Table of Contents
Advertisement
Quick Links
QUENTIN™
WIDESPREAD LAVATORY
FAUCET with Speed Connect™ Drain
Congratulations on purchasing your American Standard
faucet with Speed Connect drain, a feature found only
on American Standard faucets.
Speed Connect Drain*
• Fewer parts, installs in less time
• Never needs adjustment
• Guaranteed to seal properly the first time, every time.
*Your new American Standard faucet is designed to work only with the Speed Connect drain.
To ensure that your installation proceeds smoothly-please read these instructions carefully
before you begin.
Recommended tools
Screwdriver
1
INSTALL FAUCET
Seat SEAL (1) into under side of ESCUTCHEON BASE (2).
Feed FAUCET SUPPLIES (3), MOUNTING STUD (4) and DRAIN
CABLE ASSEMBLY (5) through the mounting hole of lavatory or
mounting surface.
From below, push GASKET (6) with RETAINING WASHER (7) onto
MOUNTING STUD (4). Secure Faucet with MOUNTING NUT (8),
pushing faucet to back of sink, so SUPPLIES (3) rests against
mounting hole.
Adjust Faucet so that it is centered. Tighten MOUNTING NUT (8)
to complete faucet mounting.
INSTALLATION
INSTRUCTIONS
7440.801
7440.851
Channel Locks
Turn off hot and cold water
CAUTION
supplies before beginning.
MOUNTING
SURFACE
Adjustable Wrench
74 4 0 . 8 5 1
2
1
GROOVE IN
(FAUCET BASE)
3
1
74 4 0 . 8 01
74 4 0 . 8 5 1
Certified to comply with ANSI A112.18.1
Tubing Cutter
74 4 0 . 8 01
4
6
7
8
5
M 9 6 5 2 3 8
Advertisement
Table of Contents
Related Manuals for American Standard QUENTIN 7440.801
Summary of Contents for American Standard QUENTIN 7440.801
- Page 1 • Never needs adjustment • Guaranteed to seal properly the first time, every time. *Your new American Standard faucet is designed to work only with the Speed Connect drain. To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
-
Page 2: Valve Installation
VALVE INSTALLATION Place RUBBER RING (1) into DECK ADAPTER (2). Install LOCKNUT (3) and RUBBER WASHER (4) onto VALVE BODY (5). From under side of mounting surface, install VALVE BODY (5) through valve mounting hole. Threads of VALVE BODY (5) should extent at least 5/16 of a inch above mounting surface top. - Page 3 POP-UP DRAIN Fig. A. Fig. B. Remove CLEAR PLASTIC COVER (1). Remove CARDBOARD SPACER (2) from under DRAIN DRAIN POP-UP (3). BODY Tighten TAILPIECE (4) on DRAIN BODY before Fig. B. installing DRAIN BODY. REMOVE FLANGE Fig. A. Fig. B. Thread FLANGE (1) counter-clockwise and remove FLANGE (1) and FOAM GASKET (2) from drain Fig.
- Page 4 ATTACH CABLE CONNECTOR Fig. A. Fig. B. Thread CABLE CONNECTOR (1) clockwise onto DRAIN BODY CONNECTION (2) and hand tighten. Fig. A. Your new POP-UP DRAIN installation is now complete. Fig. B. Note: Tailpeice on pop-up drain is 1-1/4” O.D. Fig.
-
Page 5: Care Instructions
TEST INSTALLED FITTING With HANDLES (1) in OFF position, turn on WATER SUPPLIES (2) and check all connections for leaks. Remove AERATOR (3). Operate both HANDLES (1) to flush water lines thoroughly. Replace AERATOR (3). CHECK DRAIN CONNECTIONS Operate POP-UP KNOB (5) and fill Sink with water. Check that DRAIN STOPPER (4) makes a good seal and retains water in Sink. -
Page 6: Cable Adjustment Procedure
Speed Connect™ Drain Troubleshooting Guide If sink does not hold water even though Stopper is in the “down” position: • Follow CABLE ADJUSTMENT PROCEDURE. If Stopper does not raise up fully or sink drains too slowly: • Follow CABLE ADJUSTMENT PROCEDURE. If you need to remove the Stopper: •... - Page 7 Drain so that the Plastic Loop is facing toward the front of the LOGO Sink and the American Standard logo is facing rear. Rotate Stopper slightly if necessary so that the Stopper slides all the way down. Fig. H.
- Page 8 QUENTIN™ WIDESPREAD LAVATORY FAUCET with Speed Connect™ Drain MODEL NUMBER 7440.801 7440.851 M964159-YYY0A HANDLE KIT M964164-YYY0A SPOUT KIT (7440.801) M964163-YYY0A SPOUT KIT (7440.851) M962414-YYY0A ESCUTCHEON KIT 918555-0070A HANDLE SCREW 918049-0070A HANDLE ADAPTER M964156 -YYY0A LIFT ROD & KNOB M922894-YYY0A AERATOR 994053-0070A CARTRIDGE A911903-0070A...