1. Manuals
  2. Brands
  3. Zte Manuals
  4. Switch
  5. ZXR10 8900 Series
  6. Command reference manual

Zte ZXR10 8900 Series Command Reference Manual

10 gigabit routing switch
Hide thumbs Also See for ZXR10 8900 Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Command Manual, Command Reference Manual
ZXR10 8900 Series
10 Gigabit Routing Switch
Command Reference (Multicast)
Version 2.8.02.C
ZTE CORPORATION
ZTE Plaza, Keji Road South,
Hi-Tech Industrial Park,
Nanshan District, Shenzhen,
P. R. China
518057
Tel: (86) 755 26771900
Fax: (86) 755 26770801
URL: http://ensupport.zte.com.cn
E-mail: support@zte.com.cn

Advertisement

Table of Contents
loading

Related Manuals for Zte ZXR10 8900 Series

Summary of Contents for Zte ZXR10 8900 Series

  • Page 1 ZXR10 8900 Series 10 Gigabit Routing Switch Command Reference (Multicast) Version 2.8.02.C ZTE CORPORATION ZTE Plaza, Keji Road South, Hi-Tech Industrial Park, Nanshan District, Shenzhen, P. R. China 518057 Tel: (86) 755 26771900 Fax: (86) 755 26770801 URL: http://ensupport.zte.com.cn E-mail: support@zte.com.cn...
  • Page 2 The contents of this document are protected by copyright laws and international treaties. Any reproduction or distribution of this document or any portion of this document, in any form by any means, without the prior written consent of ZTE CORPO- RATION is prohibited.

  • Page 3: Table Of Contents

    About This Manual..........i Command Introduction ........1 Manual Instruction............1 Description of Man-Machine Commands ......1 Auxiliary Function ............2 Command Modes............3 IGMP Protocol ...........9 clear ip igmp groups ............9 clear ip igmp packet-count..........10 ip igmp access-group .............10 ip igmp immediate-leave ..........10 ip igmp last-member-query-interval .........11 ip igmp querier-timeout..........11...
  • Page 4 router pimsm ..............25 rp-candidate ..............26 ssm range ..............27 show ip forwarding mroute ..........27 show ip mforwarding............28 show ip mroute .............29 show ip mroute summary ..........30 show ip pim bsr.............31 show ip pim rp mapping ..........31 show ip pim rp hash............32 show ip pimsm interface..........33 show ip pimsm mroute ...........33 show ip pimsm neighbor..........35...
  • Page 5 show ip msdp count ............51 show ip msdp peer ............52 show ip msdp sa-cache ..........53 show ip msdp summary..........54 IGMP SNOOPING ..........55 igmp snooping ..............56 igmp snooping acl ............56 igmp snooping drop ............56 igmp snooping fast-leave..........57 igmp snooping host-time-out ..........57 igmp snooping last-member-query-interval .......58 igmp snooping max-group-num........58 igmp snooping max-host-in-group ........58...
  • Page 6 show ip igmp snooping ssm-mapping .......70 show ip igmp snooping statistic ........70 show ip igmp snooping vlan ..........71 PIM SNOOPING ..........73 ip pim snooping.............73 pim snooping ..............73 show ip pim snooping all-statistic ........74 show ip pim snooping all-statistic clear ......74 show ip pim snooping entry ..........74 show ip pim snooping neighbor-info .........75 show ip pim snooping port-info........75...

  • Page 7: About This Manual

    About This Manual ZXR10 8900 Series (V2.8.02.C) 10G Routing Switch Command About this Manual Reference (Multicast). ZXR10 8900 Series (V2.8.02.C) 10G Rout- ing Switch Command Reference has 16 volumes. The details are as follows: Summary Manual Name ZXR10 8900 Series (V2.8.02.C)
  • Page 8 ZXR10 8900 Series Command Reference (Multicast) Manual Name Summary ZXR10 8900 Series (V2.8.02.C) This manual describes interface 10G Routing Switch Command configuration, DHCP and Reference (Basic Configuration VRRP-related commands in Volume II) ZXR10 8900 series 10G routing switch. ZXR10 8900 Series (V2.8.02.C)
  • Page 9 Chapter 7 PIM This chapter describes the configuration of PIM SNOOPING SNOOPING and command to view it. Chapter 8 MLD This chapter describes the configuration of MLD SNOOPING SNOOPING and command to view it. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 10 ZXR10 8900 Series Command Reference (Multicast) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 11: Command Introduction

