Copyright of the whole product as integration, including its accessories and software, belongs to Shenzhen Tenda Technology Co., Ltd. Without the permission of Shenzhen Tenda Technology Co., Ltd, any individual or party is not allowed to copy, plagiarize, imitate or translate it into other languages.
CONTENTS Chapter 1 Introduction ......1 Product Features ......2 Package Contents ......4 LED Indicator and Port Description ..4 Chapter 2 Hardware Installation ....8 2.1 How to Install the Router ..... 8 2.2 Network Application Plan ....10 Chapter 3 How to Login to the Router ..
3G 11N Wireless Router Chapter 1 Introduction Thank you for purchasing Tenda 3G611R+ 11N Wireless Router! 3G611R+ is a high speed 3G 11N Wireless Router, which complies with latest IEEE802.11n IEEE802.11b/g standards and provides up to 150Mbps wireless receiving and transmitting rate with its wireless transmitting distance 3 times farther than G-products.
Then, the included “Setup Wizard” is developed by Tenda especially for less IT-savvy users to install the device within seconds. In a word, 3G611R+ is your premier choice to share the Internet via 3G, wireless broadband, and wired broadband access ways.
Page 8
3G 11N Wireless Router Ethernet WAN port Provides four 10/100Mbps Auto-Negotiation Ethernet LAN ports Provides one USB 2.0 port for 3G modem card connection Supports xDSL/Cable MODEM, static and dynamic IP in community networking Supports remote/local Web management ...
One CD-ROM If any of the listed items are missing or damaged, please contact the Tenda reseller from whom you purchased for replacement immediately. LED Indicator and Port Description Front Panel and LED Indicator Show LED indicator description on front panel: (from R to L) POWER ...
Page 10
3G 11N Wireless Router When turns green, Always ON indicates the power connects well. When blinking, it indicates the device is negotiating with client in WPS mode. When turns green, blinking indicates the system runs well. When turns green, Always ON indicates the USB port is connected well;...
Page 11
3G 11N Wireless Router Back Panel Show: Rear Panel:(From L to R) POWER The port is for power adapter connection. Please use the included DC 12V 1.5A power adapter. RESET The system reset button. Press this button for 7 seconds, the settings configured in this device will be deleted and it will restore the settings to the default one.
Page 12
3G 11N Wireless Router MODEM, Switch, Router and other Ethernet devices. It is always connected with DSL Modem, Cable Modem, or direct Internet line provided by ISP to access the Internet. LAN (1, 2, 3, 4) 4 10/100Mbps Ethernet ports can be connected with Ethernet switch, Ethernet router and NIC card.
3G 11N Wireless Router Chapter 2 Hardware Installation 2.1 How to Install the Router After you unpack the box, please follow the steps below to connect the device. For better wireless performance, please put the device in the middle of wireless coverage area.
Page 14
3G 11N Wireless Router 3. Connection between the Router and Network A. If you have a 3G USB modem card, please connect it to the Router's USB port to share 3G network. B. If you are provided the wired broadband by your ISP to access the Internet, please connect the Router's WAN port with the Internet access line.
3G 11N Wireless Router 4. Please insert the included CD-ROM into the CD-ROM drive. You can run the “Setup Wizard” automatically or click the “Setup” button manually and then follow the instructions to finish installation or enter the Router’s Web-based utility to set the device. (For more details please refer to chapter 3.) 2.2 Network Application Plan Usually Wireless LAN Network is deployed in a planned...
Page 16
3G 11N Wireless Router 1. Application Plan for 3G Network Connection 2. Application Plan for Wired Broadband Connection 3. Application Plan for Wireless Broadband Connection...
3G 11N Wireless Router Chapter 3 How to Login to the Router The chapter mainly presents how to enter the Router’s Web page. After you have finished the hardware installation (Please refer to chapter2.), the following steps will assist you to set the network configurations for you computer.
