Panasonic KX-FLB758RU Service Manual page 72

KX-FLB758RU
6.2.3. SERVICE FUNCTION TABLE
Code
501 Pause time set
502 Flash time
503 Dial speed select
520 CED frequency select
521 International mode select
522 Auto standby select
523 Receive equalizer select
524 Transmission equalizer select
527 V8 Mode
529 Memory clear for Call Service
550 Memory clear: To reset the value to the default one, except the top margin
(#853),left margin (#854),time/day (#001),logo (#002),Fax No.(#003),History
and Directory.
551 ROM check
552 DTMF signal tone test
553 Monitor on FAX communication
select
554 Modem test
556 Motor test
557 LED test
558 LCD test
561 KEY test
570 BREAK % select
573 Remote turn-on ring number set
590 FAX auto redial time set
591 FAX auto redial time disconnection
time set
592 CNG transmit select
593 Time between CED and 300bps
594 Overseas DIS detection select
595 Receive error limit value set
596 Transmit level set
598 Receiving sensitivity
599 ECM frame size
651 Write system program into the Flash Rom with a parallel cable.
655 Call service 3 detection number
Function Set Value
X 100 msec
X 10 ms
1:10pps
2:20pps
1:2100 Hz
2:1100 Hz
1:ON 2:OFF
1:ON 2:OFF
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1: 0 km
2: 1.8 km
3: 3.6 km
4: 7.2 km
1:DISABLE
2:ENABLE
1:ON 2:OFF
1:OFF
2:PHASE B
3:ALL
1:61% 2:67%
X number of
rings
X number of
times
X second
1:OFF
2:ALL
3:AUTO
1:75 msec
2:500 msec
3:1 sec
1:detects at
the 1st time
2:detects at
the 2nd time
1: 5%
2: 10%
3: 15%
4: 20%
X dBm
01= -01 dBm
1:256 2:64
Effective Default
Range
001~600 030
01~99 85
1, 2 1
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in.
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in.
1, 2 1 The resolution reverts to the default when
transmission is complete.
1~4 1 Set RX equalizer to automatical mode.
1~4 1
1,2 2
"START" input
"START" input
See TEST FUNCTIONS(P.74).
1, 2 2 See TEST FUNCTIONS(P.74).
1~3 1 Sets whether to monitor the line signal with the
unit´s speaker during FAX communication or not.
See TEST FUNCTIONS(P.74).
0 See TEST FUNCTIONS(P.74).
See TEST FUNCTIONS(P.74).
See TEST FUNCTIONS(P.74).
See TEST FUNCTIONS(P.74).
1, 2 1 Sets the % break of pulse sialing according PBX.
01~99 10 Sets the number of rings before the unit starts to
receive a document in the TEL mode.
00~99 03 Selects the number of redial times during FAX
communication (not including the first dial).
001~999 065 Sets the FAX redial interval during FAX
communication.
1~3 2 Lets you select the CNG output during FAX
transmission. ALL: CNG is output at phase A.
AUTO: CNG is output only when automatic dialing
is performed. OFF: CNG is not output at phase A.
Refer to SOMETIME THERE IS A TRANSMIT
PROBLEM(P.118).
1~3 1 See Symptom/Countermeasure Table for long
distance and international calls in. Refer to
RECEIVE PROBLEM(P.119).
1, 2 1 See Symptom/Countermeasure Table for long
distance and international calls in. Refer to
SOMETIME THERE IS A TRANSMIT
PROBLEM(P.118).
1~4 2 If the number of errors during transmission
exceeds this value, the sending side terminates
the call.
- 15~00 10 Selects the FAX transmission level. Refer to
SOMETIME THERE IS A TRANSMIT PROBLEM
(P.118)and RECEIVE PROBLEM (P.119).
20~48 43 Used when there is an error problem.
1, 2 1
See CALL SERVICE TROUBLESHOOTING
GUIDE (P.92)
72
Remarks
----------
----------
----------
----------
----------
----------