    Reference includes 16 volumes. For details of each volume, please refer to preface of this manual. Commands in ZXR10 8900 Series (V2.8.02.C) 10G Routing Switch Command Reference (Index) are listed in sequence of from letter a to letter z and in form of table. Commands of all other volumes are classified and illustrated according to different function modules.

  • Page 12: Auxiliary Function

    ZXR10 8900 Series Command Reference (Multicast) � Command format It describes the complete format of this command. If no for- mat is available, list it. � Parameter Description It describes parameters in this command in the form and pre- scribes the range and default value. If different products have different parameter ranges or default values, an additional form is used for description.

  • Page 13: Command Modes

    Use show history command in any mode, and the latest sev- eral commands in this mode will be listed. Command Modes The command modes in this manual are as follows: Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 14 ZXR10 8900 Series Command Reference (Multicast) Modes Prompt Admis- Command Function sion to Enter the Mode Mode User ZXR10> Enter this View simple Mode mode directly information after logging onto system Privi- User enable Configure ZXR10# leged Mode system mode...
  • Page 15 OSPF protocol parameters router isis Configure IS-IS protocol parameters router bgp Configure BGP protocol parameters router Configure pimsm PIM-SM protocol parameters ipv6 router It configures RIPng parameters. ipv6 router It configures ospf OSPFv3 parameters. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 16 ZXR10 8900 Series Command Reference (Multicast) Modes Prompt Admis- Command Function sion to Enter the Mode Mode ZXR10(config- Global ip vrf Configure Config- vrf)# config- VRF protocol uration uration parameters Mode mode VFI con- ZXR10(config- Global It configures figu- vfi)#...
  • Page 17 Mode Mode IPSec ZXR10(config- Global ipsec It configures config- ipsec)# config- IPv6 IPSec uration uration protection. mode mode Diagno- Privi- diagnose It tests CPU ZXR10(diag)# sis mode leged utilization mode and memory utilization. Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 18 ZXR10 8900 Series Command Reference (Multicast) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 19: Igmp Protocol

    If there is no parameter after this command, all dynamically added Instructions multicast groups are deleted. If there is the <interface-name> parameter after this command, all dynamically added multicast groups on the specified interface are deleted. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 20: Clear Ip Igmp Packet-Count

    ZXR10 8900 Series Command Reference (Multicast) show ip igmp groups Related Commands clear ip igmp packet-count Use this command to clear the statistics count of IGMP re- Purpose ceived/sent messages. Privileged EXEC Command Modes clear ip igmp packet-count Syntax show ip igmp packet-count...

  • Page 21: Ip Igmp Last-Member-Query-Interval

    <seconds> Syntax no ip igmp querier-timeout Syntax Description <seconds> Number of seconds that the router waits after the previous querier has stopped querying and before it takes over as the querier, range: 60~300 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 22: Ip Igmp Query-Interval

    ZXR10 8900 Series Command Reference (Multicast) The default timeout period equals to (query-interval×2 1) in sec- Defaults onds. ip igmp query-interval Related Commands ip igmp query-interval Use this command to configure the frequency at which IGMP host Purpose query messages are sent. Restore default with the no form of this command.

  • Page 23: Ip Igmp Static-Group

    All IGMP routers and hosts on the subnet must support the same Instructions version. Considering the safety of the multicast network, IGMP Version 1 automatic detection and negotiation are not supported. ip igmp query-max-response-time Related Commands show ip igmp interface Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 24: Ip Igmp Ssm-Map Static

    ZXR10 8900 Series Command Reference (Multicast) ip igmp ssm-map static Use this command to configure source address mapped by PIM- Purpose SSM multicast group. Use the no command to delete source ad- dress mapped by PIM-SSM multicast group. Global Configuration Mode...