Page 18
3G 11N Wireless Router 2. Right click “Local Area Network Connection” and select “Properties”. 3 . Select “Internet Protocol (TCP/IP)” and click “Properties”.
Page 19
3G 11N Wireless Router 4.Select “Obtain an IP address automatically” or select “Use the following IP address (S)”. A. “Obtain an IP address automatically” as the following diagram: B. “Use the following IP address (S)” IP Address: 192.168.0.XXX: (XXX is a number from 2~254) Subnet Mask: 255.255.255.0 Gateway: 192.168.0.1...
3G 11N Wireless Router Tip: If you are not sure of the DNS server address, we recommend you to select “Obtain an IP address automatically (O)” and “Obtain a DNS server address automatically”. 3.2 Login to the Router 1.To access the Router’s Web-based interface, launch a web browser such as Internet Explorer and enter the Router’s default IP address, http://192.168.0.1.
Page 21
3G 11N Wireless Router 3. If you enter the correct user name and password, the screen will be the next one.
3G 11N Wireless Router Chapter 4 WAN Medium Type 4.1 WAN Medium Type The Router provides three access medium types. If you are provided the 3G broadband by your ISP to access the Internet, you can connect the 3G USB modem card to the Router’s USB port and select 3G WAN to set the device.
Page 23
3G 11N Wireless Router Internet, please select this type. Wired WAN: In this type the WAN link line must be wired. Please connect the access line to the WAN port on the Router’s rear panel. The default type is wired WAN.
3G 11N Wireless Router Chapter 5 Quick Setup Guide This chapter deals with how to access the Internet quickly. After you enter the Router’s Web-based interface from the Internet Explorer, please select the access medium type provided by your ISP in “WAN Medium”. After saving and rebooting the device, please select your connection type (PPPOE, Dynamic IP, and Static IP etc.) provided by your ISP to finish the basic settings.
Page 25
3G 11N Wireless Router During the installation, please select the type of 3G modem card and enter the basic parameters provided by your 3G ISP. Generally speaking, “Access Point Name” and “Dial” are the necessary settings, but some other modem cards need to set “PIN Code” or “User name/ Password”.
Page 26
3G 11N Wireless Router we’ll try our best to help you to solve the problem. 5.1.2 Wired Broadband Connection (via Wired WAN) If you are provided the wired broadband by your ISP to access the Internet, please select “Wired WAN” in the “WAN Medium”...
Page 27
3G 11N Wireless Router Dynamic IP, static IP, etc. In this chapter, we introduce you three common access way settings. If you are not sure of your access way, you can enable the auto-detect function to select your access way. ADSL Virtual Dial-up (via PPPoE) ...
Page 28
3G 11N Wireless Router Dynamic IP (via DHCP) If your connection mode is Dynamic IP, it means your IP address keeps changing every time you connect. You do not need to enter the information like other modes. Click “Next” and “Apply” to finish the settings. Static IP ...
Page 29
3G 11N Wireless Router Click “Apply” to complete the setup wizard. The Router will record the settings you made. To activate the settings, it is recommended to select “Reboot the Router” from “System Tool” of the left menu. It is rebooting now, please wait for a few minutes and DO NOT power off it.
Page 30
3G 11N Wireless Router 5.1.3 Wireless Broadband Connection (via Wireless WAN) If you are provided the wireless broadband by your ISP to access the Internet or you want to amplify wireless signals, please select “Wireless WAN” in “WAN Medium” page after you enter the Router’s setup page. Shown as the diagram below: Please enter the wireless SSID, MAC address, channel, security mode parameters provided by your Wi-Fi ISP.
Page 31
3G 11N Wireless Router settings. Select and save the settings, and you will enter the Router’s Web interface again after rebooting the Router. Then click “next” as the diagram show. The screen will show as the diagram below. The Router supports multiple access ways such as ADSL dial-up, Dynamic IP, and Static IP etc.
