Yaesu VX-6E Operating Manual page 90

S M
ET ENU
S M I F
ET ODE TEM UNCTION
1 [ APO ]
Setting of the Automatic Power-Off feature.
2 [ AR BEP ]
Selects the Beep option during ARTS operation.
3 [ AR INT ]
Selects the Polling Interval during ARTS operation.
4 [ ARS ]
Enables/Disables the Automatic Repeater Shift function.
5 [ ATT ]
Enables/Disables the Receiver Front-end (10 dB) Attenuator.
6 [ BCLO ]
Enables/Disables the Busy Channel Lock-Out feature.
7 [ BEEP ]
Enables/Disables the keypad beeper.
8 [ BELL ]
Selects the number of CTCSS/DCS Bell ringer repetitions.
9 [ BP LVL ]
Adjust the Beep volume level.
10 [ BNK NM ]
Stores Alpha-Numeric "Tags" for the Memory Group.
11 [ BSY.LED ]
Enables/Disables the BUSY LED while the Squelch is open.
12 [ CH CNT ]
Selects the Channel Counter Search Width.
13 [ CLK.SFT ]
Shifting of the CPU clock frequency.
14 [ CW ID ]
Programs and activates the CW Identifier (used during ARTS op-
eration).
15 [ CWTRNG ]
Enables/Disables the CW Training feature and selects the sending
speed of the Morse Code.
16 [ DC VLT ]
Indicates the DC Supply Voltage.
17 [ DCS CD ]
Setting of the DCS code.
18 [ DCS RV ]
Enables/Disables "Inverted" DCS code decoding.
19 [ DIMMER ]
Setting of the Display brightness level.
20 [ DMR.WRT ]
Enables/Disables over-written the Direct Memory Recall Channel
while operating on the Direct Memory Recall Channel.
21 [ DT A/M ]
Enables/Disables the DTMF Autodial feature.
22 [ DT SET ]
Programming of the DTMF Autodialer.
23 [ EAI ]
Enables/Disables the Emergency Automatic ID (EAI) Feature.
24 [ EAI.TMR ]
Setting of the Emergency Automatic ID (EAI) operating mode and
its Transmit Time.
25 [ EDG.BEP ]
Enables/Disables the Band-edge beeper while selecting the fre-
quency via the DIAL knob.
26 [ EMG S ]
Selects the alarm(s) utilized when the Emergency function is en-
gaged.
27 [ HLF.DEV ]
Reducing the Deviation level by 50 %.
28 [ HM/RV ] Selects the Primary function of the [ HM/RV ( EMG ) R/H ] key.
29 [ INT CD ]
Selects the Access Number (DTMF digit) for WIRES
30 [ INT MD ]
Selects the Internet Link Connection mode.
31 [ INT.A/M ]
Enables/Disables DTMF Autodialer feature while operating on the
Internet Connection feature.
32 [ INT.SET ]
Selects the memory register for an Access Number (DTMF code)
for non-WIRES™ Internet Link System access.
33 [ LAMP ]
Selects the LCD/Keypad Lamp mode.
34 [ LED LT ]
Illuminates the STROBE glows continuously in white.
35 [ LOCK ]
Selects the Control Locking lockout combination.
36 [ M/T-CL ]
Selects the MONI/T.CALL switch (just below the PTT switch)
function.
37 [ MCGAIN ]
Adjust the microphone gain level.
38 [ MW MD ]
Selects the method of selection of channels for Memory Storage.
39 [ NAME ]
Toggles the display indication between "frequency" and the
channel's "Alpha/Numeric Tag."
40 [ NM SET ]
Stores Alpha-Numeric "Tags" for the Memory channels.
88
M
ODE
A
VAILABLE
( D
EFAULT
OFF / 30MIN / 1HOUR / 3HOUR
/ 5HOUR / 8HOUR
IN RNG / ALWAYS / OFF
25 SEC / 15 SEC
ON / OFF
OFF / ON
OFF / ON
ON / OFF
OFF / 1 / 3 / 5 / 8 /
CONT (Continuous ringing)
LVL 1 - LVL 9 (LVL 5)
ON / OFF
±5 MHz / ±10 MHz /
±50 MHz / ±100 MHz
OFF / ON
4WPM-13WPM / 15WPM /
17WPM / 20WPM / 24WPM /
30WPM / 40WPM
(20CPM-65CPM (5CPM multiples) /
75CPM / 85CPM / 100CPM /
120CPM / 150CPM / 200CPM)
104 standard DCS codes (023)
DISABLE / ENABLE
LVL 0 - LVL 12 (LVL 7)
OFF / ON
MANUAL / AUTO
OFF / ON
INT. 1M through INT.10M /
INT.15M / INT.20M / INT.30M /
INT.40M / INT. 50M
CON. 1M through CON.10M /
CON.15M / CON.20M / CON.30M /
CON.40M / CON. 50M (CON.5M)
OFF / ON
BP+STR / BEAM / BP+BEM / CW /
BP+CW / BEEP / STROBE
OFF / ON
REV / HOME
operation. DTMF 1 - DTMF F
SRG / FRG
MANUAL / AUTO
KEY / CONT / OFF
KEY / DIAL / K+D / PTT /
P+K / P+D / ALL
MONI / T-CALL
LVL 1 - LVL 9 (LVL 5)
NEXT / LOWER
FREQ / ALPHA
VX-6R/E O
PERATING
V
ALUES
)
: B I
OLD TALIC
---
---
OFF /
---
---
---
---
1
--
M
ANUAL