  • Page 25: Show Ip Igmp Groups Summary

    Internet Group Manage- ment Protocol (IGMP). ZXR10#show ip igmp groups summary IGMP groups summary: Interface Static Joined Total fei_1/1 fei_1/3 Summary Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 26: Show Ip Igmp Interface

    ZXR10 8900 Series Command Reference (Multicast) ip igmp static-group Related Commands show ip igmp groups show ip igmp interface Use this command to display multicast-related information about Purpose an interface. All modes except user EXEC Command Modes show ip igmp interface [<interface-name>]...

  • Page 27: Show Ip Igmp Ssm-Mapping

    <group addr> Syntax Syntax Description Parameter Description <group addr> Multicast group address, in dotted decimal notation. View the mapping information from multicast group 232.1.2.3 to Example source. ZXR10（config）# show ip igmp ssm-mapping 232.1.2.3 Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 28 ZXR10 8900 Series Command Reference (Multicast) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 29: Pim-Sm Protocol

    Use this command to filter the multicast messages encapsulated Purpose in the received register messages. Remove the filtering with the no form of this command. Router configuration Command Modes accept-register <access-list-number> Syntax Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 30: Accept-Rp

    ZXR10 8900 Series Command Reference (Multicast) no accept-register Syntax Description <access-list-number> Standard IP access list number, range: 1~99 The multicast messages encapsulated in the register messages are Defaults not filtered by default. Source addresses of the multicast messages encapsulated in the...

  • Page 31: Clear Ip Mroute

    If the group option is used, the (*, g) and all related (s, g) multicast route entries will be deleted. � If the group and source address options are used, the related (s, g) multicast route entries will be deleted. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 32: Ip Multicast-Loadshare

    ZXR10 8900 Series Command Reference (Multicast) show ip mroute Related Commands ip multicast-loadshare This command is used to enable L3 multicast load sharing function. Command Function Global configuration mode Command Modes ip multicast-loadshare Command format no ip multicast-loadshare ip multicast-routing...

  • Page 33: Ip Pim Dr-Priority

    Syntax no ip pim neighbor-filter Syntax Description <access-list-number> Number or name of a standard IP access list that denies PIM packets from a source, range: 1~99 This command is disabled by default. Defaults Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 34: Ip Pim Query-Interval

    ZXR10 8900 Series Command Reference (Multicast) This example describes how to prevent the router defined by ACL Example 10 from participating in Protocol Independent Multicast (PIM) on the interface fei_1/1. ZXR10(config)#access-list 10 deny 10.1.1.1 0.0.0.0 ZXR10(config)#interface fei_1/1 ZXR10(config-if)#ip pim neighbor-filter 10...

  • Page 35: Packet-Count

    Related Commands router pimsm Use this command to enable IP multicast protocol PIM-SM. Disable Purpose PIM-SM with the no form of this command. Global configuration Command Modes router pimsm Syntax Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 36: Rp-Candidate

    ZXR10 8900 Series Command Reference (Multicast) no router pimsm If the ip multicast-routing command is not configured, the Instructions PIM-SM routing protocol does not run. ip multicast-routing Related Commands rp-candidate Use this command to configure the router to advertise itself to...

  • Page 37: Ssm Range

    1. If there is no source address option after this command, the (*, Instructions g) multicast forwarding entries are displayed. If there is the source address option after this command, the (s, g) multicast forwarding entries are displayed. 2. Description of the displayed information: Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 38: Show Ip Mforwarding

    ZXR10 8900 Series Command Reference (Multicast) Field Description Up Send Sends multicast packets upward to this entry Assert flag Assert flag of the error interface receiving multicast packets No Used The entry is not used IIF MATCH Multicast packets are matched on the...

  • Page 39: Show Ip Mroute

    Outgoing interface of the route entry is null RP-bit set This (S, g) entry exists on the shared tree Register flag Indicates the entry can send register messages of the directly connected source Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 40: Show Ip Mroute Summary

    ZXR10 8900 Series Command Reference (Multicast) Field Description SPT-bit set Indicates this route entry receives multicast packets from SPT tree Up Send Sends multicast packets upward to this entry No Used The entry is not used Join SPT Data flow switches to the SPT tree...