Page 32
3G 11N Wireless Router This way is used when the Router is connected to the wireless modem or you want to amplify wireless signals and share the Internet with multiple computers. Enter the Account and Password provided by your ISP, and click “Next”.
Page 33
3G 11N Wireless Router wireless signals are amplified and you can share the Internet with multiple computers. Notice: When you open the wireless WAN feature or when you have a wireless router before and you want to amplify wireless signals, please pay attention to the IP address the previous router distributed.
Page 34
3G 11N Wireless Router and Alternate DNS Server fields and click “Next”. For example: ISP provides the following TCP/IP parameters as follows: IP Address:192.168.1.2 Subnet Mask:255.255.255.0 Gateway:192.168.1.1 Primary DNS Server:210.21.196.6 Secondary DNS Server:211.5.88.88 You need to fill in the related parameters. Click “Save”...
Page 35
3G 11N Wireless Router After rebooting the Router, you can click the “Running Status” on the right menu to check the connection between the Router and ISP device. If the status information of the WAN port appears as the diagram show, it means you have finished the Router’s basic settings and you can surf on line now.
Page 36
3G 11N Wireless Router transmitting medium in wireless WAN connection type. When you use wireless WAN or 3G WAN, please make sure that the wireless network exists and the intensity and performance of wireless signals are OK. The methods to confirm the wireless feature are very simple.
3G 11N Wireless Router one computer to access the Internet, you can use the wired WAN function of the Router. Chapter 6 Advanced Settings 6.1 LAN Settings LAN Settings are for the basic TCP/IP parameters of LAN ports. MAC Address: The Router’s physical MAC address ...
3G 11N Wireless Router remember it for the Web-based Utility login next time. 6.2 WAN Settings After you have selected the ISP connection type in “Setup Wizard” and you want to modify the related settings, here you can modify and configure the settings in details.
Page 39
3G 11N Wireless Router The default value is 1492. Do NOT modify it unless necessary. But if some specific website or web application software can not be open or enabled, you can have a try to change the MTU value as 1450, 1400, etc.
Page 40
3G 11N Wireless Router Static IP If your connection mode, static IP is chosen, you can modify the following addressing information. IP Address: Here enter the WAN IP address provided by your ISP. Subnet Mask: Enter the WAN Subnet Mask ...
3G 11N Wireless Router 3G Broadband: Network settings 3G modem card type: choose the Model No. of your 3G USB modem card. Authentication method: access authentication methods include SIM card type and Username/Password type. PIN code: SIM card personal identification code. ...
3G 11N Wireless Router If your ISP doesn’t offer you the related parameters, you do not need to enter them. After configuring the settings correctly, click “Apply” button and wait for 60 seconds. Then you can access the Internet. Note: Please enter correct...
3G 11N Wireless Router Clone MAC Address: Register your PC's MAC address. Restore Default MAC Address: Restore to the default hardware MAC address. 6.4 DNS Settings DNS is short for Domain Name System (or Service), an Internet service that translate domain names into IP addresses which are provided by your Internet Service Provider.
3G 11N Wireless Router Chapter 7 Wireless Setting 7.1 Basic Settings Enable Wireless: Check to enable the Router’s wireless features; uncheck to disable it. Network Mode : Select one mode from the following. The default is 11b/g/n mode.
Page 45
3G 11N Wireless Router 11b mode: Allow the wireless client to connect with the device in 11b mode at the maximum speed of 11Mbps. 11g mode: Allow the 11g/11n-compliant client device to connect with the AP at the maximum speed of 54Mbps. 11b/g mode: Allow the 11b/g-compliant client device to connect with the AP with auto-negotiation speed, and 11n...
Page 46
3G 11N Wireless Router via wireless adapter, and configure PC1 and PC2 in the same segment. After the feature is enabled, two PCs can not communicate and share network resource each other, but they can communicate with wireless clients connected with AP2. This feature is to isolate the communication of wireless clients connected with the same SSID.
