Wood Finish; Operating Instructions - Jacuzzi FUZION BATH SERIES 7260 Installation & Operation Instructions

Finishes
Wood frames are factory finished with a clear satin spar varnish. Periodic maintenance for the spar varnish is required.
Clean wood frame with mild household detergent. NOTE: Do not use harsh chemicals or cleaners.
CAUTION: Use of chemicals and/or chemical cleaners may be hazardous to your health.
Repairs to damaged finish should be made by a qualified wood refinisher, contact a professional furniture refinisher.
OPERATION
NOTE: These instructions pertain to all bath products manufactured by Jacuzzi Whirlpool Bath. Not all features dis-
cussed in this instruction pamphlet apply to all baths.
All baths manufactured by Jacuzzi Whirlpool Bath are designed for "fill and drain," which means the bath should be drained
after each use and filled with fresh water by the next bather. This is a health precaution, as these baths are not designed to hold
water continuously like pools or spas. If you want a unit designed to continuously hold water, see your Jacuzzi Whirlpool Bath
dealer for the complete line of whirlpool spas available.
Once the bath is installed, remove any residue or foreign materials left over from construction. Paint, tar, or other difficult surface
stains can be removed with paint thinner, turpentine, or isopropyl alcohol (rubbing alcohol). NOTE: Use these chemicals only on
SURFACE stains. Other dirt can be cleaned off with a mild liquid detergent on a damp cloth. Scrape off plaster with a wooden or
plastic edge; do not use metal scrapers, wire brushes or other metal tools, as they will damage the bath's surface.
Water Level
Close the drain and fill the bath until water is at least 1" to
2" (2,5 - 5,08 cm) above the highest jet (see water line indi-
cated in the illustration). Do not turn on the whirlpool sys-
tem at any time if the jets are not completely immersed in
water. Do not immerse the control panel by overfilling
the bath. Running the whirlpool system when there is insuf-
ficient water in the bath could result in water spraying outside
the bath area. Running the whirlpool system without water
will damage the recirculating pump.
IMPORTANT: When exiting the bath, the water level will drop
below the jets which could result in water being sprayed out
of the unit. To prevent this, you must turn unit off before
exiting bath.
Jacuzzi Whirlpool Bath DE99000A

WOOD FINISH

OPERATING INSTRUCTIONS

FILL TO AT LEAST
1" - 2" ABOVE HIGHEST JET
3/06
Controlling Whirlpool Action
The whirlpool action in your bath is influenced by three
factors – direction of flow, force of water, and force of air. All
baths manufactured by Jacuzzi Whirlpool Bath are equipped
with fully adjustable PowerPro
all three factors. Some baths have additional directionally
adjustable jets which can be adjusted for direction and flow of
air only.
Direction: To change the direction of the water flow, swivel
the jet nozzle to the desired angle. The jets can be directed
individually toward any location on your body to provide a
hydromassage. The jets can also be adjusted so that they all
point in the same direction (clockwise or counterclockwise)
to circulate the water in a circular motion around the bath,
causing a total whirlpool effect.
Water Force: The high volume, fully adjustable jets can
be adjusted to control the force of the water coming into the
bath. For robust action, increase the force of the flow by ro-
tating the jet handles to the left (counterclockwise). For a
more gentle effect, rotate the handles to the right (clockwise).
Customize water force by lowering water volume of one (1)
jet(s) to increase water force in another jet(s). Never run the
whirlpool system with all the jets closed.
Force of Air: The intensity of the hydromassage whirl-
pool action is determined by the amount of air inducted into
the water. As the amount of air is increased, the hydromas-
sage action increases. For maximum air induction, increase
the amount of air using the Air Flow Increase buttons on the
control panel. For fewer air bubbles, decrease the amount of
air using the Air Flow Decrease buttons on the control panel.
When the knobs are turned to the smallest circles, only water
is being circulated.
18
® jets, which are adjustable for