  • Page 41: Show Ip Pim Bsr

    Use this command to display information about rendezvous points Purpose (RPs) advertised by the bootstrap router (BSR). All modes Command Modes show ip pim rp mapping Syntax Description of the displayed information: Instructions Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 42: Show Ip Pim Rp Hash

    ZXR10 8900 Series Command Reference (Multicast) Field Description Group Address and mask of the multicast group advertised by the BSR Rp address Candidate RP address advertised by the multicast group Static Indicates this candidate RP is not advertised by the BSR but locally statically configured...

  • Page 43: Show Ip Pimsm Interface

    Use this command to show the content of the PIM-SM multicast Purpose routing table. All modes Command Modes show ip pimsm mroute [[group <group-address>[source Syntax <source-address>]]|[source <source-address>]|[summary]] Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 44 ZXR10 8900 Series Command Reference (Multicast) Syntax Description group <group-addre Multicast group address in the dotted decimal ss> format source <source-addr Source address in the dotted decimal format ess> summary Summary display � If there is no option after this command, all multicast route Instructions tables are displayed.

  • Page 45: Show Ip Pimsm Neighbor

    Syntax Syntax Description <interface-number> Interface ID, in the form of board name/interface number If a subinterface exists, it can be board name/interface number/subinterface number Description of the displayed information is as follows: Instructions Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 46: Show Ip Route Multicast

    ZXR10 8900 Series Command Reference (Multicast) Field Description DataUpsend Number of upward sent packets received Packet-type Type of packets received on the interface Rx_ok Statistics of correct packets received on the interface Tx_ok Statistics of correct packets transmitted on the interface...

  • Page 47: Spt-Threshold

    Instructions participate the selection, even if this router does not receive any advertisement of RP information of BSR . 2. If no <access-list-number> is specified, the static RP applies for all multicast groups. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 48: Static-Rp Override

    ZXR10 8900 Series Command Reference (Multicast) This example describes how to configure the address 10.1.1.1 as Example the static RP address to serve all multicast groups. ZXR10(config-router)#static-rp 10.1.1.1 show ip pim rp mapping Related Commands static-rp override This command is used to apply static RP for the same RP priorities.

  • Page 49: Pim-Dm Protocol

    If the ip multicast-routing command is not configured, the Instructions PIM-DM routing protocol can not be enabled. If PIM-SM rout- ing protocol is configured, PIM-DM routing protocol can not be enabled either. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 50: Show Ip Pimdm Interface

    ZXR10 8900 Series Command Reference (Multicast) ip multicast-routing Related Commands show ip pimdm interface Use this command to show the interface on which PIM-DM is con- Purpose figured. All modes Command Modes show ip pimdm interface [<interface-name>] Syntax Syntax Description <interface-name>...

  • Page 51: Show Ip Pimdm Neighbor

    Use this command to show neighbors of the interface on which Purpose PIM-DM is enabled. All modes Command Modes show ip pimdm neighbor [<interface-name>] Syntax Syntax Description <interface-name> Interface name Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 52 ZXR10 8900 Series Command Reference (Multicast) 1. To show the neighbors of the specified interface on which Instructions PIM-DM is enbled, use the <interface-name> option after this command. 2. Description of the displayed fields of the PIM-DM neighbor is as follows:...

  • Page 53: Msdp Protocol

    MSDP peer. This example describes how to clear the TCP connection of Example the specified Multicast Source Discovery Protocol (MSDP) peer 101.1.1.1. ZXR10#clear ip msdp peer 101.1.1.1 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 54: Clear Ip Msdp Sa-Cache

    ZXR10 8900 Series Command Reference (Multicast) ip msdp peer Related Commands clear ip msdp sa-cache Use this command to clear Multicast Source Discovery Protocol Purpose (MSDP) source-active (SA) cache entries. Privileged EXEC Command Modes clear ip msdp sa-cache [<group-address>] Syntax...

