Table of Contents
Advertisement
J O N S E R E D
Instruction Manual
Manuel d'instructions
Bedienungsanweisung
Manual de instrucciones
Please read these instructions carefully and make
sure you understand them before using this unit.
English
Avant d'utiliser cet appareil, veuillez lire attentive-
ment les instructions et assurez--vous de les avoir
Français
comprises.
Lesen Sie diese Hinweise zur Handhabung des
Geräts aufmerksam durch. Verwenden Sie es erst,
Deutsch
wenn Sie sicher sind, daß Sie alle Anweisungen
verstanden haben.
Lea atentamente las instrucciones y asegúrese de
entenderlas antes de utilizar este unidad.
Español
S E R V I C E
530088108
4/4/02
Advertisement
Table of Contents
Related Manuals for Jonsered GT26D
Summary of Contents for Jonsered GT26D
- Page 1 J O N S E R E D S E R V I C E Instruction Manual Please read these instructions carefully and make sure you understand them before using this unit. English Manuel d’instructions Avant d’utiliser cet appareil, veuillez lire attentive- ment les instructions et assurez--vous de les avoir Français comprises.
-
Page 2: Identification Of Symbols
IDENTIFICATION (WHAT IS WHAT?) ON/STOP Transport Tube Switch Guard Trottle trigger Blade Assist handle Shield adjustment Starter handle Handlebar Nose cone Cylinder cover Shoulder Strap Choke Instruction Fuel tank Hex key Manual Air filter cover IDENTIFICATION OF SYMBOLS WARNING! This brushcutter can be dangerous! Careless or improper use can cause serious or even fatal injury. -
Page 3: Safety Rules
SAFETY RULES WARNING: Hazard Zone When using gardening appliances, basic safety precautions must al- ways be followed to reduce the risk of fire and serious injury. DANGER: This power tool can be 15 Meters dangerous! This unit can cause serious injury including amputation or blindness to the op- erator and others. - Page 4 S Keep handles free of oil and fuel. CUTTING SAFETY S Always use the handlebar and a properly adjusted shoulder strap with a blade (see WARNING: Inspect the area to be ASSEMBLY). cut before each use. Remove objects (rocks, UNIT/MAINTENANCE SAFETY broken glass, nails, wire, string, etc.) which can be thrown or become entangled in the WARNING:...
- Page 5 ASSEMBLY CARTON CONTENTS Check carton contents against the following list: Drive shaft S Brushcutter S Tube mounting screws (2) S Tube mounting nuts (2) S Handlebar screws (2) S Blade guard screws (4) S Cupped washer (1) S Large nut for installing blade (1) S Long hex key wrench (1) S Short hex key wrench (1) S Bracket cover...
- Page 6 ATTACHING THE CONTROL HANDLE TO THE HANDLEBAR NOTE: Make sure the wire going to the con- HARNESS trol handle is routed below the tube and re- ADJUSTMENT mains on the right side of the handlebar and FOR BALANCE the tube. 1.
- Page 7 Do not use any blades, or fastening hardware other than the washers and nuts shown in the following illustrations. These parts must be provided by Jonsered, and installed as shown below. Failure to use proper 8. Tighten blade nut firmly with a wrench while parts can cause the blade to fly off and seriously holding screwdriver in position.
-
Page 8: Operation
OPERATION BEFORE STARTING ENGINE Lock Button Lock--out WARNING: Lever Be sure to read the fuel information in the safety rules before you be- gin. If you do not understand the safety rules, do not attempt to fuel your unit. Contact an au- Throttle Trigger thorized service dealer. -
Page 9: Starting A Warm Engine
OPERATING INSTRUCTIONS FOR fore releasing the throttle trigger from the starting position. Release the throttle lock USE WITH WEED BLADE by squeezing and releasing the throttle trig- S Blade Thrust is a reaction that only occurs NOTE: ger. If engine dies with the choke when using a bladed unit. -
Page 10: Maintenance
Bring the engine to cutting speed before enter- RECOMMENDED CUTTING POSITION ing the material to be cut. If the blade does not 2 o’clock turn when you squeeze the throttle trigger, make Cut using the 2 sure tube is fully inserted into the engine. o’clock to 4 o’clock Always release the throttle trigger and allow 4 o’clock... -
Page 11: Seasonal Storage
STORAGE ENGINE WARNING: Perform the following S Remove spark plug and pour 1 teaspoon of steps after each use: 40:1, 2-cycle engine oil (air cooled) through S Allow engine to cool before storing or trans- the spark plug opening. Slowly pull the porting. -
Page 12: Troubleshooting Table
EU Declaration of Conformity relating to 2000/14/EC We, Poulan/Weed Eater, Division Electrolux North America, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, declare under sole responsibility that the Jonsered model GT26D brushcutter was assessed in accordance with Annex V of the DIRECTIVE and from serial numbers 2001--305N00001 and onwards, conforms to the provisions of the DIRECTIVE. -
Page 13: Technical Data Sheet
We, Poulan/Weed Eater, Division Electrolux North America, Inc., Texarkana, TX, 75501, USA, Tél. : +1 903 223 4100, Declare under sole responsibility that brushcutter Jonsered GT26D from serial numbers 2001--305N00001 and onwards, follows the provisions of the DIRECTIVES : 98/37/EC (machinery) and 89/336/EEC (electromagnetic compatibility) , including amendments and is in conformity with the following standards: EN 292- -2, EN ISO 11806 and CISPR 12.