Special Functions; Control Lock; Clean Washer; My Cycle - Kenmore 796.4128 Series Use & Care Manual

SPECIAL FUNCTIONS

CONTROL LOCK

Use this option to disable the controls.
The washer can only be locked during
a cycle. This feature can prevent
children from changing cycles or
operating the machine. Once set, the controls remain locked
and must be turned OFF before the controls can be used
again. Once the washer has shut off , the power button will
allow the machine to be turned ON, but the controls will still
be locked. When the controls are locked, the DELAY START
LED will illuminate and "CL" will display alternately with the
estimated time remaining.
Press and hold the EXTRA RINSE button for fi ve seconds to
activate or deactivate the controls.

CLEAN WASHER

Detergent residue can build up in the
wash drum over time and can lead to a
mildewy or musty smell. The CLEAN
WASHER cycle is specially designed to
remove this buildup using bleach or another cleaner designed
specifi cally for cleaning front load washers. Run the CLEAN
WASHER cycle once a month, or more often under heavy use
conditions or if odor is present. See complete instructions in the
CARE AND CLEANING section.
Turn ON the washer and press the CLEAN WASHER
1
button. Selecting any other cycle after CLEAN WASHER
has been selected will cause the CLEAN WASHER cycle
to be cancelled.
2
Fill the bleach dispenser to the MAX line with liquid
chlorine bleach. Do not overfi ll the bleach dispenser.
Overfi lling will cause the bleach to dispense immediately.
NOTE: For other drum cleaning products, follow
the cleaner manufacturer's instructions and
recommendations. For powdered cleaning products,
add the cleaner to the main wash compartment of
the dispenser drawer. Place tablet cleaners directly
into the drum.
3
Press the START/PAUSE button to start the cycle.
4 After the cycle has ended, keep the door ajar. This will
promote air circulation and allow the interior of the
machine to dry. To use this feature, close the door just
until it contacts the door magnet.
NOTE: Do NOT use this cycle with clothes, and do
NOT add detergent or fabric softener.

MY CYCLE

other options for a cycle, and then recall them at the touch
of a button.
NOTE: You can only save a setting for one cycle at a
time. Pressing and holding the MY CYCLE button will
overwrite any previously saved cycle.
To save a MY CYCLE:
1
Press the POWER button to turn on the washer.
2
Turn the cycle selector knob to select the desired cycle.
3
Press the CYCLE MODIFIER button to change the desired setting.
4
Press the CYCLE OPTION button to add the desired options.
Press and hold the MY CYCLE button.
5
To recall a MY CYCLE:
1
Press the POWER button to turn on the washer.
2
Press the MY CYCLE button. The stored settings will be
displayed.
Press the START/PAUSE button to start the cycle.
3
NOTE: MY CYCLE can be adjusted the same as any
other cycle. However, once any other button is pressed,
the LED will turn off indicating that the settings are no
longer those of your saved cycle.

AUTO SOAK

presoak prior to the start of the selected cycle. At the
end of the presoak time, the selected cycle will use the
same water.
To use the AUTO SOAK feature, press and hold the
STEAM TREAT button for fi ve seconds.

STAY FRESH

STAY FRESH option will tumble clothes intermittently through
the drum for up to eight hours.
To select the STAY FRESH option, press and hold the CLEAN
WASHER button for approximately fi ve seconds. Press the
POWER button or the START/PAUSE button to remove
clothes at any time.
23
HOW TO USE
MY CYCLE allows you to store a
customized wash cycle for future use.
It allows you to save favorite
temperature, spin speed, soil level, and
Use the AUTO SOAK option to
presoak garments to help remove
diffi cult spots or stains on fabric.
This option provides a 30 minute
The STAY FRESH option helps keep
wrinkles from setting in clothes if they
are not removed from the washer as
soon as the cycle is complete. The