3G 11N Wireless Router Standard Channel:Specify the effective channel (from 1 to 13\Auto) of the wireless network. Extension Channel:To increase data throughput of wireless network, the extension channel range is used in 11n mode. Channel Bandwidth : Select channel ...
Page 48
3G 11N Wireless Router WPA Algorithms:Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard]. Pass Phrase: Enter the encrypted characters with 8-63 ASCII characters. Key Renewal Interval : Set the key’s renewal period. 7.2.2 WPA2- Personal WPA2 (Wi-Fi Protected Access version 2) provides higher security than WEP (Wireless Equivalent Privacy) (Wi-Fi...
Page 49
3G 11N Wireless Router WPA Algorithms:Provides TKIP [Temporal Key Integrity Protocol], AES [Advanced Encryption Standard] or TKIP&AES mixed mode. Pass Phrase:Enter the encrypted characters with 8-63 ASCII characters. Key Renewal Interval : Set the key’s renewal period. 7.2.3 Mixed WEP WEP (Wired Equivalent Privacy), a basic encryption method, usually encrypts wireless data using a series of...
Page 50
3G 11N Wireless Router Select SSID : Select the SSID (main SSID or minor SSID) to configure security setting from the drop-down menu. Security Mode:From the drop-down menu select the corresponding security encryption modes. WEP Key:Set the WEP key with the format of ...
Page 51
3G 11N Wireless Router 7.2.4 WPA- Enterprise This security mode is used when a RADIUS server is connected to the device. Select “WPA-Enterprise” from the drop-down menu to enter the following window: WPA Algorithms:Provides TKIP [Temporal Key Integrity Protocol] or AES [Advanced Encryption Standard].
Page 52
3G 11N Wireless Router Session Timeout : The authentication interval period between the Router and authentication server. 7.2.5 WPA2-Enterprise This security mode is based on Radius authentication server and WPA2 encryption method. WPA2 is used when a RADIUS server is connected to the device. Select “WPA2-Enterprise”...
Page 53
3G 11N Wireless Router period. Radius Server Address:Enter the IP address of the Radius server. Radius Server port : Enter the authentication port of the Radius server. The default is 1812. Shared Key : Enter shared authentication server with 8~63 ASCII characters. Session Timeout :...
Page 54
3G 11N Wireless Router WEP:Click “Enable/Disable” to enable or disable the WEP algorithm. Radius Server Address:Enter the IP address of the Radius server. Radius Server Port : Enter the authentication port of the Radius server. The default is 1812. Shared Key :...
3G 11N Wireless Router three standard encryption methods: Open-None (Disable), WPA-Personal-AES, PA2-Personal-AES. Other encryption methods nonstandard. There may be compatibility problems among diffe rent manufacturers. 7.3 Advanced Settings This section is to configure the advanced wireless setting of the Router, including the BG Protection M ode, Basic Data Rates, Fragmentati on Threshold, RTS...
3G 11N Wireless Router Beacon Interval: Set the beacon interval of wireless radio. Default value 100. recommended not to modify this value. Fragment Threshold: fragmentation threshold defines the maximum transmission packet size in bytes. The packet will be fragmented if the arrival is bigger than the threshold setting.
Page 57
3G 11N Wireless Router panel to configure it without selecting encryption method and secret keys by manual. In the “Wireless settings” menu, click “WPS settings” to enter the next creen. WPS settings:To enable or disable WPS function. The default is “disable”. WPS mode:Provide two way s: PBC (Push-Button ...
Page 58
3G 11N Wireless Router minutes later, the WPS indicator will be off, which means the WPS connection is completed. If more clients are added, repeat the above steps. At present, the WPS supports up to 32 clients access.) PIN:If this option is enabled, you need to enter a ...
3G 11N Wireless Router WPS client will be idle state, and WPS indicator will be turned off. AP will not respond the WPS client’s requests and the set the security mode as WPA mode. 7.5 WDS Settings WDS (Wireless Distribution System) is used to expand wireless coverage area.
