Hilti DD 150?U Operating Instructions Manual
Diamond coring system
Hide thumbs
Also See for DD 150?U:
- Manual (580 pages) ,
- Operating instructions manual (491 pages) ,
- Original operating instructions (100 pages)
Related Manuals for Hilti DD 150?U
Summary of Contents for Hilti DD 150?U
- Page 1 DD 150-U Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...
-
Page 2: Parts Layout
This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02... - Page 3 Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...
- Page 4 Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...
- Page 5 Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...
- Page 6 Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...
- Page 7 Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...
-
Page 8: Table Of Contents
ORIGINAL OPERATING INSTRUCTIONS DD 150‑U diamond coring system Type identification plate It is essential that the operating instructions ¡ Interface plate are read before the machine is operated for Connector screws (water swivel / suction head) the first time. Cover (water swivel / suction head) Suction hose connector Always keep these operating instructions to- Chuck... -
Page 9: General Information
Wheel assembly Various accessories 3 Rota-Rail Switch lock for drill stand operation Jack screw Vacuum base plate — 1 General information Obligation signs 1.1 Safety notices and their meaning DANGER Draws attention to imminent danger that will lead to serious bodily injury or fatality. WARNING Wear eye Wear a hard... -
Page 10: Description
Drilling into materials that produce electrically conductive dust (e.g. magnesium) is not permissible. Where possible, use a suitable industrial vacuum cleaner when working with the system, e.g. the Hilti VC 20‑U/UM, VC 40‑U/UM or VC 60‑U. - Page 11 Drilling into materials hazardous to the health (e.g. asbestos) is not permissible. DANGER Use only the genuine Hilti accessories or ancillary equipment listed in the operating instructions. Use of accessories or ancillary equipment not listed in the operating instructions may present a risk of personal injury.
- Page 12 2.6 Items supplied as standard Machine Operating instructions Hilti toolbox or cardboard box 2.7 Using extension cords Use only extension cords of a type approved for the application and with conductors of adequate gauge. Recommended minimum conductor gauge (cross section) and max. cable lengths...
-
Page 13: Accessories
NOTE Switching other machines or appliances on and off can cause undervoltage and/or overvoltage peaks which could damage the machine. Never operate other machines from the generator/transformer at the same time. 3 Accessories Designation Short designation Description TPS theft protection system with Option company card, company remote and TPS‑K key... -
Page 14: Safety Instructions
5 Safety instructions protection used for appropriate conditions will reduce 5.1 General Power Tool Safety Warnings personal injuries. c) Prevent unintentional starting. Ensure the switch WARNING is in the off‐position before connecting to power Read all safety warnings and instructions. Failure source and/or battery pack, picking up or carrying to follow the warnings and instructions may result the tool. - Page 15 tating drill bits, discs or blades, etc. may lead to 5.1.5 Service injury. a) Have your power tool serviced by a qualified repair k) When using the equipment, always lead the supply person using only identical replacement parts. cord, the extension cord and the water hose (if This will ensure that the safety of the power tool is applicable) away from the machine to the rear.
-
Page 16: Before Use
5.3.5 Personal protective equipment a specially-prepared supply cord available from Hilti Customer Service. Check extension cords at regular intervals and replace them if found to be damaged. Do not touch the supply cord or exten- sion cord if damaged while working. - Page 17 Pull the locking pin out of the slot. NOTE Pivot the machine away from the drill stand. Hilti M12 or M16 metal expansion anchors are usually suitable for fastening diamond core drilling equipment to 6.1.7 Fastening the drill stand by vacuum 14 uncracked concrete.
- Page 18 6.1.11 Fitting the water connection 19 DANGER CAUTION To avoid injury, use only genuine Hilti core bits and Regularly check the hoses for damage and make sure DD 150-U accessories. If using a machine with a BI+ that the maximum permissible water supply pressure chuck, only genuine Hilti core bits may be used with of 6 bar is not exceeded.
-
Page 19: Operation
Set the switch to the correct position according to CAUTION the core bit diameter used (see Section 2.3). When The core bit may become hot during use or during sharp- turning the switch, rotate the core bit by hand at the ening. - Page 20 Switch the machine off by releasing the on / off using genuine Hilti spare parts. switch and then wait until the core bit has stopped Press the “I” or “Reset” button on the ground fault rotating (optional operation).
- Page 21 Bring the side handle into the desired position and Press the on / off switch on the machine. secure it (see Section 6.1.1). When beginning drilling, apply only light pressure Fit the hole-starting aid (optional operation). until the core bit has centered itself and then in- crease the pressure.
- Page 22 When beginning drilling, apply only light pressure If a water extraction system (vacuum cleaner) is until the core bit has centered itself and then in- used, switch it on. crease the pressure. Drill to a depth of 3-5 mm to Secure the side handle in the desired position.
- Page 23 Release the Rota-Rail fastening screw and pivot the WARNING machine with the Rota-Rail to the left or right to Stop working if the vacuum removal system no longer provide access to the hole being drilled. functions. Remove the core or change the core bit. Pivot the machine back to its original position, WARNING tighten the Rota-Rail fastening screw securely and...
-
Page 24: Care And Maintenance
Clean the chuck and the clamping segments with a Close the carbon brush covers on the left-hand and cloth at regular intervals and lubricate the parts with Hilti right-hand side of the motor and tighten the retaining lubricant spray. Remove any particles of foreign matter screws. -
Page 25: Troubleshooting
The diamond core bit is polished. The wrong type of core bit has been used. Seek advice from Hilti. Water pressure / flow rate too high. Reduce the water flow rate by adjust- ing the flow regulator. -
Page 26: Disposal
10 Disposal Most of the materials from which Hilti machines or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back old machines and appliances for recycling. -
Page 27: Manufacturer's Warranty
From the environmental and health point of view, the disposal of drilling dust can be problematic. Ask the local public authorities for information about current regulations. 11 Manufacturer’s warranty Hilti warrants that the tool supplied is free of defects in Additional claims are excluded, unless stringent na- material and workmanship. This warranty is valid so long tional rules prohibit such exclusion. - Page 28 Tel.: +423 / 234 21 11 Fax:+423 / 234 29 65 www.hilti.com Hilti = registered trademark of Hilti Corp., Schaan W 3982 | 0513 | 00-Pos. 3 | 1 Printed in Germany © 2013 Right of technical and programme changes reserved S. E. & O 434950 / A3 Printed: 08.07.2013 | Doc-Nr: PUB / 5069533 / 000 / 02...