  • Page 55: Ip Msdp Description

    Use this command to add descriptive text to the configuration for Purpose a Multicast Source Discovery Protocol (MSDP) peer. Remove the description with the no form of this command. Global configuration Command Modes ip msdp description <peer-address><desc-text> Syntax no ip msdp description <peer-address> Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 56: Ip Msdp Mesh-Group

    Defaults This description is visible in the show ip msdp peer command Instructions output. This example describes how to add the description “zte-route A” Example for the peer at the IP address 101.1.1.1. ZXR10(config)#ip msdp description 101.1.1.1 zte-route A show ip msdp peer...

  • Page 57: Ip Msdp Originator-Id

    MSDP configuration mode. This example describes how to configure the router at the IP ad- Example dress 101.1.1.1 as the MSDP peer of this router. ZXR10(config)#ip msdp peer 101.1.1.1 connect-source loopback1 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 58: Ip Msdp Redistribute

    ZXR10 8900 Series Command Reference (Multicast) ip msdp default-peer Related Commands ip msdp redistribute Use this command to configure which (S, G) entries from the multi- Purpose cast routing table are advertised in Source-Active (SA) messages originated to Multicast Source Discovery Protocol (MSDP) peers.

  • Page 59: Ip Msdp Sa-Filter Out

    ACL 100 to be forwarded to the MSDP peer 101.1.1.1. ZXR10(config)#ip access-list extended 100 ZXR10(config-ext-nacl)#permit ip 103.3.0.0 0.0.255.255 224.1.0.0 0.0.255.255 ZXR10(config)#ip msdp peer 101.1.1.1 connect-source loopback1 ZXR10(config)#ip msdp sa-filter out 101.1.1.1 list 100 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 60: Ip Msdp Sa-Limit

    ZXR10 8900 Series Command Reference (Multicast) ip msdp peer Related Commands ip msdp sa-fitler in ip msdp sa-limit Use this command to limit the number of Source-Active (SA) mes- Purpose sages from a Multicast Source Discovery Protocol (MSDP) peer that the router will allow in the SA cache.

  • Page 61: Ip Msdp Ttl-Threshold

    Syntax The following is sample output of the show ip msdp count com- Example mand: ZXB10#show ip msdp count SA State per Peer Counters, <Peer><# SA learned> 101.1.1.1: 2 102.2.2.2: 20 103.3.3.3: 10 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 62: Show Ip Msdp Peer

    ZXR10 8900 Series Command Reference (Multicast) Total entries: 32 Description of the displayed information is as follows: Field Description 101.1.1.1: 2 MSDP peer with IP address 101.1.1.1: 2 SA messages from the MSDP peer in the SA cache Total entries:32...

  • Page 63: Show Ip Msdp Sa-Cache

    00:21:45/ 00:05:57 Local route has been cached for 21 minutes and 45 seconds. If no SA message is received in 5 minutes and 57 seconds, the route will be removed from the SA cache Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 64: Show Ip Msdp Summary

    ZXR10 8900 Series Command Reference (Multicast) clear ip msdp sa-cache Related Commands show ip msdp summary Use this command to display Multicast Source Discovery Protocol Purpose (MSDP) peer status. All modes Command Modes show ip msdp summary Syntax The following is sample output of the show ip msdp summary Example command.

  • Page 65: Igmp Snooping

    ..........69 show ip igmp snooping query ..........70 show ip igmp snooping ssm-mapping ........70 show ip igmp snooping statistic ...........70 show ip igmp snooping vlan ..........71 Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 66: Igmp Snooping

    ZXR10 8900 Series Command Reference (Multicast) igmp snooping Use this command to enable IGMP SNOOPING in VLAN configu- Purpose ration mode. Disable IGMP SNOOPING with the no form of this command. VLAN configuration Command Modes igmp snooping Syntax no igmp snooping IGMP SNOOPING is enabled by default.

