Page 1
INSTRUCTION MANUAL IMPORTANT INFORMATION: Please read these instructions carefully and make sure you understand them before using this unit. Retain these instructions for future reference. MANUAL DE INSTRUCCIONES INFORMACIÓN IMPORTANTE: Lea atentamente las instrucciones y asegúrese de entenderlas antes de utilizar esta aparato. Conserve las instrucciones para la referencia en el futuro.
IDENTIFICATION (WHAT IS WHAT?) Front Handle Front Hand Guard Starter Rope ON/STOP Switch Muffler Chain Bar Sprocket Hole Fuel Mix Fill Cap Bar Oil Starter Housing Fill Cap Bumper Spike Bar Guard Chain Brake Cylinder Cover Throttle Lock- -out Direction of Chain Rear Travel...
IDENTIFICATION OF SYMBOLS Starting Reminder Push the choke/fast idle Move ON/STOP switch to lever in to the HALF the ON position. CHOKE position. Pull choke/fast idle lever Pull the starter rope sharply out to the full extent (to with your right hand until the FULL CHOKE posi- the engine starts.
SAFETY NOTICE: Exposure to vibrations teners securely tightened. through prolonged use of gasoline powered S Use only McCulloch accessories and re- hand tools could cause blood vessel or nerve placement parts as recommended. damage in the fingers, hands, and joints of peo-...
Avoid Obstructions S Turn the engine off and let saw cool in a non-combustible area, not on dry leaves, straw, paper, etc. Slowly remove fuel cap and refuel unit. S Store the unit and fuel in an area where fuel vapors cannot reach sparks or open Clear The flames from water heaters, electric motors...
S Keep a good, firm grip on the saw with both S Low- -Kickback Chain, designed with a hands when the engine is running and don’t contoured depth gauge and guard link let go. A firm grip will help you reduce kick- which deflect kickback force and allow back and maintain control of the saw.
ATTACHING THE BAR & CHAIN 9. Install clutch cover. Be sure adjusting pin is in the adjusting pin hole in the guide bar. (If not already attached) CAUTION: It is very important when instal- WARNING ling the clutch cover that the adjusting pin : Recheck each assem- aligns into the adjusting pin hole in the bar.
5. Push lever on bar knob down to return le- Tighten Loosen ver to closed/locked position. chain chain WARNING : Failure to push lever on bar knob down to closed/locked position could result in serious personal injury or damage to your chain saw. 6.
CHAIN BRAKE ON/STOP SWITCH Ensure chain brake is disengaged by pulling the front hand guard back toward the front han- dle as far as possible. The chain brake must be disengaged before cutting with the saw. WARNING : The chain must not move when the engine runs at idle speed.
fully depressing the throttle trigger. Activate Disengaged the chain brake by turning your left wrist Engaged against the hand guard without releasing your grip around the front handle. The chain should stop immediately. Inertia activating function control WARNING : When performing the fol- lowing procedure, the engine must be turned Braking function control off.
Page 11
clear area before cutting by pulling out ex- Final cut here. 5 cm above posed and cleared logs first. center of notch. First cut TYPES OF CUTTING USED FOR 5 cm BUCKING WARNING : If saw becomes pinched Notch or hung in a log, don’t try to force it out. You 5 cm can lose control of the saw resulting in injury and/or damage to the saw.
IMPORTANT POINTS S Finish with your second cut. S Watch out for springpoles. Use extreme Using a log for support caution when cutting small size limbs. Slen- der material may catch the saw chain and be whipped toward you or pull you off balance. S Be alert for springback.
SERVICE AND ADJUSTMENTS A worn bar will damage your chain and make WARNING cutting difficult. : Disconnect the spark After each use, ensure ON/STOP switch is plug before performing maintenance, except in the STOP position, then clean all sawdust for carburetor adjustments. from the guide bar and sprocket hole.
CHAIN SHARPENING All Cutters Remove Damage Same Length WARNING : Improper chain sharpen- ing techniques and/or depth gauge mainte- nance will increase the chance of kickback Top Plate which can result in serious injury. Side Plate WARNING : Wear protective gloves S File chain to meet the specifications when handling chain.
S Chain moves at idle. See IDLE SPEED- -T S Before storing, drain all fuel from the unit. adjusting procedure. Start engine and allow to run until it stops. S Saw will not idle. See IDLE SPEED- -T ad- S Clean the unit before storing. Pay particu- justing procedure.
We, Husqvarna AB, SE- -561 82 Huskvarna, Sweden, Tel: +46- -36- -146000, as authorised representative in the Community, declare that the chain saw model McCulloch M4620 P---600 from serial numbers 2009- -031(N or D)00001 and onwards (the year is clearly stated on the rating plate, followed by the serial number), comply with the requirements of the COUNCIL’S...
TECHNICAL DATA SHEET Noise levels M4620 Engine M4620 Equivalent (see note 1) noise Cylinder volume, cm pressure level at operator’s ear, Stroke, mm measured according to relevant Idle speed, rpm 3000 international standards, dB(A) Recommended max. Equivalent (see note 1) noise...
STATEMENT OF WARRANTY Husqvarna Outdoor Products provides war- Nothing contained in this warranty is in- ranty to the initial purchaser for all products tended to purport to restrict, modify or ex- that are sold by an authorised Husqvarna clude the operation of any legislation in the Outdoor Products Dealer.