Table of Contents
Advertisement
Quick Links
7" SANDER/ POLISHER
WITH DIGITAL DISPLAY
Model 90820
ASSEMBLY AND OPERATING INSTRUCTIONS
®
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
©
®
Copyright
2003 by Harbor Freight Tools
. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
Advertisement
Table of Contents
Related Manuals for Chicago Electric 90820
Summary of Contents for Chicago Electric 90820
- Page 1 7” SANDER/ POLISHER WITH DIGITAL DISPLAY Model 90820 ASSEMBLY AND OPERATING INSTRUCTIONS ® 3491 Mission Oaks Blvd., Camarillo, CA 93011 Visit our Web site at: http://www.harborfreight.com © ® Copyright 2003 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
-
Page 2: General Safety Rules
Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. Protect others in the work area from debris such as dust and sparks. Provide respirators, barriers, or shields as needed. SKU 90820 Page 2... -
Page 3: Electrical Safety
Power Switch on, invites accidents. Remove adjusting keys or wrenches before turning the power tool on. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury. SKU 90820 Page 3... -
Page 4: Tool Use And Care
When servicing a tool, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SKU 90820 Page 4... -
Page 5: Specific Safety Rules
(California Health & Safety Code 25249.5, et seq.) People with pacemakers should consult their physician(s) before using this product. Operation of electrical equipment in close proximity to a heart pacemaker could cause interference or failure of the pacemaker. SKU 90820 Page 5... -
Page 6: Grounded Tools: Tools With Three Prong Plugs
Your tool must be plugged into an appropriate outlet, properly installed and grounded in accordance with all codes and ordinances. The plug and outlet should look like those in the following illustration. (See Figure A.) FIGURE A SKU 90820 Page 6... -
Page 7: Extension Cords
(See Figure C.) If you are using one extension cord for more than one tool, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Figure C.) SKU 90820 Page 7... - Page 8 * Based on limiting the line voltage drop FIGURE C to five volts at 150% of the rated amperes. SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current Amperes No Load Revolutions xxxx/min. per Minute (RPM) SKU 90820 Page 8...
-
Page 9: Assembly Instructions
NOTE: Avoid using too much wax. For additional applications of wax to the Foam Bonnet, reduce the amount of wax. The Foam Bonnet will not absorb as much wax in subsequent applications. REV 06/05 SKU 90820 Page 9... - Page 10 Backing Pad (41). (Similar to Figure F.) Plug the Power Cord (1) of the Polisher into the electrical extension cord. Then, plug the extension Speed Speed cord into the grounded, 120 volt, electrical outlet. Down Figure G SKU 90820 Page 10...
- Page 11 Grip the Sander/Polisher firmly with both hands. Then turn the Power Switch (6) to its “ON” position, select the desired speed, and allow the Backing Pad (41) to rotate until it has reached that speed. (See Figure G.) SKU 90820 Page 11...
- Page 12 The Bonnets (42, 43) may be machine washed in cold water with detergent. Then hang dry. Use only a clean cloth and mild detergent to clean the body of the Polisher. Do not use solvents. Do not immerse any part of the tool in liquid. SKU 90820 Page 12...
-
Page 13: Please Read The Following Carefully
BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. SKU 90820 Page 13... -
Page 14: Assembly Diagram
Assembly Diagram Part 43 (Foam Bonnet) not shown. NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 90820 Page 14...