pin1 is in its position. -
Page 22: J24 Ð Hdd Led Connectors
Hardware Setup J24 – HDD LED Connectors Attach the cable of hard disk drive LEDs to this connector. The LED lights when an HDD is active. IDE1/IDE2 – On-board Primary/Secondary IDE HDD Connectors Attach cables of hard disk drives to these connectors. IR1 –... -
Page 23: Chapter 3: Bios Setup
3 BIOS Setup The mainboardÕs BIOS setup program is the ROM PCI/ISA BIOS from Award Software Inc. Enter the Award BIOS programÕs Main Menu as follows: 1. Turn on or reboot the system. After a series of diagnostic checks, you are asked to press DEL to enter Setup. 2. -
Page 24: Standard Cmos Setup
BIOS Setup Standard CMOS Setup Run the Standard CMOS Setup as follows. 1. Choose ÒSTANDARD CMOS SETUPÓ from the Main Menu. A screen appears. ROM PCI/ISA BIOS STANDARD CMOS SETUP AWARD SOFTWARE, INC. Date (mm:dd:yy) : Fri, Feb 1 1995 Time (hh:mm:ss) : 7 : 30 : 33 HARD DISKS... - Page 25 BIOS Setup Primary Large Ð Large IDE hard disk (for certain (Secondary) hard disk) Master & Slave Note: If you have any questions on your hard (Continued) disk type or mode, ask your hard disk provider or previous user for details. Drive A &...
-
Page 26: Bios Features Setup
BIOS Setup BIOS Features Setup Run the BIOS Features Setup as follows. 1. Choose ÒBIOS FEATURES SETUPÓ from the Main Menu and a screen with a list of items appears. (The screen below shows the BIOS default settings.) ROM PCI/ISA BIOS BIOS FEATURES SETUP AWARD SOFTWARE, INC. -
Page 27: Bios Setup
BIOS Setup Boot Sequence Choose the boot device sequence as your need. For example, ÒA, C, SCSIÓ means BIOS will look for an operating system first from drive A, drive C, then SCSI device. Options of this function are: A, C, SCSI C, A, SCSI C, CDÐROM, A CDÐROM, C, A... - Page 28 BIOS Setup PCI/VGA Enabled: The color of the monitor may be incorrect Palette Snoop if uses with MPEG card. Enable this option to make the monitor normal. Disabled: Disable Snoop function (default). OS Select for OS2 Ð Choosing this when you are using OS/2 DRAM >64MB operation system.
-
Page 29: Chipset Features Setup
BIOS Setup Chipset Features Setup The Chipset Features Setup option changes the values of the chipset registers. These registers control system options in the computer. Note: Change these settings only if you are familiar with the Chipset. Run the Chipset Features Setup as follows. 1. - Page 30 BIOS Setup DRAM Read Burst Use the default setting. (EDO/FP) DRAM Write Burst Use the default setting. Timing Fast EDO Lead Off Use the default setting. Refresh RAS# Assertion Use the default setting. Fast RAS to CAS Delay Use the default setting. DRAM Page Idle Timer Use the default setting.
-
Page 31: Power Management Setup
BIOS Setup Memory Hole At 15M- Choose Enabled or Disabled (default). Some interface cards will map their ROM address to this area. If this occurs, you should select Enabled, otherwise use Disabled. 3. After you have finished with the Chipset Features Setup, press the <ESC>... - Page 32 BIOS Setup A short description of selected screen items follows: Power Management Options are as follows: User Define Ð LetÕs you define the HDD and system power down times (default). Disable Ð Disables the Green PC Features. Min Saving Ð Doze timer = 1 Hour Standby timer = 1 Hour Suspend timer = 1 Hour HDD Power Down = 15 Min...
- Page 33 BIOS Setup HDD Power Down When the set time has elapsed, the BIOS sends a command to the HDD to power down, which turns off the motor. Time is adjustable from 1 to 15 minutes. The default setting is Disabled. Some older model HDDs may not support this advanced function.