3G 11N Wireless Router address into each own AP MAC address table by manual or scanner to enlarge and extend the wireless radio. Encrypt Type : Select one from WEP, TKIP, AES for security here. Pass ph rase: Enter the encrypted key for wireless devices.
3G 11N Wireless Router MAC Address Filter:Enable/disable MAC address filter. Select “off” to malfunction MAC address; “disable” to prevent the MAC addresses in the list from accessing the wireless network; “Allow” to allow the MAC address in the list to access the wireless network.
3G 11N Wireless Router Chapter 8: DHCP Server 8.1 DHCP Settings DHCP (Dynamic Host Control Protocol) is to assign an IP address to the computers on the LAN/private network. When you enable the DHCP Server, the DHCP Server will allocate automatically an unused IP address from the IP address pool to the requesting computer in premise of activating “Obtain an IP Address Automatically”.
3G 11N Wireless Router 8.2 DHCP List and Binding The Static IP assignment is to add a specifically static IP address to the assigned MAC address. You can view the related information in the DHCP server list. IP Address: Enter the IP address which needs to ...
3G 11N Wireless Router Chapter 9 Virtual Server 9.1 Single Port Forwarding The Router can be configured as a virtual server on behalf of local services behind the LAN port. The given remote requests will be re-directed to the local servers via the virtual server.
Page 65
3G 11N Wireless Router Internal Port: This is the port number of LAN computer set by the Router. The Internet traffic from the external port will forward to the internal port. For example:you can set the internal port NO.66 to act as the external port NO.21 for ftp service.
3G 11N Wireless Router NOTE: If you set the virtual server of the service port as 80, you must set the Web management port on Remote Web Management page to be any value except 80 such as 8080. Otherwise, there will be a conflict to disable the virtual server.
Page 67
3G 11N Wireless Router Start/End Port: Enter the start/end port number which ranges the External ports used to set the server or Internet applications. IP Address: Enter the IP address of the PC where you want to set the applications. Protocol: Select the protocol (TCP/UDP/Both) for ...
3G 11N Wireless Router 9.3 ALG Service Settings In the context of computer networking, an ALG or application layer gateway consists of a security component that augments a firewall or NAT employed in a computer network. It allows customized NAT traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data"...
3G 11N Wireless Router Usually allowing client applications to use dynamic ephemeral TCP/ UDP ports to communicate with the known ports used by the server applications, even though a firewall-configuration may allow only a limited number of known ports. In the absence of an ALG, either the ports would get blocked or the network administrator would need to explicitly open up a large number of ports in the firewall;...
3G 11N Wireless Router DMZ Host IP Address: The IP address of the computer you want to expose. Enable: Click the checkbox to enable the DMZ host. For example: Set the computer at the IP address of 192.168.0.10 in LAN as a DMZ Host to intercommunicate with another host on the Internet.
Page 71
3G 11N Wireless Router Enable UPnP: Click the checkbox to enable the UPnP.
3G 11N Wireless Router Chapter 10 Traffic Control 10.1 Traffic Control Traffic control is used to limit communication speed in the LAN and WAN. Up to 20 entries can be supported with the capability for at most 254 PCs' speed control, including for IP address range configuration.
3G 11N Wireless Router as HTTP service. IP Starting Address: The first IP address for traffic control. IP Ending Address: The last IP address for traffic control. Uploading/Downloading: To specify the traffic heading way for the selected IP addresses: uploading or downloading.
Page 74
3G 11N Wireless Router Enable traffic statistics: check to enable traffic statistics. Usually traffic statistics is disabled, which can improve the Router’s data handling. The default is disabled. If it is enabled, the page will update the PC’s traffic information automatically and be refreshed every 5 seconds.
3G 11N Wireless Router Chapter11 URL Monitor 11.1 URL Monitor This feature is used to record user’s Internet activity, so in terms of this feature, the administrator can check out and control what they can do and have done. Enable URL Monitor: ...
