Service Manual Auto Washer Model: DWF-315W DWF-415S Caution : In this Manual, some parts can be changed for improving, their performance without notice in the parts list. So, if you need the latest parts information, please refer to PPL(Parts Price List) in Service Information Center (http://svc.dwe.co.kr).
AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER AUTO WASHER...
2. STRUCTURE OF THE WASHING MACHINE The parts and features of your washer are illustrated on this page. Become familiar with all parts and features before using your washer. NOTE • The drawings in this book may vary from your washer model. They are designed to show the different features of all models covered by this book, Your model may not include all features.
3. DIRECTIONS FOR INSTALLATION AND USE Installing Place Install the washer on a horizontal solid floor. If the washer is installed on an unsuitable floor, it could make considerable noise and vibration. Never install in these places The place where it would be exposed to direct sunlight.
How to Connect the Inlet Hose Be careful not to mistake in supplying between the hot (maximum : 50 C) and cold water. In using only one water tap or in case of attached one water inlet valve, connect the inlet hose to the cold water inlet valve.
How To Clean The Filter CLEANING THE LINT FILTER While pressing the handle of Remove the dirt inside the guide. CLEANING THE WATER INLET FILTER • Clean the filter when water leaks from, the water inlet. Pull the Turn off the Pull the Remove the dirt power plug...
4. FEATURE AND TECHNICAL EXPLANATION Feature of the Washing Machine ① First applying the Radical Technology in the world, go beyond washing, sterilize your colthes and deodorize a bad smell. ② The first air bubble washing system in the world. ③...
Automatic Draining time Adjustment This system adjusts the draining time automatically according to the draining condition. Good draining The washer begins spin process after drainage. Draining Bad draining Draininig time is prolonged. condition No draining Program is stopped and gives the alarm. FUNCTIONAL PRINCIPLE ①...
Automatic Unbalance Adjustment This system is to prevent abnormal vibration during intermittent spin and spin process. FUNCTIONAL PRINCIPLE Contact of safety switch Lid closing ① When the lid is closed, the safety switch contact is “ON” position. ② In case that wash loads get uneven during spin, the outer tub hits the safety switch Lid opening due to the serious vibration, and the spin...
Lint Filter Much lint may be obtained according to the kind of Filter clothes to be washed and some of the lint may also sticks to the clothes. Filter To minimize this possibility a lint filter is provided on the upper part of the tub to filter the wash water as it is discharged from the water channel.
Page 12
Gear Mechanism Ass'y The proper water currents is made by the rotation of pulsator at a low speed to prevent the damage to the small sized clothes. Sun gear Planetary gear Internal gear Motor Pulsator 1800 r.p.m (60Hz) 1500 r.p.m (50Hz) Gear unit as V.BELT 1 revolution...
5. DIRECTIONS FOR DISASSEMBLY AND ADJUSTMENT BEFORE ATTEMPTING TO SERVICE OR ADJUST ANY PART OF THE WASHING MACHINE, DISCONNECT THE POWER CORD FROM THE ELECTRIC OUTLET. Gear Mechanism Ass'y Replacement GEAR MECHANISM ASSY REPLACEMENT ① ③ Raise the top plate on the outer cabinet. Remove the cap pulsator from the pulsator ass’y by using Loosen four screws mounting outer tub cover and screw driver.
Page 14
⑦ ⑧ Remove the tub I ass’y. Lay the front of the washer on the floor. ⑨ Remove four special bolts of gear protect by using a box wrentch and remove gear protect. ⑩ Remove the V-belt. ⑪ Remove four special bolt of gear mechanism ass’y by ⑫...
MOTOR SYNCHRONOUS AND VALVE REPLACEMENT (NON PUMP MODEL) ① Lay the front of the washer on the floor. ③ Take out the wire of motor synchronous from the braket. ② Loosen two special screw of motor synchronous. ④ Separate the motor synchronous from the base. ⑤...
6. THE REPAIR METHOD OF GEAR MECHANISM FOR CLUTCH SPRING PROBLEM The Structure Of Gear Mechanism ● TOOL FOR REPLACING THE CLUTCH BOSS ASSEMBLE ● i f i o i t y t ’ Fixing jig Ratchet handle Some cotton yarn some THE REPAIR...
How To Check The Clutch Spring Problem PROBLEM 1) THE LAUNDARY IS IN THE SPIN TUB UNEVENLY WHEN JUST STARTING SPIN PROCESS. 2) THEREFORE, IT CAUSE THE SERIOUS NOISE AND VIBRATION WHEN WASHING AND SPINNING PROCESS OR SUPPLING WATER IRREGULARY WHEN SPINNING PROCESS AND CAUSE SHORT OF SPIN PERFORMANCE.
