Peavey IPR 1600 Operating Manual page 33

Rated Power (2 x 2 ohms)
Rated Power (2 x 4 ohms)
Rated Power (2 x 8 ohms)
Rated Power (1 x 2 ohms)
Rated Power (1 x 4 ohms)
Rated Power (1 x 8 ohms)
Minimum Load Impedance
Maximum RMS Voltage Swing
Frequency Response
T.H.D. (2 x 2 ohms)
T.H.D. (2 x 4 ohms)
T.H.D. (2 x 8 ohms)
Input CMRR
Voltage Gain
Crossover
Crosstalk
Hum and Noise
Slew Rate
Damping Factor (8 ohms)
Phase Response
Input Sensitivity
Input Impedance
Current Draw @ 1/8
Current Draw @ 1/3
Cooling
Controls
Indicator LEDs
Protection
Connectors
Construction
Dimensions
Net Weight
Gross Weight
Warranty
Rated power readings made with BW: <10 Hz to 22 kHz. All power measurements made at 120 VAC and 240VAC.
2 ohm power is time limited by circuit breaker.
*Net Weight does not include power cord.
IPR-3000 Specification Sheet
- 1,490 watts per channel @ 1 kHz 1% T.H.D. both channels driven.
- 840 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 440 watts per channel @ 1 kHz at <0.1% T.H.D. both channels driven.
- 1,640 watts @ 1 kHz at <0.1% T.H.D.
- 930 watts @ 1 kHz at <0.1% T.H.D.
- 470 watts @ 1 kHz at <0.1% T.H.D.
- 2 ohms
- 71 volts
- 20 Hz - 60 kHz; -0.4 dB, -3.0 dB at 1 watt.
- <0.1% @ 1,350 watts per channel from 20 Hz to 4 kHz, decreasing to 1,150 watts at 20 kHz.
- <0.1% @ 820 watts per channel from 20 Hz to 20 kHz.
- <0.1% @ 430 watts per channel from 20 Hz to 20 kHz.
- > - 76 dB @ 1 kHz
- x 75 (+37dB)
nd
- 100 Hz switchable 2 order High pass and 3
- > -68 dB @ 1 kHz at 100 watts power @ 4 ohms.
- > -101.5 dB, "A" weighted referenced to rated power @ 4 ohms.
- > 12V/s
- > 215:1 @ 20 Hz - 1 kHz at 8 ohms
- +23 to -70 degrees from 20Hz to 20kHz
- 0.775 volts +/- 3% for 1 kHz 4 ohm rated power, 0.730 volts +/- 3% for 1 kHz. 2 ohm rated power
- 15k ohms, balanced and 7.5k ohms unbalanced.
- 917 watts @ 2 ohms, 618 watts @ 4 ohms, 353 watts @ 8 ohms
- 2,016 watts @ 2 ohms, 1,236 watts @ 4 ohms, 662 watts @ 8 ohms
- Temperature dependent variable speed 80 mm DC fan
- 2 front panel attenuators, crossover select switch for H.P.F, Normal and L.P.F.
- 2 DDT (clip limiting), 2 Signal presence, 2 Active status, 2 Temp and 2 DC protect
- Thermal, DC, subsonic, incorrect loads, under and over voltage
- Inputs: Dual Combination 1/4" XLR, Outputs: Dual 1/4" signal patch, dual 4-pin twist-lock connectors
- 0.062" thick aluminum
- 3.5"x19"x 10.5" behind front panel + 0.6" for handle
- 3.40 kg (7.5 lbs.*)
- 4.54 kg (10 lbs.)
- 5 years
rd
order Low Pass per channel.
33