Page 76
500 entries. Receive E-mail Address: Input the received E-mail’s address here. For example: tenda@sina.com.cn SMTP Server Address: Input the SMTP server address here. If you are not clear what your SMTP server’s address is, you can find them from Help page of the registered e-mail.
Page 77
3G 11N Wireless Router Entry Triggering Interval: To set sending e-mail’s entry interval. The entry ranges from 100 to 500. For example: If you input 100 here, it means the Router will send an email from “Send Email Address” to “Receive Email Address”...
3G 11N Wireless Router Chapter 12 Security Settings 12.1 Client Filter Settings To benefit your further management to the computers in the LAN, you can control some ports access to Internet by data packet filter function. Client Filter: Check to enable client filter. ...
3G 11N Wireless Router Policy Name: Enter a name for the access policy selected. IP Start/End: Enter the starting/ending IP address. Port No.: Enter the port range based over the protocol for access policy. Protocol: Select one protocol (TCP/UDP/Both) ...
Page 80
3G 11N Wireless Router URL Filter: Check to enable URL filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy. Clear the Policy: Click “Clear” button to clear all settings for the policy.
3G 11N Wireless Router Days: Select the day(s) to run the access policy. Save: Select Save to enable the settings. For example: If you want the computer at the IP address of 192.168.0.123 to access the Internet from 9:00 to 18: 00 everyday and only can search the WEB pages contain the strings such as sina, sohu, and yahoo, you need to set the packet filtering list as the above diagram.
3G 11N Wireless Router MAC Address Filter: Check to enable MAC address filter. Access Policy: Select one number from the drop-down menu. Enable: Check to enable the access policy. Clear the Policy: Click “Clear” button to clear all ...
3G 11N Wireless Router Prevent Network Attack: Check to enable it for attack prevention. 12.5 Remote Web Management This section is to allow the network administrator to manage the Router remotely. If you want to access the Router from outside the local network, please select the “Enable”.
3G 11N Wireless Router Note: 1. If you want to login the device’s Web-based interface via port 8080, you need use the format of WAN IP address: port (for example http://219.134.32.101: 8080) to implement remote login. 2. If your WAN IP address starts and ends with 0.0.0.0, it means all hosts in WAN can implement remote Web management.
3G 11N Wireless Router Enable: Check to enable the local web management. MAC Address: Enter the MAC addresses of LAN computers. Note:1. In the default state, this feature is not enabled. All computers in the LAN can login the Web. 2.
3G 11N Wireless Router Chapter 13 Routing Setting 13.1 Routing Table The main duty for a router is to look for a best path for every data frame, and transfer this data frame to a destination. So, it’s essential for the router to choose the best path, i.e.
Page 87
3G 11N Wireless Router Subnet Mask: The network portion of the Destination LAN IP. Gateway: The gateway of the next hop, usually the Router or host’s IP address. Note: 1. The gateway must keep the same segment with the Router’s LAN IP address.
3G 11N Wireless Router Chapter 14 System Tools 14.1 Time Settings This section is to select the time zone for your location. If you turn off the Router, the settings for time disappear. However, the Router will automatically obtain the GMT time again once it has access to the Internet.
3G 11N Wireless Router 14.2 DDNS DDNS (Dynamic Domain Name System) supported in this Router. It is to assign a fixed host and domain name to a dynamic Internet IP address, which is used to monitor hosting website, FTP server and so on behind the Router.
Page 90
3322.org as follows: User name tenda Password 123456 Domain Name tenda.vicp.net After mapping the port in the virtual server, setting account information in DDNS server and in the address field entering http://tenda.3322.org, you can access the Web page.
3G 11N Wireless Router 14.3 Backup/Restore Settings The device provides backup/restore settings, so you need set a directory to keep these parameters. Backup Setting: Click “Backup” button to back up the Router’s settings and select the path for save. Click “Save”...
Page 92
3G 11N Wireless Router Restore Setting: Click “Browse” button to select the backup files. Click “Restore” button to restore previous settings.
