Related Manuals for Stanley CO23
Summary of Contents for Stanley CO23
- Page 1 CO23 HYDRAULIC CUTOFF SAW USER MANUAL Safety, Operation and Maintenance © 2014 Stanley Black & Decker, Inc. New Britain, CT 06053 U.S.A. 72409 7/2014 Ver. 7...
-
Page 2: Declaration Of Conformity
Provisiones especiales: Disposizioni speciali: Representative in the Union: Patrick Vervier, Stanley Dubuis 17-19, rue Jules Berthonneau-BP 3406 41034 Blois Cedex, France. Vertreter in der Union/Représentant dans l’union/Representante en la Union/Rappresentante presso l’Unione Done at/Ort/Fait à/Dado en/Fatto a Stanley Hydraulic Tools, Milwaukie, Oregon USA... -
Page 3: Table Of Contents
REPAIRS AND / OR SERVICE TO THIS TOOL MUST ONLY BE DONE BY AN AUTHORIZED AND CERTIFIED DEALER. For the nearest authorized and certified dealer, call Stanley Hydraulic Tools at the number listed on the back of this manual and ask for a Customer Service Representative. -
Page 4: Safety Symbols
Always observe safety symbols. They are included for your safety and for the protection of the tool. LOCAL SAFETY REGULATIONS Enter any local safety regulations here. Keep these instructions in an area accessible to the operator and mainte- nance personnel. 4 ► CO23 User Manual... -
Page 5: Safety Precautions
• Do not operate the tool unless thoroughly trained. person. CO23 User Manual ◄ 5... -
Page 6: Tool Stickers & Tags
OPERATION MANUAL. OPERATION MANUAL. TAG TO BE REMOVED ONLY BY TAG TO BE REMOVED ONLY BY TOOL OPERATOR. TOOL OPERATOR. SEE OTHER SIDE SEE OTHER SIDE SAFETY TAG P/N 15875 (Shown smaller then actual size) 6 ► CO23 User Manual... -
Page 7: Hose Types
HOSE SAFETY TAGS To help ensure your safety, the following DANGER tags are attached to all hose purchased from Stanley Hydraulic Tools. DO NOT REMOVE THESE TAGS. -
Page 8: Hose Recommendations
HOSE RECOMMENDATIONS 8 ► CO23 User Manual... -
Page 9: Htma Requirements
2000 psi 2000 psi 2000 psi (at the power supply outlet) (172 bar) (138 bar) (138 bar) (138 bar) (138 bar) NOTE: These are general hydraulic system requirements. See tool specification page for tool specific requirements CO23 User Manual ◄ 9... -
Page 10: Operation
• Always replace hoses, couplings and other parts temperatures. Hydraulic fluids of petroleum base with replacement parts recommended by Stanley with anti wear properties and viscosity indexes over Hydraulic Tools. Supply hoses must have a mini- 140 will meet the recommended requirements over mum working pressure rating of 2000 psi/140 bar. -
Page 11: Operating Instructions
The speed of the motor output shaft should be checked at least every 100 hours of operation by trained and experienced personnel. A record of the speed checks should be maintained. The maximum rated speed of the CO23 User Manual ◄ 11... - Page 12 Wheels should not be stored where they will be exposed to high humidity, water, other liquids, or freez- ing temperatures. Temperatures low enough to cause condensation on the wheels when moving them from storage to an area of higher temperatures should be avoided. 12 ► CO23 User Manual...
-
Page 13: Troubleshooting
140 °F/60 °C. Power unit may be producing more flow than the saw will accept under the existing cutting conditions. Reduce flow until saw performance starts to drop off. CO23 User Manual ◄ 13... -
Page 14: Specifications
10-inch diameter Diamond Wheel for Masonry 1-inch Arbor ................03694 10-inch diameter Abrasive Wheel for Metal 1-inch Arbor Fast Cutting .............. 04116 10-inch diameter Abrasive Wheel for Metal 1-inch Arbor-Long Wear ..............04117 SERVICE TOOLS Description Part Number Bearing Installation Tool ............................05044 14 ► CO23 User Manual... -
Page 15: Co23 Parts Illustration
CO23 PARTS ILLUSTRATION CO23 User Manual ◄ 15... -
Page 16: Co23 Parts List
SEAL CARRIER 01211 O-RING 03823 SEAL * 01262 O-RING 01262 O-RING, 1 3/4 × 1 7/8 × 1/16 * 01362 O-RING 03822 SEAL CARRIER WASHER 01604 O-RING 03109 BEARING 03823 SEAL 03824 SEAL 01605 O-RING 16 ► CO23 User Manual... -
Page 17: Underwater Tools Depth Guideline
ROV operation is still limited to the tool, for Depth (ft) 8 GPM 12 GPM example a percussive tool has the same depth 5/8” 5/8” limitation whether ROV or diver operated. 3/4” 1” 1” 1” 1000 1” 1-1/4” CO23 User Manual ◄ 17... - Page 18 Stanley Hydraulic Tools 3810 SE Naef Road Milwaukie, Oregon 97267-5698 USA (503) 659-5660 / Fax (503) 652-1780 www.stanleyhydraulics.com...