Related Manuals for Stanley CR27
Summary of Contents for Stanley CR27
- Page 1 CR27 HYDRAULIC CIRCULAR SAW USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 30673 8/2014 Ver. 7...
-
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► CR27 User Manual... -
Page 5: Safety Precautions
• Always keep critical tool markings, such as labels The CR27 Hydraulic Circular Saw will provide safe and and warning stickers legible. dependable service if operated in accordance with the •... - Page 6 • Cut at the rated operating speeds (gpm). • Only use saw blades manufactured by Stanley Hy- • Operate the saw at “no load” for 30 seconds in a draulic Tools. Stanley assumes no responsibility for...
-
Page 7: Electrical Hazards
50 kV phase-to-phase require a minimum clear- Branches hanging on an energized electrical conductor ance of 10 feet plus 4/10 of an inch (3 meters plus 10 shall be removed using non-conductive equipment. mm) for each kilovolt over 50 kV. CR27 User Manual ◄ 7... - Page 8 1.1–15.0 10-00 3.05 15.1–36.0 10-00 3.05 36.1–50.0 10-00 3.05 50.1–72.5 10-09 3.28 72.6–121.0 12-04 3.76 138.0–145.0 13-02 4.00 161.0–169.0 14-00 4.24 230.0–242.0 16-05 4.97 345.0–362.0 20-05 6.17 500.0–550.0 26-08 8.05 785.0–800.0 35-00 10.55 Exceeds phase-to-ground. 8 ► CR27 User Manual...
- Page 9 Aerial devices and attached equipment (such as chip- pers) contacting energized electrical conductors shall be considered energized. Contact shall be avoided, except where emergency rescue procedures are being carried out. Emergency rescue should be performed in accor- dance with 4.3. CR27 User Manual ◄ 9...
-
Page 10: Tool Stickers & Tags
TOOL STICKERS & TAGS DANGER DANGER THIS SAW BLADE OF THE CR27 WILL CONTINUE TO ROTATE Failure to use hydraulic hose labeled and certified FOR UP TO 15 SECONDS OR MORE AFTER RELEASING THE as non-conductive when using hydraulic tools on or near electric lines may result in death or ON/OFF TRIGGER. -
Page 11: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 12: Hose Recommendations
HOSE RECOMMENDATIONS 12 ► CR27 User Manual... -
Page 13: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements CR27 User Manual ◄ 13... -
Page 14: Operation
OC each of the nuts, tighten the locking nut one half only operation. For more details, please refer to the following instructions. wrench flat further. 14 ► CR27 User Manual... -
Page 15: Figure 2. Correct Rotation Direction
Failure to heed • Carry the saw with the unit de-energized and the this precaution can result in severe personal injury. blade away from the body. CR27 User Manual ◄ 15... -
Page 16: Figure 4. Flush Cutting A Limb That Might Split Or Tear
For advice on specific wood cutting problems or the remaining limb down the center as the flush cut techniques for your area, consult your local Stanley is made. representative or your county agent. They can often provide information that will make your work safer and more productive. -
Page 17: Figure 6. Blade Sharpening
Special setting tool (Stanley part number 34653) is required to verify or prop- Using a file holder with a 7/16 inch round file (Stanley erly set the angle of each cutter tooth at .040 inch/1 mm. -
Page 18: Figure 8. Setting Cutter Tooth Angle
If the saw is to be used during cold weather, preheat the hydraulic fluid at low engine speed. When using the normally recommended fluids, fluid temperature should be at or above 50 °F/10 °C (400 ssu/82 centistokes) be- fore use. 18 ► CR27 User Manual... -
Page 19: Tool Protection & Care
This can cause damage to internal seals. • Always replace hoses, couplings and other parts with replacement parts recommended by Stanley Hydraulic Tools. Supply hoses must have a mini- mum working pressure rating of 2500 psi/172 bar. CR27 User Manual ◄ 19... -
Page 20: Troubleshooting
Have inspected and repaired by an authorized Stanley Hydraulic Tools dealer. Hydraulic oil leaks between valve Oil tube seals worn or oil tubes Have inspected and repaired by an handle and outer tube handle. worn. authorized Stanley Hydraulic Tools dealer. 20 ► CR27 User Manual... -
Page 21: Specifications
File Holder with 7/32 Round File (for sharpening brushcutter blades) .............. 11299 Setting Tool (for setting cutter angles on brushcutter) ..................34653 Certified Non-Conductive Dual Oil Resistant Hose, 3/8 in. Diameter × 10 ft with Guards......... 05005 CR27 User Manual ◄ 21... -
Page 22: Cr27 Parts Illustration
CR27 PARTS ILLUSTRATION Torque to 44 in-lb Lubricated 22 ► CR27 User Manual... -
Page 23: Cr27 Parts List
VALVE SPOOL (CR27891 ONLY) 67128 VALVE SPOOL (MODEL CR27191P ONLY) 07626 O-RING, 1/2 × 5/8 × 1/16* 31630 VALVE HANDLE 01605 O-RING (INCL W/ ITEM 37) 00936 ADAPTER 07627 O-RING, 5/8 × 3/4 × 1/16* CR27 User Manual ◄ 23... - Page 24 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...