  • Page 67: Igmp Snooping Fast-Leave

    Restore default with the no form of this command. VLAN configuration Command Modes igmp snooping host-time-out <time> Syntax no igmp snooping host-time-out Syntax Description <time> Aging time of the user in seconds, range: 30~65535, default: 260 seconds Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 68: Igmp Snooping Last-Member-Query-Interval

    ZXR10 8900 Series Command Reference (Multicast) igmp snooping mrouter-time-out Related Commands igmp snooping last-member-query-interval Use this command to configure the last member query interval. Purpose Restore default with the no form of this command. VLAN configuration Command Modes igmp snooping last-member-query-interval <interval>...

  • Page 69: Igmp Snooping Mode

    Delete the setting with the no form of this command. VLAN configuration Command Modes igmp snooping mrouter interface <port-name>[version <1-3 Syntax >][{master <1-99>}{slave <1-99>}] no igmp snooping mrouter interface <port-name> Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 70: Igmp Snooping Mrouter-Time-Out

    ZXR10 8900 Series Command Reference (Multicast) Syntax Description Port name interface <port-na me> version <1-3> Configured route interface version master <1-99> Master ACL number of route interface slave<1-99> Slave ACL number of route interface The interface configured by this command is not aging. Config- Instructions ure acl rule before configuring route interface master/slave acl.

  • Page 71: Igmp Snooping Proxy-Ip

    VLAN configuration Command Modes igmp snooping querier Syntax no igmp snooping querier The proxy querier is disabled by default. Defaults This command takes no effect if the layer 3 multicast routing is Instructions set. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 72: Igmp Snooping Static

    ZXR10 8900 Series Command Reference (Multicast) This command is supported after the platform version 4.6.02. ip igmp snooping query-interval Related Commands ip igmp snooping query-response-interval ip igmp snooping proxy ip igmp snooping querier igmp snooping static Use this command to set static user in VLAN. This user will not be Purpose aging.

  • Page 73: Ip Igmp Snooping Ssm-Mapping

    Related Commands ip igmp snooping Use this command to enable the IGMP SNOOPING function. Dis- Purpose able the IGMP SNOOPING function with the no command. Global configuration Command Modes ip igmp snooping Syntax Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 74: Ip Igmp Snooping Mode

    ZXR10 8900 Series Command Reference (Multicast) no ip igmp snooping The IGMP SNOOPING function is disabled. Defaults To enable global IGMP SNOOPING and to enable MLD SNOOPING Instructions are exclusive. If enabling IGMP SNOOPING in global congfigura- tion, MLD SNOOPING is forbidden; or if enabling MLD SNOOPING in global congfiguration, IGMP SNOOPINGis forbidden.

  • Page 75: Ip Igmp Snooping Querier

    Syntax Description <interval> Query interval (frequency for sending query packets), in seconds, range: 30~65535, default: 125 seconds This command takes effect only when the proxy querier is enabled. Instructions Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 76: Ip Igmp Snooping Query-Response-Interval

    ZXR10 8900 Series Command Reference (Multicast) ip igmp snooping querier Related Commands ip igmp snooping query-response-interval ip igmp snooping query-response-interval Use this command to set the maximum query response interval of Purpose the proxy querier. Restore default with the no form of this com- mand.

  • Page 77: Multicast-Limit

    <ip-address> vlan <vlan-id> Syntax Syntax Description <ip-address> Group IP address, in the form of dotted decimal <vlan-id> VLAN ID, range: 1~4094 This command is supported after the platform version 4.6.02. Instructions Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 78: Show Ip Igmp Snooping Group-Source-Filter Vlan

    ZXR10 8900 Series Command Reference (Multicast) igmp snooping drop Related Commands igmp snooping max-group-num show ip igmp snooping group-source-filter vlan This command is used to show source filtering information of a Command Function group. All modes except user mode Command Modes show ip igmp snooping group-source-filter vlan <vlan-id>...

