COLOR MONITOR SERVICE MANUAL CHASSIS NO. : CL-29 FACTORY MODEL: LB782F MODEL: FPD1700 CAUTION BEFORE SERVICING THE UNIT, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Signal Connector Pin Assignment • DVI-I Connector (Digital/Analog) Signal (DVI-I) Signal (DVI-I) Hot Plug Detect T. M. D. S. Data2- T. M. D. S. Data2+ T. M. D. S. Data0- T. M. D. S. Data0+ T. M. D. S. Data2/4 Shield T.
PRECAUTION WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING BE CAREFUL ELECTRIC SHOCK ! • There are some special components used in LCD monitor that are important for safety. These parts are • If you want to replace with the new backlight (CCFL) or marked on the schematic diagram and the inverter circuit, must disconnect the AC adapter...
TIMING CHART VIDEO SYNC << Dot Clock (MHz), Horizontal Frequency (kHz), Vertical Frequency (Hz), Horizontal etc... (µs), Vertical etc... (ms) >> Sync Total Period Video Active Front Porch Sync Duration Back Porch Mode Resolution Frequency Clock Time (A) Sort Polarity 31.469 640x350 25.175...
OPERATING INSTRUCTIONS FRONT VIEW REAR VIEW AUDIO DC OUT Power Connector DVI port Power ON/OFF Button Power (DPMS) Indicator D-Sub Signal Port Front Control Panel AUTO/SET Button MENU Button Button Power Button SOURCE Button Power Indicator SOURCE MENU AUTO/SET 1. SOURCE Button 4.
DISASSEMBLY BACK COVER REMOVAL Caution: When you open the Back cover, Be careful! Dont stress the Control Board Connector. (b) Latch Point 1) Set the Monitor face downward. 3) Set the Monitor as picture. 2) Remove four screws (a). 4) Release the bottom & side latch. 5) Set the Monitor face upward.
DESCRIPTION OF BLOCK DIAGRAM (Main Board) 1. Input signal switching part. There are two inputs which are analog and digital input. They come from each 15 pin D-Sub and 29 pin DVI-I connector. 2. Video Controller Part. This part amplifies the level of video signal for the digital conversion and converts from the analog video signal to the digital video signal using a pixelclock.
BLOCK DIAGRAM POWER BOADR 50 ~ 60Hz 100KHz HVDC INPUT RECTIFIER ENERGY OUTPUT RECTIFIER COMPONENTS AND FILTER TRANSFER AND FILTER LINE 100 ~ 240V PWM CONTROL PHOTO-COUPLER SIGNAL CIRCUIT ISOLATION COLLECTION SECONDA RY PRIMARY DESCRIPTION OF BLOCK DIAGRAM 1. EMI components. This part contains of EMI components to comply with global marketing EMI standards like FCC, VCCI CISPR, the circuit included a line-filter, across line capacitor and of course the primary protection fuse.
ADJUSTMENT All adjustment are thoroughly checked and corrected 3. Adjustment for White Balance when the monitor leaves the factory, but sometimes 1) Display color 0,0 pattern at Mode 15. several minor adjustment may be required. 2) Set External Bright to MAX position and Contrast to Adjustment should be following procedure and after MAX Position.
TROUBLESHOOTING GUIDE 1. NO POWER NO POWER (POWER INDICATOR OFF) CHECK J801 TROUBLE IN INPUT VOLTAGE BULT-IN POWER (12V) ? CHECK J801 TROUBLE IN 5VST VOLTAGE BULT-IN POWER (5V) ? CHECK U501’s PIN 6. TROUBLE IN IS THIS PIN U501 or X501 OSCILLATED? TROUBLE SOMEWHERE ELSE...
Page 14
2. NO RASTER NO RASTER CHECK TROUBLE IN J702 PIN 1, 2, 3 BULT-IN POWER (12V) ? or L703, L704 CHECK TROUBLE IN J702 PIN 8 (5V) ? INVON PATTERN CHECK TROUBLE IN X501 X501 H. PULSE ? CHECK TROUBLE IN U201(GM5020) ? U201 CHECK...
Page 16
3. NO CLOCK (CLOCK GENERATOR) NO DOT CLOCK CHECK TROUBLE IN X201 24MHz ? X201 CHECK TROUBLE IN L201 U201 CLOCK ?
Page 17
4. TROUBLE IN DPM TROUBLE IN DPM CHECK PC CHECK PC IS NOT GOING R233, R234? INTO DPM OFF MODE CHECK U501 PIN 6 TROUBLE IN WAVEFORM X501 (24MHz) ? CHECK TROUBLE IN U501 PIN 11 SIGNAL CABLE (0V) ? TROUBLE IN PC...
REPLACEMENT PARTS LIST CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS, READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL. * NOTE SAFETY Mark AL ALTERNATIVE PARTS DATE: 2002. 2. 01. DATE: 2002. 2. 01. *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC.
PIN CONFIGURATION BA7657 Multimedia ICs BLOCK DIAGRAM Red 1 input HD 1 input HD Sync Signal detector HD 2 input Green 1 input HD output Ground Red output DET. Blue 1 input Ground Green output Composite video input Red 2 input (Sync on Green) Syncsepa Ground...
Page 30
BA033 Low Saturation Voltage type 3-terminal Regulator Reference Voltage 1. Vcc 2. GND 3. OUTPUT BLOCK DIAGRAM KA7812 ( KA7808 , KA7805) Positive Voltage Regulator 5V (8V, 12V) BLOCK DIAGRAM 1: Input 2: GND 3: Output TYPE PARTS TYPE PARTS Regulator Transistor KA78M05R...