Vermont Castings WDVST500 Installation & Operating Instructions Manual page 36

WDV See-thru Gas Fireplace
Setting privacy code on Transmitter:
Figure 43
The remote transmitter privacy code is preset in factory.
In the event of activation or interference from other nearby
transmissions, change the code using the following pro-
cedures (learn function must be performed after changing
the code):
1. Press the ON/arrow button and
the TIMER button at the same
time to enter privacy code setup
mode.
2. The setup display is shown in the
figure. The four digits on the top
stand for the privacy code (as the
actual DIP switches on Ambient's
previous remotes). The default
values of the four digits will be all
"1" (ON).
3. The first digit will be flashing upon
entering the setup mode. Push the ON button to toggle
its value between "0" (OFF) and "1"(ON), and push the
"OFF" button to jump to the next digit. The next digit
will then start flashing and the first one stops flashing.
Set up the four digits to your choice.
4. After setting up all the four digits, push "OFF" to finish
the process and return to the previous mode.
5. The Signature Command control board then needs to
re-learn the new setting.
performing learn Function
1. The RF receiver button on the control board in the fire-
place must be in the on position before the learn func-
tion can begin. Figure 44. With the Command Center
master switch in the ON position, use paper clip to de-
press the recessed button on Control Board, one beep
for RF receiver ON or two beeps for RF receiver OFF.
2. Holding the OFF button on the Command Center
while turning on the
master switch will
activate the learn
function for the
transmitter.
3. After the above op-
eration, two beeps
will be given and
the green LED on
the Command Cen-
ter will flash for 10
seconds.
36
Figure 43
FP2649
set privace code
RF Receiver
ON/OFF
control Board
Figure 44
TOuch Screen reMOTe cOnTrOl OperaTIOn
LED
OFF
Figure 45 -
Command Center
Battery Door
4. During the 10 seconds, press the OFF button on the
transmitter to learn. Another two beeps will be given to
confirm a successful learning. Figure 45
FP2650
command ctr ctrl brd
Do not use two (2) or more remote control sys-
tems in the same area with the same privacy
code setting, as they will communicate with
each other. This may cause the appliances to
malfunction.
resetting the transmitter:
If the transmitter is not working properly, reinstall the bat-
teries to reset the transmitter.
1. Pull out at least one of the batteries.
2. Press any key on the screen to discharge.
3. Wait for 10 seconds and reinstall the batteries.
Pushing and holding any key for more than 10 seconds
until the display refreshes will also reset the transmitter.
n Functions and Operations
General:
The TSFSC Remote Control has four (4) operating modes:
Manual, Timer, Thermostatic and Smart Mode
stat. The control system can be set to temperature range
between 45° F and 90° F. The blower speed and flame
height can be adjusted in the manual, timer and thermo-
static mode. The Smart Mode
cally adjust flame height and blower speed according to
the difference between Set and Room temperatures.
The transmitter will operate the remote receiver from 1
foot to a maximum of 30 feet. The distance is reduced
when batteries are low.
Manual Mode
Figure 46
In this mode, the TIMER button and the THERMO but-
ton will only display "TIMER" and "THERMO", respec-
tively without showing the time and the SET temperature.
Pressing the ON/up and OFF/down buttons will change
the flame height if none of the menu buttons (TIMER,
THERMO, LIGHT, FAN, AUX) are pressed and flashing.
FP2650
command ctr ctrl brd
ON
Master Switch
FP2650
Front Panel Bezel
Optional
®
thermostat will automati-
®
thermo-
78D2082