Connecting The Units - Pioneer GEX-P5750TV Installation Manual

3. TV antenna inputs
Connect from 1 in order.
1. This unit
2. TV antenna (supplied)
6 m
4. Fuse holder
5. Red
4. Fuse holder
5. Red
6. To electric terminal controlled by
the ignition switch (12 V DC) ON/OFF.
7. Black (ground)
7. Black (ground)
8. To vehicle (metal) body.
Fig. 18
1. This unit
3. RCA audio output
(White, Red)
5. To audio inputs
2. RCA video output
(Yellow)
7. Display with RCA
input jacks
Fig. 19
6. To video input
4. RCA cables
(sold separately)

Connecting the Units

Note:
Connection Diagram
• This unit is for vehicles with a 12-volt battery and
negative grounding. Before installing it in a recre-
7 When using this unit as
ational vehicle, truck, or bus, check the battery
voltage.
"SRC : OSD OFF" mode (Fig. 13)
• To avoid shorts in the electrical system, be sure to
1. AV-BUS cable (supplied)
disconnect the ≠ battery cable before beginning
2. AV receiver (e.g. AVH-P5750DVD)
installation.
(sold separately)
• Refer to the owner's manual for details on con-
3. Yellow
necting the other units, then make connections
correctly. 4. Black
• Secure the wiring with cable clamps or adhesive
5. Vehicle Dynamics Processor (e.g. AVG-VDP1)
tape. To protect the wiring, wrap adhesive tape
(sold separately)
around them where they lie against metal parts.
6. Blue
• Route and secure all wiring so it cannot touch any
7. 26-pin cable
moving parts, such as the gear shift, handbrake
(supplied with Vehicle Dynamics Processor)
and seat rails. Do not route wiring in places that
8. IP-BUS cable (supplied)
get hot, such as near the heater outlet. If the insu-
9. To video output
lation of the wiring melts or gets torn, there is a
10. RCA cable (sold separately)
danger of the wiring short-circuiting to the vehicle
body. 11. This unit
• Don't pass the yellow lead through a hole into the
12. Display (e.g. AVD-W8000) (sold separately)
engine compartment to connect to the battery.
13. IP-BUS cable (sold separately)
This will damage the lead insulation and cause a
14. To video 1 input
very dangerous short.
15. To video 2 input
• Do not shorten any leads. If you do, the protection
16. White/Red
circuit may fail to work when it should.
• Never feed power to other equipment by cutting 17. RCA cable (supplied with DVD player)
the insulation of the power supply lead of the unit
18. DVD player (e.g. XDV-P9—) (sold separately)
and tapping into the lead. The current capacity of
19. Multi-CD Player (sold separately)
the lead will be exceeded, causing over heating.
20. Use AV-BUS cable (50 cm) if necessary.
• When replacing fuse, be sure to only use fuse of
the rating prescribed on the fuse holder. 7 When using this unit as
• To prevent incorrect connection, the input side of
"SRC : OSD ON" mode (Fig. 14)
the IP-BUS connector is blue, and the output side
is black. Connect the connectors of the same col- 1. Blue
ors correctly.
2. AV-BUS input
• To minimize noise locate the TV antenna cable,
3. Pioneer head unit (sold separately)
radio antenna cable and RCA cable as far away
4. AV system display (e.g. AVX-P7650)
from each other as possible.
(sold separately)
• Cords for this product and those for other 5. AV-BUS cable (supplied)
products may be different colors even if they
6. Black
have the same function. When connecting this
7. IP-BUS input
product to another product, refer to the sup-
8. This unit
plied manuals of both products and connect
9. IP-BUS cable (supplied)
cords that have the same function.
<ENGLISH>
7 When using this unit as 10.Note
• The position of the parking brake switch
"STAND ALONE" mode (Fig. 15)
depends on the vehicle model. For details,
1. To video 1 input
consult the vehicle Owner's Manual or
2. Display (e.g. AVD-W8000) (sold separately)
dealer.
3. Remote sensor (supplied)
11.Light green
4. RCA cable (sold separately)
Used to detect the ON/OFF status of the
5. To video input parking brake. This lead must be connected
6. Yellow to the power supply side of the parking brake
switch.
7. To rear out (REAR OUT)
12.Power supply side
8. Black
13.Ground side
9. To front out (FRONT VIDEO OUT)
14.Parking brake switch
10. This unit
11. Display unit with RCA input jack
TV antenna connection (Fig. 18)
(sold separately)
Disconnecting an AV-BUS connector
7 When connecting the TV Antenna
(Fig. 16)
(supplied)
1. This unit
When disconnecting an AV-BUS con-
2. TV antenna (supplied)
nector, grasp it firmly on both sides
3. TV antenna inputs
and pull towards you. This will unlock
Connect from 1 in order.
the connector, enabling disconnection.
4. Fuse holder
5. Red
Connecting the power cord (Fig. 17)
6. To electric terminal controlled by the ignition
switch (12 V DC) ON/OFF.
1. This unit
7. Black (ground)
2. Fuse holder
8. To vehicle (metal) body.
3. Yellow
To terminal always supplied with power
Rear display connection (Fig. 19)
regardless of ignition switch position.
4. Fuse resistor
Note:
5. Red
• Output to this product's Rear Display is ON when
(Connect this lead only when this unit is used the Head Unit's source is TV.
as STAND ALONE mode.)
If the Head Unit's source is anything other than
To electric terminal controlled by ignition TV or Head Unit is OFF, pressing POWER button
on the supplied remote control enables you to
switch (12 V DC) ON/OFF.
operate TV independently for the Rear Display.
6. Black (ground)
• Output from this product's rear audio output is
To vehicle (metal) body.
monaural.
7. Connection method
1. This unit
8. Clamp the lead.
2. RCA video output (Yellow)
9. Clamp firmly with needle-nosed pliers.
3. RCA audio output (White, Red)
4. RCA cables (sold separately)
5. To audio inputs
6. To video input
7. Display with RCA input jacks