Realignment - Kenwood TK-2202L Service Manual

1. Modes
User mode
PC mode Data programming
mode
Clone mode
Mode
User mode For normal use.
PC mode Used for communication between the
transceiver and PC (IBM compatible).
Data programming Used to read and write frequency data
mode and other features to and from the
transceiver.
PC test mode Used to check the transceiver using
the PC. This feature is included in the
FPU.
Clone mode Used to transfer programming data
from one transceiver to another.
2. How to Enter Each Mode
Mode
User mode Power ON
PC mode Received commands from PC
Clone mode [PTT]+[Side2]+Power ON (Two seconds)
3. PC Mode
3-1. Preface
The transceiver is programmed using a personal computer,
a programming interface (KPG-22/22A), USB adapter (KCT-53U)
and programming software (KPG-87D).
The programming software can be used with an IBM PC
or compatible. Figure 1 shows the setup of an IBM PC for
programming.
3-2. Connection procedure
1. Connect the transceiver to the personal computer with the
interface cable and USB adapter (When the interface cable
is KPG-22A, the KCT-53U can be used.).
Notes:
• You must install the KCT-53U driver in the computer to use
the USB adapter (KCT-53U).
• When using the USB adapter (KCT-53U) for the first time,
plug the KCT-53U into a USB port on the computer with the
computer power ON.
2. When the POWER is switched on, user mode can be
entered immediately. When the PC sends a command,
the transceiver enters PC mode.
When data is transmitting from the transceiver, the red
LED lights.
When data is received by the transceiver, the green LED lights.

REALIGNMENT

PC test mode PC tuning mode
Function
Operation
Notes:
• The data stored in the computer must match the model
type when it is written into the EEPROM.
• Change the transceiver to PC mode, then attach the
interface cable.
3-3. KPG-22/KPG-22A description
(PC programming interface cable: Option)
The KPG-22/22A is required to interface the transceiver with
the computer. It has a circuit in its D-sub connector (KPG-22 :
25-pin, KPG-22A : 9-pin) case that converts the RS-232C logic
level to the TTL level.
The KPG-22/22A connects the SP/MIC connector of the
transceiver to the RS-232C serial port of the computer.
3-4. KCT-53U description (USB adapter : Option)
The KCT-53U is a cable which connects the KPG-22A to a
USB port on a computer.
When using the KCT-53U, install the supplied CD-ROM
(with driver software) in the computer. The KCT-53U driver
runs under Windows 2000 or XP.
3-5. Programming software KPG-87D description
KPG-87D is the programming software for the transceiver
supplied on a CD-ROM. This software runs under Windows
98, ME, Windows 2000 or XP on an IBM-PC or compatible
machine.
The data can be input to or read from the transceiver and
edited on the screen. The programmed or edited data can be
printed out. It is also possible to tune the transceiver.
IBM-PC
KPG-87D
RF Power meter
or SSG
PC PC
D-SUB D-SUB
(25-pin) (9-pin)
KPG-22
Transceiver Transceiver
Fig. 1
TK-2202L
KPG-22 or KPG-22A or KPG-22A + KCT-53U
Illustration is KPG-22.
Gray +
Gray/Black –
1.5D-XV Lead wire +
1.5D-XV Shield wire –
Tuning cable
(E30-3216-05)
PC
USB
KCT-53U
KPG-22A
KPG-22A
Transceiver
}
SP
}
MIC
3