Recording Cannot Be Done; The Connect An Ld Player Via An Rf Demodulator; The Fm Reception Is Poor; Radio Stations Cannot Be Tuned In - Sony STR-DB1070 Operating Instructions Manual

Hide thumbs Also See for STR-DB1070:
Table of Contents

Advertisement

Recording
cannot
be done.
l
Check that the components
are connected
correctly.
l
Select the source component
with FUNCTION
control.
l
When recording
from a digital component,
make
sure the INPUT
MODE
is set to ANALOG
2CH
FIXED
(see page 26) before recording
with a
component
connected
to the analog MD/DAT
or
TAPE terminals
(STR-DB
1070) or the analog
MD/TAPE
terminals
(STR-DB870).
l
When recording
from a digital component,
make
sure the INPUT MODE
is set to COAXIAL
FIXED
or OPTICAL
FIXED
(see page 26)
before recording
with the component
connected
to the DIGITAL
MD/DAT
OUT terminals
(STR-DB
1070) or the DIGITAL
MD/TAPE
OUT terminals
(STR-DB870).
To connect
an LD player
via an RF demodulator.
l
Connect the LD player to the RF demodulator,
then connect the RF demodulator's
optical or
coaxial digital output to the receiver's
DVDiLD
OPTICAL
IN or COAXIAL
jack. When making
this connection,
be sure to set INPUT
MODE
manually
(see page 26). The receiver
may not
operate correctly
if INPUT
MODE
is set to
AUTO
2CH.
For details on DOLBY
DIGITAL
RF hookups,
see the operating
instructions
supplied with your
RF demodulator.
The FM reception
is poor.
l
Use a 75ohm
coaxial cable (not supplied) to
connect the receiver to an outdoor FM antenna as
shown below. If you connect the receiver
to an
outdoor antenna, ground it against lightning.
To
prevent a gas explosion,
do not connect the
ground wire to a gas pipe.
Receiver
Outdo0
Ground wire
(not supplied)
+
To ground
Radio stations
cannot
be tuned
in.
l
Check that the antennas are connected
securely.
Adjust the antennas and connect an external
antenna if necessary.
l
The signal strength of the stations is too weak
(when tuning in with automatic
tuning). Use
direct tuning.
l
Make sure you set the tuning interval correctly
(when tuning in AM stations with direct tuning).
l
No stations have been preset or the preset
stations have been cleared (when tuning by
scanning preset stations).
Preset the stations (see
page 40).
l
Press DISPLAY
so that the frequency
appears in
the display.
RDS does
not work.'
l
Make sure that you're tuned to an FM RDS
station.
l
Select a stronger FM station.
The RDS information
that you want does
not
appear.*
l
Contact the radio station and find out whether or
not they actually provide
the service in question.
If so, the service may be temporarily
out of
order.
5 Ia
There
is no picture
or an unclear
picture
appears
t
on the TV screen
or monitor.
l
Select the appropriate
function
on the receiver.
5
l
Set your TV to the appropriate
input mode.
a
l
Move your TV away from the audio components.
3
P)
The remote
does
not function.
f:
l
(For STR-DB870
area code U, CA)
:
The 2ND ROOM
button and the ON SCREEN
button on the remote are not available.
l
Point the remote at the remote sensor
q
on the
receiver.
l
Remove any obstacles
in the path between the
remote and the receiver.
l
Replace both batteries in the remote with new
ones, if they are weak.
l
Make sure you select the correct function
on the
remote.
l
If the remote is set to operate the TV only, use
the remote to select a source or component
other
than TV before operating
the receiver
or other
component.
* Models of area code CEL only
51

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Str-db870

Table of Contents