Table of Contents
Advertisement
Touch Screen reMoTe conTrol operaTIon
1. Press the ON/up button to turn on the fireplace. The
flame icon on the LCD displays
High.
2. Press the OFF/down button to
decrease the flame height and
turn off the fireplace. When the
OFF/down button is pressed
for three times, the flame icon
changes form High to Medium,
to Low, then to Off.
3. If the OFF button is held for
more than 3 seconds at any
flame height, the fireplace will
be turned off and the flame icon
disappears.
4. Sliding up and down on the ar-
row buttons can also turn on or turn off the fireplace.
5. If the fireplace is shut off using the above methods in 3
and 4, all the settings will be remembered and will be
resumed next time the fireplace is turned on (Memory
Off).
Timer Mode
Figure 52
Press the TIMER button to enter
timer mode. The fireplace will stay
on for a period of time as specified
by the timer and then be shut off
by the transmitter when the timer
counts down to zero.
1. When the TIMER button is
pressed, the Set Time appears
in the frame of the button and
flashes.
2. Use ON/up and OFF/down to
increase or decrease the Set
Time in 15 min. increments, between 0:00 to 6:00.
Sliding up and down on the arrow buttons will increase
or decrease the Set Time in 1 hour increments.
3. Push the TIMER button again to confirm the Set Time,
the transmitter sends an ON signal to turn on the fire-
place.
4. The flashing stops and the ON/up and OFF/down but-
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
5. The TIMER button can be used when the transmit-
ter is in Manual Mode or in Thermostat Mode. In both
modes, the fireplace will be shut down completely
when the timer counts down to zero.
6. To exit Timer Mode,
a. Push and hold the TIMER button for 3 seconds Or
b. Use the OFF/down buttons to decrease the Set
Time to zero Or
73D4125
Thermostat Mode
Figure 53
Press the THERMO button to
set the transmitter in thermostat
mode. The transmitter will au-
tomatically turn on the fireplace
when the room temperature is
below the set temperature and
turn off the appliance when the
room temperature is above the
set temperature within one de-
gree.
1. When the THERMO button is
Figure 51
FP2651
Manual mode
2. Use ON/up and OFF/down to increase or decrease
3. Press the THERMO button again to confirm the Set
4. The flashing stops and the ON/up and OFF/down but-
5. To exit Thermostat Mode:
Figure 52
FP2652
Timer mode
Smart Mode option for Thermostat Mode
Figure 54
Press and hold the THER-
MO button and the ON/UP
button at the same time for
3 seconds to toggle be-
tween Smart Mode and the
regular Thermostat Mode.
The icon "Smart Mode" will
appear under the Set Tem-
perature. The transmitter
will automatically adjust the
flame height according to
the difference between the
Set temperature and the
Room temperature. There
c. Slide down on the arrow buttons to exit TIMER
mode and shut off the fireplace.
pressed, the Set temperature
appears in the frame of the
button and flashes.
the Set temperature in 1 degree increments, between
45 degrees and 90 degrees. Slide up and down on the
arrow buttons will increase or decrease the Set Tem-
perature in 10 degrees increments.
Temperature. The transmitter will send out an On
signal or an Off signal depending on the relationship
between the Set temperature and the Room tempera-
ture.
tons become flame height controller again. The flame
height will then stay as set up by the ON/up and OFF/
down buttons.
a. push and hold the THERMO buttons for 3 sec-
onds or
b. slide down on the arrow buttons to exit Thermo-
stat mode and shut off the fireplace.
KSTDV Series Gas Fireplace
Figure 53
FP2653
thermo mode
Figure 54
FP2654
smart mode
Smart
Mode
Icon
39
Advertisement
Table of Contents