3G 11N Wireless Router 14.4 Restore to Factory Default Setting This button is to reset all settings to the default values. It means the Router will lose all the settings you have set. So please Note down the related settings if necessary.
14.5 Upgrade Firmware The Router provides the firmware upgrade by clicking the “Upgrade” after browsing the firmware upgrade packet which you can download from www.tenda.cn. Browse: click this button to select the upgrade file. Upgrade: click this button to start the upgrading ...
3G 11N Wireless Router 14.7 Password Change This section is to set a new user name and password to better secure your router and network. User Name: Enter a new user name for the device. Old Password: Enter the old password. ...
3G 11N Wireless Router 14.8 System Log The section is to view the system log. Click the “Refresh” to update the log. Click “Clear” to clear all shown information. If the log is over 150 records, it will clear them automatically. Refresh: Click this button to update the log.
3G 11N Wireless Router Appendix Ⅰ:Glossary 3G, the 3rd Generation, refers to the third digital communication technology. It can manage multi-media such as image, audio, and video streams etc. and provide different communication services such as web browse, telephone session, and electronic business etc. CDMA2000 CDMA2000 ,also called CDMA Multi-Carrier, is one of the current three 3G standards in the world which was put...
Page 98
3G 11N Wireless Router Channel An instance of medium use for the purpose of passing protocol data units (PDUs) that used simultaneously, in the same volume of space, with other instances of medium use(on other channels) by other instances of the same physical layer (PHY),with an acceptably low frame error ratio(FER) due to mutual interference.
Page 99
3G 11N Wireless Router data. Therefore, all devices on a wireless network must use the same key and same type of encryption. There are 2 methods for entering the KEY; one is to enter a 16-bit HEX digit. Using this method, users must enter a 10-digit number (for 64-bit) or 26-digit number (for 128-bit) in the KEY field.
Page 100
3G 11N Wireless Router 802.1x Authentication Static WEP key is difficult to manage. When you change the key, you need to inform everyone. Once the key is disclosed, there is no security. In addition, since static WEP encryption has serious security holes, the WEP key can be decrypted by receiving multiple data.
In this part some questions and problems shown during the Router’s usage and installation will be given suggesting answers. If your problems are not in the list, please log into our website www.tenda.cn or send an E-mail to support@tenda.cn, and we will reply you in the earliest time.
Page 102
3G 11N Wireless Router 2. Forget the login password and can not enter the setting page. What can I do? Press the “RESET” button for 7 seconds to restore the Router to default settings. 3. The computer connected with the Router shows IP address conflict.
Page 103
3G 11N Wireless Router address to the bind21ing PC’s MAC address. Select “MAC Address Clone” in “Advanced Setting” to input your computer’s MAC address and click “Apply” to activate it. 6. How to share my computer’s source with other users in Internet? If you want Internet users to access the internal server via the Router such as e-mail server, Web, FTP, you can configure the “Virtual Server”...
3G 11N Wireless Router application and service port: Server Protocol Service Port WEB Server FTP Server Telnet NetMeeting 1503、1720 File Send:6891-6900(TCP) TCP/UDP Messenger Voice:1863、6901(TCP) Voice:1863、5190(UDP) PPTP VPN 1723 Iphone5.0 22555 SMTP POP3 7. Why can’t I use my 3G Modem Card to connect the Internet? Please make sure that you have inserted a SIM card into your 3G Modem Card, you have enabled...
Page 105
3G 11N Wireless Router is compatible with the Router. You can search the related model No. on the compatible product list. Please make sure that the 3G modem card model selected in the 3G Web interface matches the practical product and the settings you entered match the parameters by your ISP.
Page 106
3G 11N Wireless Router d. Please do not detach any antenna of the wireless Router when you are using the Router. After trying all the above steps, if you still can’t access the Internet, you can contact us for assistant. 9.Why do the charges increase after using a 3G Modem Card? a.