Technical Specifications; Hard Wiring Details - Electrolux EOEM61CS User Manual

34 technical specifications electrolux e:line ovens

Technical specifications

model product dimensions
(h x w x d) mm
EOEM61CS 595 x 596 x 573
EOEE62CS 595 x 596 x 573
EOEE62CK 595 x 596 x 573
EOEE63CS 595 x 596 x 573
EUEE63CS, EUEE63CK 888 x 596 x 573
EDEE63CS 1081 x 596 x 573
EPEE63CS, EPEE63CK 595 x 596 x 573
error code description
F01 or 01 Door lock sensor alarm
F02 or 02 Door lock actuator alarm
F04 or 04 Oven Probe (PT500) out of
range alarm
F05 or 05 Oven Probe (PT500) too high
temperature alarm
25 Board Temperature Sensor
(NTC) too high temperature
alarm
26 Board Temperature Sensor
(NTC) out of range warning
6 Board Temperature Sensor
(NTC) out of range alarm
F08 or 08 Communication alarm
F09 or 09 Software compatibility code
alarm
C1 Telescopic runners fitted
C3 Door open
F03 or 03 EEPROM check sum alarm
F14 or 14 EEPROM compatibility code
alarm
electrical connection min. fuse max. power
rating rating
230-240v/50Hz 16A 3.1kW
230-240v/50Hz 16A 3.1kW
230-240v/50Hz 16A 3.1kW
230-240v/50Hz 16A 3.1kW
230-240v/50Hz 25A 5.3kW
230-240v/50Hz 25A 5.8kW
230-240v/50Hz 16A 3.1kW
comment fix
This relates to a door lock Check wiring/plugs or
failure which is only associated replace door lock
with the Pyro product
This relates to the temperature Replace probe
sensing probe which may be
out of tolerance, or have open/
short circuit connections
This relates to the temperature Cooling fan not working
of the powerboard and/or the or replace powerboard
temperature-sensing element
(NTC) on the powerboard
This relates to an error in Reset power. (Minimum of
communication between 20 sec.) or check or replace
the powerboard and the IOI data cable
controller. This can occur if
the IOI controller is connected
while the powerboard is
energised
This relates to a mismatch Replace Powerboard
between powerboard firmware
version and the IOI controller
firmware version. Most likely
caused by an un-programmed
powerboard
Only applies to Pyro product Remove both side racks and
re-start pyro cycle
Only applies to Pyro product Close door and restart pyro
cycle
Relates to the controller Replace Controller
Relates to the controller Replace Controller
Technical specifications
Other Potential complaints
max.
• W hen the door is opened the fan stops (underbench
current
only) This is a function of the powerboard to help reduce
rating
the blast of air the customer receives when they open
12.9A
the door.
12.9A • W hen a non-fan mode is selected the fan starts. Most
oven modes have a fast heat up function that uses the
12.9A
fan, fan element, and top (boost) element. Auto fast
12.9A
heat up can be overridden by selecting a temperature
22.1A of 120ºC or less, allowing the function to start, then
increasing the temperature to the desired level.
24.2A
• T he light stays on when the door is closed, does not
12.9A
turn on when the door is open and the oven is off.
The door switch is not activating due to restricted
travel or broken actuator.
Test Mode
• W ithin 10 seconds of powering up simultaneously press
the timer button and start/stop time '+' button, this will
enter 'TEST MODE' for a maximum of 5 minutes.
Firstly displayed will be the software version and model
No. Then using the function ' ^ ' and 'v' buttons scroll
through door lock test (Pyro only) individual element and
light, cooking fan, cooling fan and temperature probe
etc. functions.
technical specifications electrolux e:line ovens 35

Hard wiring details

1. Remove terminal cover plate from rear panel of appliance.
2. Fit wires through hole in cover plate and make
connections to terminals.
3. Engage wires into plastic clip. Secure plastic clip with
two long silver screws (supplied in separate bag).
4. Replace cover plate onto rear panel.
Plastic clips
Plastic clip
securing points
Note:
• Double Oven (Model EDEE63CS)
This product is to be wired through the bottom access
panel only.