Important Note; Changes From Previous Edition - Gemini GEM-P9600 Programming Instructions Manual

THIS MANUAL INCLUDES FEATURES WHICH ARE ONLY AVAILABLE IN CONTROL PANEL FIRMWARE
VERSION 20 OR LATER.
This manual supports the keypad programming of the GEM-P9600 control panel with the NAPCO "classic" GEM-
RP2ASe2, GEM-RP3DGTL and GEM-RP4RFC/GEM-RP4C keypads as well as the GEM-K2AS, GEM-K3DGTL and
GEM-K4RF/GEM-K4 "K Series" keypads. The new "K Series" models offer the new STAY and AWAY buttons with sim-
plified functionality, along with the new MENU and ENTER buttons. While the instructions in this manual are depicted
using the "K Series" keypads, the manual applies to both the "classic" and the "K Series" keypads.
Program Mode is the same for both keypads--only the button names have changed, as follows:
A
• The
button and the
D
• The
button and the
• The
button and the
"NEXT/YES button" are used in this manual.
• The
button and the
"PRIOR/NO button" are used in this manual.

CHANGES FROM PREVIOUS EDITION

This manual (WI1185) contains revised Installation Instructions previ-
ously found in WI777D. The revisions are as follows:
Pages 6-21: Easy Program Menu includes new selections: 24 Hour Zones in
Area 1, Chime Zones in Area 1, Chime 2 Zones in Area 1, Exit/Entry2
Zones in Area 1, 50 mS Loop Response Zones, Aux Output Activated on
Alarm Zones, Sensor Watch Zones, Keypad Sounder On Alarm Zones,
Auto Bypass Re-entry Zones, Enable No EOLR Zones, Enable Telco Line
Fault Test, Enable Burg Output Chirp on KeyFob, Enable SIA CP-01 Fea-
tures.
Page 39, address 2421, "Telco Answering Service Override" name changed to
"2nd Call Answering Machine Override".
Page 46, added address 2417, bit 5, "Lug E4 Armed Away Only".
Panel includes added features to accommodate the SIA CP-01 False Alarm Re-
duction Standard. Therefore Direct Address Program Mode addresses
have been modified or added, as follows:
Page 47, modified address 2422, bit 6, Enable Bell Output on Keyfob Arming
Page 47, added address 2421, bit 3, Aux. Output Chirp on Keyfob Arm/Disarm
Page 47, added address 2421, bit 4, Don't Clear Aux. Relay with Disarm
Page 48, added address 3905, bit 1, Exit Time Restart
Page 48, added address 3905, bit 2, Sound Alarm on Exit Error
Page 48, added address 3905, bit 3, Rpt Exit Err/Recent Close
Page 48, added address 3905, bit 4, Digital Dialer Rpt Enter/Exit Test Mode
Page 48, added address 3905, bit 5, Enable CP-01 Limits
Page 48, added address 3905, bit 6, Disable Call Waiting on First Attempt
Page 48, added address 3905, bit 7, Enable Ambush in User Assignment
Code Type
Page 28, modified address 4082, Report Cancel Window.
Address Number Index added at end of manual.
Page 4, the following statement added: "Note: Unattended downloading from a
computer is not allowed for Fire Alarm or UL installations."
Pages 4, 5, and 7, "50mS Loop Response Zones", since the time of 50 mS does

IMPORTANT NOTE

R
button operate identically (in Program Mode) for both keypads.
U
button operate identically (in Program Mode) for both keypads.
button operate identically (in Program Mode) for both keypads. The words
button operate identically (in Program Mode) for both keypads. The words
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call toll free: (800) 645-9445
not meet the UL listing requirement of the panel, the following notation is
made: "750 mS is required for Loop Response time in UL installations".
Page 7, "Auto Bypass Re-entry Zones" notation added: "Not evaluated by UL".
Page 10, "Enter User Codes", instructions modified to enter a code from "3 to 6"
digits.
Area Options/Explanation chart at the top of page 11: the following information
added: "Ambush: Allows user code to send Ambush signal to Central
Station".
In Zone Options (pages 40-45) and the wiring diagram (page 72), the following
notation added: "Disable Auto-Reset on non-fire zones for SIA CP-01 in-
stallations".
Added to Zone Options (pages 40-45) and on page 47, address 2422, bit 0: "In UL
installations, all Fire Zones must also be programmed for 'Pulsed Burg
Output' and 'Fire Output Cadence' (Address 2422, bit zero)".
Page 59, Table 4: the following notation added: "Keypad Tamper must be en-
abled in UL installations".
Pages 40-44, added to Zone Options, "Interior (STAY) Bypass", addresses 1284,
1384, 1484, 1584, 1684, 1784, 1884, 1984, 2084, 2184, 2284, 2384.
Page 46, notation added to address 2419, bit 0: "
Series " keypads".
Page 47, address 2422, bit 5, "Disable Exit/Entry Urgency Tone at Keypad"
changed to "Disable Entry Urgency Tone at Keypad".
NAPCO Security Systems, Inc.
For direct line to Technical Service,
call toll free: (800) 645-9440
Internet: http://www.napcosecurity.com
*Do not use on systems with "K