The Process Of Disassemble Disassemble 1 i t o Use wrench or driver - ratchet handle Remove the protector - extension bar - socket : 10mm Release screws marked 4-point. Remove the v-belt. Use fixing jig for pulley as Loosen the fastening nut. to see fig 1 and 17mm-socket for nut.
Page 19
Disassemble 2 i t o Disassemble the pulley. Catch the boss and pull upward with spiral rotate in the Disassemble the clutch boss assembly. clockwise direction. Separate coupling from clutch boss ass’y. Clean the drum plate, coupling surface and contact face between drum plate and cou- pling.
The Process Of Assemble Assemble 1 i t o Check the uneven face of cou- Assemble the coupling. pling is assembled upward. - Push in the clutch boss ass’y with rotating on the clockwise direction. - After assembling, rotate on the clockwise more 2~3 teeth and pull out the pulley shaft upward.
Page 21
Assemble 2 i t o - Use fixing jig and 17mm socket wrench as if disassembling, as fastening torque about 100~200kgf-cm. - Check the end-play, up and downward and check the bind- ing force, too much or not on Assemble the fastening nut. bi-direct of rotation.
REPLACE THE CASE FILTER ASS’Y ② Remove two screws. ③ Remove three screws. ① Separate the back cover from washing machine. ④Turn the case filter ass’y and sepa- ⑤ Separate the drain hose I from the ⑥ Separate the cavitation hose from rate it from the drain motor.
7. TROUBLE SHOOTING GUIDE NOTES 1. When replace the P.C.B. ASS’Y do not scratch the surface of the P.C.B. ASS’Y. 2. Disconnect the power cord from the electric outlet. Concerning Water Supply PROBLEM CHECK POINT CAUSE SOLUTION Do you open the water Open the water tap.
PROBLEM CHECK POINT CAUSE SOLUTION The water inlet valve is Does the water supply Change the water inlet continue while the power defective. valve. is turned off? Does the water supply The triac of P.C.B is Change the P.C.B ASS’Y. start as soon as you press defective.
Concerning Draining PROBLEM CHECK POINT CAUSE SOLUTION Do you install the Install the drain hose Improper installation. drain hose proper- properly. Is the foreign matter Remove the foreign mat- Malfunction of drainage accumulated inside ter from the pump hous- THE WASHER by the foreign matter.
Concerning Spinning PROBLEM CHECK POINT CAUSE SOLUTION Close the lid. Is the lid open? Does the door switch Change the door switch. Door switch is defective. operate normally? Safety switch is defec- Change the safety Does the safety switch tive. switch.
Concerning Operation PROBLEM CHECK POINT CAUSE SOLUTION Is the plug connect-ed Connect the plug. to electric outlet? Is Fuse opended? Change Fuse THE INDICA- Is the condition of Change P.C.B ASS’Y. Power button is defective power button good? LAMPS(L.E.D) DO NOT LIGHT UP WHEN THE Is the connector of the Improper connection of...
8. PRESENTATION OF THE P.C.B ASS’Y Concerning Error Message MESSAGE CAUSE SOLUTION Install drain hose properly. Improper installation of drain hose. Remove foreign matter from drain hose. The drain hose is blocked up by foreign matter. Change drain motor. Drain motor is inferior. Open the water tap.
DWF-415S, 201TRSP SPRAY BASE 3615407831 VALVE INLET AS C+H, AC 220-240V 50/60Hz, 35 3618911300 UNIT CAPACITOR 12.5UF 400VAC, CAN TYPE DWF-315W, 100C, ABS, NON_RINSE 3611132500 CASE DETERGENT 3611132750 DWF-415S, 201TRSP NO RINSE SILVER SPRAY DWF-315W, ABS, 104KR 3614530200 PLATE T...
Page 35
3612507210 GUIDE FILTER AS HIDDEN FILTER (SUS 0.6T) 3616051629 SPECIAL SCREW SUS 430 T2 TRS 5.5*16 3618818410 TUB I DWF-201WSP-MXC 3616051629 SPECIAL SCREW SUS 430 T2 TRS 5.5*16 3616051629 SPECIAL SCREW SUS 430 T2 TRS 5.5*16 3617201200 FLANGE TUB 10kg, 3-FOOT 3616007000 SPECIAL SCREW SCM 24H, 6.5*24...