  • Page 79: Show Ip Igmp Snooping Iptv Port-Info

    Use this command to show information about VLAN interfaces re- Purpose lated to IGMP SNOOPING. All modes except use EXEC Command Modes show ip igmp snooping port-info vlan <vlan-id> Syntax Syntax Description VLAN ID, range: 1~4094 <vlan-id> Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 80: Show Ip Igmp Snooping Query

    ZXR10 8900 Series Command Reference (Multicast) show ip igmp snooping vlan Related Commands show ip igmp snooping query Use this command to show query information about IGMP SNOOP- Purpose ING. All modes except user EXEC Command Modes show ip igmp snooping query...

  • Page 81: Show Ip Igmp Snooping Vlan

    IGMP SNOOPING of the designated VLAN. All modes except user EXEC Command Modes show ip igmp snooping vlan <vlan-id> Syntax Syntax Description <vlan-id> VLAN ID, range: 1~4094 show ip igmp snooping port-info Related Commands Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 82 ZXR10 8900 Series Command Reference (Multicast) This page is intentionally blank. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 83: Pim Snooping

    Command Modes pim snooping Syntax no pim snooping � This command is supported after the platform version 4.6.02. Instructions � This command takes effect only when the global mode is set to SNOOPING. Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 84: Show Ip Pim Snooping All-Statistic

    ZXR10 8900 Series Command Reference (Multicast) ip pim snooping Related Commands show ip pim snooping all-statistic Use this command to show statistics information about all PIM Purpose packets (accumulated statistics). All modes except user EXEC Command Modes show ip pim snooping all-statistic Syntax This command is supported after the platform version 4.6.02.

  • Page 85: Show Ip Pim Snooping Neighbor-Info

    <vlan-id> Syntax Syntax Description <vlan-id> VLAN ID, range: 1~4094 This command is supported after the platform version 4.6.02. Instructions show ip pim snooping entry Related Commands show ip pim snooping neighbor-info Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 86: Show Ip Pim Snooping Port-Statistic Clear Interface

    ZXR10 8900 Series Command Reference (Multicast) show ip pim snooping port-statistic clear interface Use this command to show statistics information of all PIM packets Purpose received by a port (statistics after clear). All modes except user EXEC Command Modes show ip pim snooping port-statistic clear interface <interfa Syntax ce-name>...

  • Page 87: Mld Snooping

    MLD SNOOPING function is enabled with no users and the group is set to DROP mode. Broadcasts multicast packets with the no command. VLAN configuration Command Modes mld snooping drop <ip-address>[num <num>] Syntax no mld snooping drop <ip-address>[num <num>] Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 88: Mld Snooping Fast-Leave

    ZXR10 8900 Series Command Reference (Multicast) Syntax Description <ip-address> IPv6 multicast address <num> The serial ip-address number to drop Multicast packets. Defaults This command only takes effect when MLD SNOOPING function is Instructions enabled. This example shows how to set three serial groups(ff1e::1 ff1e:: Example 2ff1e::3) in VLAN1 to DROP mode.

  • Page 89: Mld Snooping Last-Member-Query-Interval

    VLAN. Restore default with the no command. VLAN configuration Command Modes mld snooping max-group-num <number> Syntax no mld snooping max-group-num Syntax Description <number> The maximum groups pemitted to access: 1~256, 256 by default Confidential and Proprietary Information of ZTE CORPORATION...

  • Page 90: Mld Snooping Max-Host-In-Group

    ZXR10 8900 Series Command Reference (Multicast) mld snooping mrouter-time-out Related Commands mld snooping max-host-in-g roup Use this command to set maximum host number in group. Cancel Purpose the configuration with the no command. VLAN configuration Command Modes mld snooping max-host-in-group <ip-address>[limit-num Syntax <num>]...

  • Page 91: Mld Snooping Mrouter-Time-Out

    Use this command to set MLD SNOOPING proxy query function. Purpose If there is no multicast router in the network, the proxy multicast Confidential and Proprietary Information of ZTE CORPORATION...
  • Page 92 ZXR10 8900 Series Command Reference (Multicast) router sends MLD query packets. Cancel the configuration with the no command. VLAN configuration Command Modes mld snooping static <ip-address> interface <port-name> Syntax no mld snooping static <ip-address> interface <port-name> Syntax Description interface <port-na IPv6 multicast address me>...

Table of Contents