-
Page 34: Pnp/Pci Configuration Setup
BIOS Setup Primary/Secondary Choose Enabled or Disabled (default). IDE 0 Enabled Ð Enables the power management Primary/Secondary timers when Òno activityÓ event is IDE 1 detected. Choose Enabled or Disabled. Floppy Disk/ Serial Port/ Enabled Ð enables the power management Parallel Port timers when Òno activityÓ... - Page 35 BIOS Setup A short description of screen items follows: Resources Manual Ð BIOS doesnÕt manage PCI/ISA PnP Controlled By card (i.e., IRQ) automatically. Auto Ð BIOS auto manage PCI and ISA PnP card (recommended). Reset Disabled Ð Retain PnP configuration data in Configuration BIOS.
-
Page 36: Load Setup Defaults
BIOS Setup Load Setup Defaults This item loads the system values you have previously saved. Choose this item and the following message appears: ÒLoad SETUP Defaults (Y/N)? NÓ To use the SETUP defaults, change the prompt to ÒYÓ and press <Enter>. -
Page 37: Integrated Peripherals
BIOS Setup Integrated Peripherals The Integrated Peripherals option changes the values of the chipset registers. These registers control system options in the computer. Note: Change these settings only if you are familiar with the Chipset. Run the Integrated Peripherals as follows. 1. - Page 38 BIOS Setup IDE Primary Master Choose Auto (default) or Disabled. UDMA/ Auto Ð Supports Ultra DMA mode. IDE Primary Slave UDMA/ IDE Secondary Master UDMA/ IDE Secondary Slave UDMA On-chip Primary PCI Enabled Ð Use the on-board IDE IDE/ (default) On-chip Secondary PCI Disabled Ð...
- Page 39 BIOS Setup IR Transmission Delay Choose Enabled (default) or Disabled. Due to the various design of IR devices, transmission delay has to be added on for different protocol. IR IRQ Select Choose IRQ3, IRQ4 (default), IRQ10, or IRQ11. If you have IRQ conflict problem during using the IR device, select another IRQ then try again.
-
Page 40: Supervisor Password
BIOS Setup Supervisor Password Based on the setting you made in the ÒSecurity OptionÓ of the ÒBIOS FEATURES SETUPÓ, this Main Menu item lets you configure the system so that a password is required every time the system boots or an attempt is made to enter the Setup program. -
Page 41: User Password
BIOS Setup User Password Based on the setting you made in the ÒSecurity OptionÓ of the ÒBIOS FEATURES SETUPÓ, this Main Menu item lets you configure the system so that a password is required every time the system boots or an attempt is made to enter the Setup program. -
Page 42: Ide Hdd Auto Detection
BIOS Setup IDE HDD Auto Detection This Main Menu item automatically detects the hard disk type and configures the STANDARD CMOS SETUP accordingly. This function is only valid for IDE hard disks. Note: ROM PCI/ISA BIOS CMOS SETUP UTILITY AWARD SOFTWARE, INC. HARD DISKS TYPE SIZE... -
Page 43: Chapter 4: Drivers Installation Guide
4 Drivers Installation Guide IDE BUS Master Installation Guide MS-DOS/WINDOW/WFW 1) You should install CD-ROM in secondary channel in Windows (WFW). 2) Change the current directory to a: or b:. 3) Under DOS command line prompt, run the SETUP directly. After entering the setup utility, just follow the instructions of the setup. -
Page 44: Windows 95
Drivers Installation Guide WINDOWS 95 1) Close any running applications. 2) Insert the floppy disk into drive A:. 3) Open ÒMy ComputerÓ, double click ÒDrive A:Ó. 4) Double click ÒWin95Ó. 5) Double click the Setup program. 6) Then just follow the instruction. NOVELL 3.X&4.X 1) Copy the driver TRIN4X.DSK or TRIN312.DSK to the subdirectory which holds the file SERVER.EXE. -
Page 45: Sco Unix 5.0
Drivers Installation Guide 5) Now, insert a blank diskette into the floppy drive A and type: tar cvf /dev/<your floppy drive A device name>. (Note: there is a period at the end of the last command.) Your floppy drive A device name could be: ¥... -
Page 46: Os/2 2.0 And Warp 3.X
Drivers Installation Guide OS/2 2.0 and WARP 3.X 1) Copy TRIOS2.ADD from the floppy diskette to your hard disk under the OS2 directory (i.e., C:\OS2). 2) Edit C:\CONFIG.SYS to replace BASEDEV=IBM1S506.ADD with BASEDEV=TRIOS2.ADD 3) Reboot the system. Note: For more information (like parameter settings, driver de- installation, etc.), please refer to the README.TXT file on the diskette.