Sd Card Slot. - Panasonic DMP-BD65 Operating Instructions Manual

Picture
The images from this unit do not appear on
the television.
Picture is distorted.
An incorrect resolution is selected in "Component
Resolution" [BD65] or "HDMI Video Format". Reset the
setting as follows:
1 While the unit is on, press and hold [OK], the yellow
button and the blue button on the remote control at the
same time for more than 5 seconds.
– "00 RET" is displayed on the unit's display.
2 Repeatedly press [1](right) on the remote control or [Í/I]
on the unit until "04 PRG" is displayed on the unit's
display.
3 Press and hold [OK] on the remote control or [< OPEN/
CLOSE] on the unit for at least 3 seconds.
Set the item again. ( 28)
– When Dolby Digital Plus, Dolby TrueHD, and DTS-HD audio
are not output in bitstream, select "Yes" in "Default Settings"
and make proper settings. (
The unit and television are using different video systems.
While stopped, keep pressing [∫] and [< OPEN/CLOSE]
on the main unit for 5 or more seconds. The system
switches from PAL to NTSC or vice versa.
The system used on the disc doesn't match your
television.
– PAL discs cannot be correctly viewed on an NTSC
television.
– This unit can convert NTSC signals to PAL60 for viewing
on a PAL television ("NTSC Contents Output" in the
"Picture").
Video is not output in high definition.
Confirm that the "HDMI Video Mode" [BD65], "HDMI Video
Format", and "Component Resolution" [BD65] in the Setup
menu are set properly. (
[BD65] The video output resolution is restricted to "576p/
480p" when DVD-Video discs, DivX and BD-Video discs
recorded at a rate of 50 field per second are output from
the COMPONENT VIDEO OUT terminals.
A black band is displayed around the edge of
the screen.
The aspect ratio of the screen is abnormal.
Confirm the "TV Aspect" is set properly. (
Adjust the aspect setting on the television.
(Adjustment using "Screen Aspect" (
also possible.)
29)
28)
28)
17) on the unit is
Audio
Cannot switch audio.
When connecting an amplifier/receiver using an OPTICAL
terminal or an HDMI terminal, you cannot switch the audio
if "Digital Audio Output" is set to "Bitstream". Set "Digital
Audio Output" to "PCM" or connect using AUDIO OUT
terminal. ( 9, 27)
Cannot hear the desired audio type.
Check the connections and the "Digital Audio Output"
settings. ( 27)
To output audio from a device connected with an HDMI
cable, set "HDMI Audio Output" to "On" in the Setup
menu. ( 28)
Playback
Disc cannot be played.
The disc is dirty. ( 4)
Check the region code.
The contents of the USB device cannot be
read.
[BD65] USB devices connected using USB extension
cable other than the supplied with the Wireless LAN
Adaptor DY-WL10 (optional) or a USB hub may not be
recognized by this unit.
If inserted during playback the USB device may not be
recognized by this unit.
[BD65] If two USB devices other than Wireless LAN
adaptor are connected simultaneously, they will not be
recognized by this unit.
Still pictures (JPEG) do not playback
normally.
The images that were edited on the PC, such as
Progressive JPEG, etc., may not playback.
I can't play back BD-Live.
The SD card is write-protected. (
Confirm that this unit is connected to the broadband
Internet. ( 10, 29)
Confirm the "BD-Live Internet Access" settings. (
Confirm an SD Card is inserted into the SD Card slot.
( 15)
Network
[BD65]
I can't connect to the network.
Confirm the network connection and settings. (
Check the operating instructions for each device and
connect accordingly.
[BD65]
7)
26)
10, 29)
31
VQT2H94