Table of Contents
Advertisement
Repainting Your Grill
• After extended use and exposure to weather, paint on grill may
deteriorate or become spotted. Although this detracts from
grill's appearance, it will not impair its performance.
• To refinish your grill brush outside of grill lid and bottom with
wire brush and lightly sand with fine grit sandpaper. Sanding
allows new paint to adhere more easily. Wash grill lid and
bottom with soap and water to remove dust and grease. Do not
use a grill cleaner on outside of grill. Wipe with vinegar.
Refinish outside with heat-resistant paint. Do not paint inside
of grill.
CAUTION
NATURAL HAZARD • SPIDERS
FACT: Sometimes spiders and other small insects climb into
the burner tubes attached to the burners. The spiders spin
webs, build nests and lay eggs. The webs or nests can be
very small, but they are very strong and can block the flow of
gas. Clean burners prior to use after storing, at the beginning
of grilling season or after a period of one month not being
used.
Typical spider webs inside burner.
Spider guards are on the air intakes in an effort to reduce this
problem, but it will not eliminate it! An obstruction can result
in a "flashback" (a fire in the burner tubes). The grill may still
light, but the obstruction does not allow full gas flow to the
burners.
IF YOU EXPERIENCE THE FOLLOWING:
1.
Smell gas.
2.
Burner(s) will not light.
3.
A small yellow flame from burner (should be blue).
4.
Fire coming from around or behind control knob.
STOP!
Immediately turn off gas at LP tank!
SOLUTION:
Wait for grill to cool.
Follow the "
Cleaning The Burner Assembly
Clean burners often. Use a 12" pipe cleaner to clean out the
burner tubes. You may also force a stream of water from a
hose nozzle through burner tubes to clean them.
22 • 463843104
Cleaning The Burners
Follow these instructions to clean and/or replace parts of burner
assembly or if you have trouble igniting grill.
1.
2. Remove cooking grate.
3. Remove can from grease clip.
4. Remove screws holding burners to grill bottom.
5. Rotate burners approx. 45 degrees while lifting out of grill
6.
7. To remove air shield for cleaning, disconnect ignitor wire from
8. If grill is to be stored, coat burners lightly with cooking oil.
VERY IMPORTANT: Burner tubes must engage valves. See
9. Before cooking again on grill, follow
Storing Your Grill
• Clean cooking grates.
• Store in dry location.
• When LP tank is connected to grill, store outdoors in well-
• Cover grill if stored outdoors.
• Store grill indoors ONLY if LP tank is turned off and
" instructions.
• When removing grill from storage follow
Turn gas off at control knobs and LP tank.
bottom to disengage burner tube from valves.
Clean outside of burner with soap and water. Lay burner
upside down on flat surface. Force a stream of water through
tubes. Make sure water comes out of all burner holes. Open
clogged holes with a thin wire.
examine holes. Due to normal wear and corrosion, some
holes may become enlarged. If any large cracks or holes are
found replace burner.
electrode wire beneath grill bottom. Wash air shield with
concentrated grill cleaner or use soap and water solution and
dry thoroughly. Return air shield to grill bottom and connect
ignitor wire to electrode wire.
Wrap in protective cover to keep insects out. If not storing grill,
tilt burners approx. 45 degrees and insert burner tubes into
holes in front of grill bottom to engage valves. Rotate burners
to flat position and attach to grill bottom with screws.
illustration below for proper burner-to-valve engagement.
ventilated space and out of reach of children.
disconnected, removed from grill and stored outdoors.
Assembly"
instructions before starting grill.
Shake out excess water
and
"Burner Flame Check"
Burner
Valve
"Cleaning Burner
.
Advertisement
Table of Contents
