Table of Contents
Advertisement
When a pair of the M700/5's main channels
are bridged, they will deliver 200W x 1 into a
4 ohm load or 150W x 1 into an 8 ohm load.
Operating a pair of bridged channels into a
load lower than 4 ohms is not recommended.
A bridged pair of channels requires that both
channels in the pair receive input. You must
connect the mono or stereo source signal to
both the left and right inputs the bridged
channel pair. Connection of only one input will
result in reduced power output, increased
distortion and can cause the amplifier to
overheat. Do not do this!
When a pair of the M700/5's main channels
are operating in bridged mode, the output will be
in mono (only one channel). This mono channel
can contain only right channel information, only
left channel information, or the sum of the signals
from right and left input channels. In order to
achieve one of these options, configure the inputs
to that pair of channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only
or right-only signal to a pair of the M700/5's
channels you must use a "Y-Adaptor" to split
the single channel signal into both left and
right RCA inputs of the bridged channel
pair. This option is used when deploying a pair
of the M700/5's main channels to drive left
channel speakers only and the other pair of the
M700/5's main channels to drive right channel
speakers only.
2) Left + Right Channel Information: When
bridged and fed by a stereo source signal, a
bridged pair of the M700/5's channels will
automatically combine the left and right input
signals into a summed mono (left + right)
input signal.
10 | JL Audio - M700/5 Owner's Manual
subwooFer outPuts
The M700/5's single subwoofer channel is
designed to deliver power into subwoofer loads
equal to or greater than 2 ohms. It is rated for
300W into 2 ohms, 250W into 3 ohms and 200W
into 4 ohms (Continuous Power, RMS Method).
Subwoofer loads below 2 ohms nominal are not
recommended and may cause the amplifier
to initiate a protection mode which reduces
power output.
The M700/5's subwoofer outputs are designed
to accept 16 AWG - 8 AWG wire. To connect
the subwoofer wires to the amplifier, first back
out the set screws on the top of the terminal
block, using the supplied 2.5 mm hex wrench.
Strip 1/2 inch (12 mm) of insulation from the
end of each wire and insert the bare wire into
the terminal block, seating it firmly so that no
bare wire is exposed. While holding the wire
in place, tighten the set screw firmly, taking
care not to strip the head of the screw.
You will notice that there are two "+" positive
connections and two "–" negative connections.
This is to facilitate multiple subwoofer wiring.
The two positive and two negative connections
are connected in parallel inside the amplifier
They are not stereo outputs. Connecting two
subwoofers, each to one set of positive and
negative terminals, will result in a parallel
subwoofer connection. If only connecting one
pair of subwoofer wires, it is not necessary to use
both sets of connections.
status led / ProteCtion CirCuitrY
There is a single multi-color LED on the top
surface of the amplifier to indicate the amplifier's
operating status.
1) Flashing Green: amplifier is powering up,
audio output is muted.
2) Constant Green: amplifier is on and
functioning normally, audio output is active.
3) Constant Red: Indicates that the amplifier has
exceeded its safe operating temperature, putting
the amplifier into a self-protection mode, which
reduces the peak power output of the amplifier.
When its temperature returns to a safe level, the
red light will return to green and the amplifier
will return to full-power operating mode.
4) Constant Amber (yellow): Indicates that
an over-current condition has occurred and
is accompanied by a muting of the affected
channel(s). Because the muting behavior may be
very short in duration, it may manifest itself as
an audible, repetitive ticking noise in the output.
Over-current conditions can be caused by a
speaker impedance lower than the optimum load
impedance range for the amplifier or a short-
circuit in the speaker wiring. The latter can result
from a short circuit between the positive and
negative speaker wires or between either speaker
wire and a power wire. The "Status LED" will
remain amber for a few seconds, even if the over-
current condition is of a very short duration.
This functionality can be used to diagnose a
short-circuit by only connecting one channel at
a time. The "Status LED" will turn amber when
you connect the channel that is experiencing the
problem and turn the volume up.
5) LED off / Amplifier Shuts Off Unexpectedly
The only condition that will shut down
an undamaged M700/5 completely is if battery
voltage or remote turn-on voltage drops below
10 volts. The "Status LED" will turn off when
this occurs. The amplifier will turn back on
when voltage climbs back above 11 volts. If this
is happening in your system, have your charging
system and power wiring inspected.
For more information on troubleshooting this
amplifier, refer to Appendix D (pages 16, 17).
serViCing Your Jl audio amPliFier
If your amplifier fails or malfunctions, please
return it to your authorized JL Audio dealer so
that it may be sent in to JL Audio for service.
There are no user serviceable parts or fuses inside
the amplifier. The unique nature of the circuitry
in the JL Audio amplifiers requires specifically
trained service personnel. Do not attempt
to service the amplifier yourself or through
unauthorized repair facilities. This will not only
void the warranty, but may result in the creation of
more problems within the amplifier.
If you have any questions about the installation or
setup of the amplifier not covered in this manual,
please contact your dealer or technical support.
Jl audio technical support:
(954) 443-1100
9:00 AM – 5:30 PM (Eastern Time Zone)
Monday - Friday
11
Hide quick links:
Advertisement
Table of Contents
